1. Product Overview
The SUNSUN JQP Series Internal Aquarium Filter is a versatile 3-in-1 device designed for aquariums, functioning as a filter, submersible pump, and oxygenator. It is engineered for silent operation and efficient water purification, circulation, and oxygenation, contributing to a healthy aquatic environment.
Key Features:
- Easy to install and operate.
- Waterproof design with excellent insulation performance.
- Multifunctional: Provides water circulation, filtration, wave-making, and oxygenation.
- Equipped with built-in double-layer filter cotton for effective impurity removal.
- Filter material in the filter box can be replaced according to specific needs.
- JQP-500F, JQP-1000F, and JQP-1500F models feature a stainless steel rotor for durability.





2. Safety Information
Warning! Please read all safety instructions carefully before use.
- Electrical Safety: This product is an electrical device involving high voltage. Always adhere to electrical safety regulations to prevent electric shock. Minors and elderly individuals must use the product under adult supervision.
- Children's Safety: This product is not suitable for children under 36 months due to small parts (screws, filter media, connection fittings, air stone) which pose a choking hazard. Keep children away from power interfaces and moving parts.
- Power & Heat: Keep the product away from heat sources (e.g., heaters, lamps, open flames) during operation. Do not leave unattended for extended periods to prevent overheating or fire. Immediately replace any damaged or aged power cords with original replacements.
- Waterproof Integrity: While the filter and pump are waterproof, do not use them beyond the marked waterproof depth. Do not use if the casing is damaged or seals are compromised, as this may lead to leaks and electric shock. The pump must always be fully submerged to prevent dry running and potential damage.
- Disposal: Electronic components and batteries (if any) must be disposed of according to EU WEEE Directive (2012/19/EU) and Hazardous Waste Directive (2008/98/EC). Hand over to professional recycling agencies; do not discard randomly to prevent environmental pollution.
- Skin/Eye Contact: If the product comes into contact with skin and causes discomfort, rinse immediately with clean water.
- Moving Parts: Do not touch the impeller or any rotating parts of the submersible pump or oxygen pump while they are operating to prevent mechanical injury.
3. Setup Instructions
Before proceeding with installation, ensure you have read this manual thoroughly. Verify that the product's rated voltage matches your power supply. Always disconnect power before installation, cleaning, or maintenance.
3.1 General Setup Guidelines
- Read the instruction manual carefully before use.
- Ensure the product's rated voltage matches your power supply. Do not use with non-rated voltage.
- Always disconnect power before installation, disassembly, cleaning, or maintenance. Wait for the product to stop completely and cool down to avoid electric shock or mechanical injury.
- Rinse all parts that will contact water with clean water before installation. Do not use chemical solvents (e.g., alcohol, disinfectants) to clean, as this may contaminate the water or harm aquatic life.
- Install the product in a location inaccessible to children.
3.2 Specific Setup Steps for Internal Aquarium Filter
- Mounting: Securely attach the filter to the side or top of the aquarium using the non-slip suction cups. Ensure it is firmly fixed to prevent detachment.
- Submersion: Place the submersible pump vertically in the tank, ensuring it is fully submerged in water to prevent dry running. Secure its position to prevent shaking during operation.
- Connections: Connect the outlet pipe and adjust the water flow direction as desired.
- Filter Media: Place the filter cotton, biochemical cotton, and other filter media into the filter chamber according to the instructions, ensuring they are arranged neatly.
- Oxygenation Port: If using the oxygenation function, ensure the detachable oxygenation port is properly connected and adjusted.


4. Operating Instructions
4.1 Internal Aquarium Filter Operation
- Power On: After confirming correct installation and full submersion, connect the power. Verify that the filter operates normally, water flow is stable, and there are no abnormal noises or jamming. If dry running occurs, immediately disconnect power and readjust the pump's position.
4.2 Oxygenation Function
- Detachable Oxygenation Port: The filter includes a detachable oxygenation port. Adjust the port to control the amount of oxygen introduced into the tank.
- Intake Valve: Ensure the intake valve is properly positioned and clear for efficient oxygen intake.
- Air Volume Adjustment: Adjust the air volume based on the oxygen demand of your aquatic environment, especially for high-density fish, during high temperatures, or at night.


