JINGSHUNLI TP.SK713S.PC822(N)

Contents

TP.SK713S.PC822(N) 4K TV WiFi Network Motherboard User Manual

For Professional Technicians Only

1. Introduction

This manual provides essential information for the installation, operation, and maintenance of the TP.SK713S.PC822(N) 4K TV WiFi Network Motherboard. This product is a 'three-in-one' mainboard designed for 4K televisions, integrating various functionalities including WiFi network capabilities. It has been tested to ensure proper function.

Kind Reminder: The TV motherboard is a professional TV accessory. Please do not purchase or attempt installation unless you are an electronic technician. Non-professional technicians should seek assistance from qualified personnel to diagnose TV malfunctions before purchasing. Installation may require swapping data chips (e.g., EEPROM), writing data with programmers, or adjusting screen parameters in factory mode.

Top view of the TP.SK713S.PC822(N) 4K TV WiFi Network Motherboard
Figure 1: Top view of the TP.SK713S.PC822(N) Motherboard, showing various components and port layout.
Close-up of the model number TP.SK713S.PC822(N) on the motherboard
Figure 2: Close-up view confirming the model number TP.SK713S.PC822(N) printed on the circuit board.

2. Setup and Installation

Installation of the motherboard requires careful handling and adherence to safety procedures. Ensure the TV is disconnected from all power sources before beginning.

2.1 Pre-installation Checks

  • Verify the compatibility of the TP.SK713S.PC822(N) motherboard with your specific TV model.
  • Ensure you have the necessary tools, including screwdrivers, anti-static wrist strap, and a multimeter.
  • Familiarize yourself with the TV's internal layout and existing connections.

2.2 Physical Installation

  1. Disassembly: Carefully open the TV casing and remove the old motherboard. Document all cable connections and screw locations.
  2. Mounting: Position the new TP.SK713S.PC822(N) motherboard in the TV chassis, aligning it with the mounting holes. Secure it with the appropriate screws.
  3. Connecting Cables: Reconnect all necessary cables. Pay close attention to the following connections:
    • Power Input: Connect the main power supply cable to the designated power input area.
    • Display Panel (LVDS): Connect the LVDS cable from the display panel to the corresponding connector on the motherboard. This is often a wide, flat cable.
    • Backlight: Connect the backlight power cable.
    • Antenna/Tuner Inputs: Connect the antenna or cable TV input cables (refer to Figure 3 for typical locations).
    • Other Peripherals: Connect any other cables such as speakers, IR sensor, control panel buttons, and USB/HDMI ports.
Motherboard with arrows pointing to LVDS and antenna connectors
Figure 3: Key connection points on the motherboard, including the LVDS connector (right arrow) and antenna inputs (bottom arrows).
Motherboard with arrows indicating power input and other connectors
Figure 4: Additional connection points, possibly indicating power input (top right arrow) and other peripheral connectors.
Motherboard with arrows highlighting various power and signal connections
Figure 5: Overview of various power and signal connections on the motherboard.

2.3 Initial Power-On and Configuration

After physical installation, carefully reassemble the TV. Connect the TV to power and perform initial checks.

  • Software: The motherboard typically comes with pre-installed software. No additional software installation is usually required.
  • Screen Parameters: Depending on the TV panel, it may be necessary to adjust screen parameters or write specific programs via USB in factory mode. Consult the TV's service manual for detailed instructions on accessing factory mode and adjusting settings.

3. Operating Instructions

Once installed and configured, the motherboard functions as the central control unit for your TV. Operation is typically through the TV's remote control or integrated buttons.

  • Power On/Off: Use the TV remote or power button to turn the TV on or off.
  • Input Selection: Select desired input sources (HDMI, USB, AV, TV tuner) using the remote control.
  • Network Connectivity: Utilize the integrated WiFi for internet access and smart TV features. Refer to your TV's user interface for network setup.
  • Firmware Updates: Periodically check for firmware updates through the TV's settings menu to ensure optimal performance and access to new features. Updates are often performed via USB.

4. Maintenance

Proper maintenance ensures the longevity and reliable operation of the motherboard.

  • Cleaning: Keep the TV's ventilation openings clear of dust to prevent overheating. Use a soft, dry cloth for external cleaning. For internal cleaning (only by professionals), use compressed air to remove dust from the motherboard components.
  • Environmental Conditions: Operate the TV in a well-ventilated area, away from direct sunlight, excessive heat, and moisture.
  • Power Fluctuations: Consider using a surge protector to safeguard the motherboard from power spikes.

5. Troubleshooting

This section provides solutions to common issues. For complex problems, consult a professional technician.

Problem Possible Cause Solution
TV does not power on. Loose power connection, faulty power supply, incorrect motherboard installation. Check all power connections. Verify power supply unit. Re-check motherboard installation.
No picture, but sound is present. LVDS cable issue, backlight problem, incorrect screen parameters. Ensure LVDS cable is securely connected. Check backlight connections. Adjust screen parameters in factory mode if necessary.
No sound, but picture is present. Speaker connection issue, audio settings. Check speaker connections. Verify TV audio settings.
WiFi not connecting. Incorrect network settings, WiFi module issue. Check network settings in TV menu. Restart router. If issue persists, WiFi module may be faulty.

6. Specifications

Feature Detail
Model Number TP.SK713S.PC822(N)
Compatible Equipment Style Display Equipment (TVs)
Origin Mainland China
High-concerned chemical None
Input Voltage 100V-180V
Input Current 500mA
Power Output 108W (as indicated by '108W2' on label)
Efficiency/Duty Cycle 50% (as indicated on label)
QR code with power specifications for the motherboard
Figure 6: QR code label displaying electrical specifications.
Bottom view of the motherboard with protective cover
Figure 7: Bottom view of the motherboard, showing the protective cover.

7. User Tips

  • Pre-installed Software: The motherboard typically comes with its operating software already installed. There is usually no need to install software again after replacement.
  • Data Transfer: In some cases, especially if replacing a faulty board, it might be necessary to transfer data chips (like EEPROM) from the old board to the new one, or to write specific data using a programmer. This ensures compatibility with the TV's panel and existing settings.
  • Factory Mode Adjustments: Be prepared to enter the TV's factory service mode to adjust screen parameters (e.g., panel type, resolution) after installation, as this is a common requirement for new mainboards.

8. Support

For technical assistance or inquiries regarding this product, please contact the seller, JINGSHUNLI LED LCD TV accessories Store. They offer pre-sales consultation and after-sales technical support.

All boards are tested before shipping to ensure quality.

© 2023 JINGSHUNLI LED LCD TV accessories Store. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.