5. Maintenance & Care
Regular maintenance ensures optimal performance and longevity of your aquarium filter.
5.1 Daily Cleaning & Routine Checks
- Filter Media: Clean filter media (filter cotton, biochemical cotton) every 1-2 weeks using clean water. Do not use detergents. Inspect inlet/outlet pipes monthly and clean any blockages.
- Submersible Pump: Clean the inlet filter every 2 weeks with a soft brush to remove debris. Check the pump's seal monthly; if leakage or looseness occurs, contact customer service for repair.
- Oxygenation Components: Clean the air stone and air tube monthly with clean water to remove impurities. Check air tube connections for leaks. Clean the air inlet filter to prevent blockages and maintain air output.
5.2 Storage Requirements
- Long-term Storage: If the product will not be used for an extended period, disconnect the power. Remove and thoroughly clean all components (submersible pump, filter) and ensure they are completely dry. Store in a dry, cool, ventilated place, away from direct sunlight, moisture, and heavy objects.
- General: Avoid contact with sharp objects during storage to prevent casing damage. Store accessories (filter media, screws) separately to prevent loss.
5.3 Maintenance Precautions
- Filter Media Replacement: Replace filter media every 3-6 months. When replacing, do so gradually (e.g., one layer at a time) to maintain the stability of the nitrification system.
- Pump Operation: Avoid continuous operation of the submersible pump for excessively long periods. It is recommended to allow it to rest for 1-2 hours after every 24 hours of operation to extend its lifespan.
6. Troubleshooting
Refer to the table below for common issues and their solutions. Always disconnect power before attempting any troubleshooting or repairs.
| Problem | Possible Cause | Solution |
|---|---|---|
| Filter/Pump not running | 1. Power not connected 2. Power adapter damaged 3. Motor fault 4. Debris blocking moving parts | 1. Check power connection 2. Replace with original power adapter 3. Contact customer service for motor repair 4. Disconnect power and clean debris |
| Filter/Pump leaking | 1. Poor interface seal 2. Casing damaged 3. Hose aging/loose | 1. Reinstall and reseal interface 2. Contact customer service to replace casing 3. Replace original hose |
| Oxygen pump low/no air output | 1. Air stone/tube blocked 2. Air inlet filter blocked 3. Motor fault 4. Interface leak | 1. Clean air stone/tube 2. Clean air inlet filter 3. Contact customer service for motor repair 4. Check and reseal interface |
| Device operating with abnormal noise | 1. Loose installation 2. Debris in moving parts 3. Motor aging 4. Air inlet abnormal | 1. Re-secure device 2. Disconnect power and clean debris 3. Contact customer service for motor repair 4. Clean air inlet |
| Filter ineffective | 1. Filter media blocked/aged 2. Incorrect water flow setting 3. Filter media misplaced | 1. Clean/replace filter media 2. Adjust water flow according to manual 3. Reposition filter media |
7. Specifications
The SUNSUN JQP Series offers various models with different power, lift, and flow rates to suit various aquarium sizes.

| Parameter | JQP-500F | JQP-1000F | JQP-1500F | JQP-2500F |
|---|---|---|---|---|
| Power | 5W | 14W | 20W | 35W |
| Max Lift | 0.9m | 1.4m | 1.7m | 2.4m |
| Max Flow | 500L/h | 1000L/h | 1500L/h | 2500L/h |
| Size (mm) | 65x51x215 | 76x60x288 | 87x68x370 | 96x75x380 |
| Filter Box | 2 | 3 | 3 | 3 |
| Power Cord | 1.5m | 1.5m | 1.5m | 1.8m |
Additional Specifications:
- Waterproof Rating: IPX7 (for submersible pump).
- Recommended Tank Size for JQP-500F: Up to 60cm.

8. User Tips
- Regular Cleaning is Key: To maintain optimal water quality and filter performance, ensure you clean the filter media and pump rotor regularly as recommended in the maintenance section. This will keep your tank clean and healthy.
- Tank Size Matching: When selecting a model, ensure it is appropriate for your aquarium size. For example, the JQP-500F model is suitable for fish tanks up to 60cm in length.
- Prevent Dry Running: Always ensure the submersible pump is fully submerged in water before powering it on to prevent damage from dry running.

9. Warranty & Support
For any inquiries, technical support, or warranty claims, please contact our customer service team:
- Customer Service Email: magicaqua17@163.com
- Customer Service Phone: 0086-13512793658
- After-sales Service Hours: Monday to Sunday, 9:00 - 18:00 (Beijing Time)
Please have your product model and purchase information ready when contacting support.
10. Compliance Statement
This product complies with relevant EU regulations and harmonized standards, including:
10.1 General Compliance Directives (Applicable to all categories)
- Low Voltage Directive (LVD) 2014/35/EU: Ensures electrical safety for equipment operating within specified voltage ranges.
- Electromagnetic Compatibility (EMC) 2014/30/EU: Guarantees the product does not generate excessive electromagnetic interference and is immune to external interference.
- Restriction of Hazardous Substances (RoHS) 2011/65/EU: Limits hazardous substances like lead, mercury, and cadmium to protect human health and the environment.
- Waste Electrical and Electronic Equipment (WEEE) 2012/19/EU: Regulates the recycling and disposal of electronic waste to reduce environmental pollution.
10.2 Category-Specific Harmonized Standards
- Fish Tank Filter & Submersible Pump: Complies with EN 60335-1 (General requirements for household appliances) and EN 60335-2-55 (Specific requirements for aquarium and pond appliances), covering waterproofing, electrical safety, and mechanical safety. Requires IPX7 waterproof rating and a minimum 2mm distance between live parts and water. Also meets EN 60335-2-41 (Specific requirements for pumps) and EN ISO 12100 (Safety of machinery - General principles for design).
- Aquarium Oxygen Pump: Complies with EN 60335-1 and EN 60335-2-41, with specific regulations for motor safety, noise control, and airtightness. Also meets EN ISO 12100 (Safety of machinery - General principles for design).
This product has successfully undergone compliance testing, risk assessment, and has a complete technical file (TCF). A Declaration of Conformity (DoC) has been signed, allowing legal sale and use within the EU. Technical files and DoC will be retained for at least 10 years and can be provided to EU regulatory authorities upon request.