1. Introduction
The Flipsky 75200 Pro V2.0 is a high-performance VESC-based Electronic Speed Controller (ESC) designed for electric skateboards, scooters, and e-bikes. It features an aluminum PCB for enhanced heat dissipation and durability, supporting a wide voltage range and various control modes. This manual provides essential information for the proper installation, operation, and maintenance of your speed controller.

Figure 1: Flipsky 75200 Pro V2.0 Speed Controller (Power Button variant)
2. Specifications
Below are the detailed technical specifications for the Flipsky 75200 Pro V2.0 Speed Controller:
| Parameter | Value |
|---|---|
| Firmware | 6.02 (supports upgrade) |
| Voltage Range | 14-84V (safe for 4-20S battery configurations) |
| Continuous Current | 50V/200A; 75V/150A (dependent on mounting, ambient temperature, and air/water circulation) |
| Burst Current | 300A |
| BEC Output | 5V@1A |
| Supported Modes | DC, BLDC, FOC (sinusoidal) |
| ERPM | 150,000 |
| Communication Ports | USB, CAN, UART, SPI, IIC |
| Supported Sensors | ABI, HALL, AS5047, AS5048A |
| Input Source Support | PPM, ADC, NRF, UART |
| Sensorless Operation | Yes |
| Regenerative Capacity | Yes |
| Programmability | Via VESC_TOOL |
| Dimensions (LxWxH) | 130x68x41mm |
| Motor/Power Wire Size | 8 AWG |
| Phase Filter | Yes |
| Material | Metal (Aluminum PCB) |
| Recommended Age | 14+ years |
| Certification | CE, RoHS |

Figure 2: Physical dimensions of the 75200 Pro V2.0 controller.
3. Key Features
- Comprehensive Protection: Features adjustable safeguards against low voltage, high voltage, over current, abnormal temperature, and MOSFET/motor over-temperature conditions.
- Versatile Control Modes: Supports Current, Duty Cycle, Speed, and PID control modes for flexible application.
- IMU Module Support: Enables balancing car functionality by connecting IMU modules (e.g., MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160) via the IIC interface.
- High-Performance CPU: Equipped with a 32F405 CPU operating at 168MHz for efficient processing.
- Enhanced Heat Dissipation: Utilizes an aluminum PCB design for superior heat management, extending the lifespan of the device.
- Integrated Connectivity: The 75200 Pro V2.0 single drive model includes a single serial port function and an integrated Bluetooth module for convenient parameter adjustment and real-time data monitoring.
- Built-in Power Switch: Features a built-in power on/off switch for ease of use.
4. Installation and Wiring Setup
Careful wiring is crucial for the proper and safe operation of your Flipsky 75200 Pro V2.0 speed controller. Refer to the detailed wiring diagram below and follow these steps:

Figure 3: Detailed wiring connections for the 75200 Pro V2.0 controller.
Wiring Instructions:
- Battery Connection: Connect your battery's positive (red) and negative (black) terminals to the corresponding large red and black wires on the ESC. Ensure correct polarity.
- Motor Connection: Connect the three phase wires (blue, green, yellow) from your motor to the corresponding output wires on the ESC.
- Power Switch (1): Connect the power switch to the designated "POWER SWITCH" port. Note the warning: "Please press here to unplug the connectors. Do not pull directly to avoid wires & connectors broken."
- Hall Sensors (2): If your motor uses Hall sensors, connect them to the "HALL" port. This typically involves 5V, GND, and three signal wires (HALL1, HALL2, HALL3).
- PPM (3): Connect your PPM receiver (e.g., for remote control) to the "PPM" port. This usually includes SERVO, 5V, and GND.
- CAN+POWER (4): Use the CAN port for communication between multiple ESCs (master/slave configuration) or other CAN-enabled devices. The diagram shows GND, CANL, CANH, 5V, and PWR.ON.
- USB (5): Connect a USB cable to this port for configuration and firmware updates using VESC_TOOL on a computer.
- COMM (6): This port provides additional communication options, including ADC15, ADC2, TX/SCL, RX/SDA, ADC1, GND, 3.3V, and 5V. It can be used for various peripherals or debugging.
Important: Always double-check all connections before applying power to prevent damage to the ESC or other components. Incorrect wiring can lead to permanent damage and void the warranty.
5. Operation
Powering On/Off:
The 75200 Pro V2.0 features a built-in power on/off switch. Use this switch to safely power the controller on and off. Ensure all connections are secure before powering on.
Configuration and Monitoring:
- VESC_TOOL: The controller is fully programmable via VESC_TOOL software. Connect the ESC to your computer using a USB cable to access and adjust parameters, perform motor detection, and update firmware.
- Bluetooth Module: The integrated Bluetooth module allows for convenient wireless connection to compatible applications (e.g., VESC Tool mobile app) for parameter adjustment and real-time data monitoring.
Control Modes:
The ESC supports various control modes, including Current, Duty Cycle, Speed, and PID control. These can be configured through VESC_TOOL to match your specific application requirements.
6. Maintenance
- Heat Management: The aluminum PCB is designed for good heat dissipation. Ensure the controller is mounted in a location with adequate air circulation. For high-power applications, consider additional cooling if necessary to maintain optimal operating temperatures.
- Connection Integrity: Regularly inspect all wire connections for signs of wear, corrosion, or looseness. Secure any loose connections. When disconnecting, always press the release tabs on connectors and avoid pulling directly on wires.
- Cleanliness: Keep the controller free from dust, dirt, and moisture. Use a soft, dry cloth to clean the exterior. Avoid using liquids or solvents.
- Firmware Updates: Periodically check for firmware updates via VESC_TOOL to ensure optimal performance and access to new features.
7. Troubleshooting
The Flipsky 75200 Pro V2.0 includes several protection features to prevent damage. If you encounter issues, consider the following:
- No Power/No Response:
- Check battery connections and ensure the battery is charged.
- Verify the power switch is correctly connected and functioning.
- Inspect all wiring for loose connections or damage.
- Motor Not Spinning/Irregular Operation:
- Perform motor detection using VESC_TOOL.
- Check Hall sensor connections if using sensored mode.
- Verify PPM/UART input signals from your remote or control device.
- Ensure motor phase wires are correctly connected.
- Over-Temperature Protection Triggered:
- Reduce load or operating intensity.
- Improve air circulation around the ESC.
- Check for proper mounting and ensure no obstructions to cooling.
- Over-Current Protection Triggered:
- Check for motor short circuits or excessive load.
- Review current limits in VESC_TOOL settings.
- Voltage Protection Triggered (Low/High):
- Ensure your battery voltage is within the 14-84V (4-20S) safe operating range.
- Check battery health and charging status.
- Verify voltage cutoff settings in VESC_TOOL.
- Communication Issues (USB/Bluetooth):
- Ensure correct drivers are installed for USB.
- Verify Bluetooth is enabled on your device and the ESC.
- Try restarting both the ESC and your communication device.
If issues persist after following these steps, consult the VESC_TOOL documentation or contact Flipsky support.
8. User Tips
- VESC_TOOL Configuration: Always use the latest version of VESC_TOOL for configuration and firmware updates. Familiarize yourself with the software's motor setup wizard for optimal performance.
- Heat Management: For demanding applications, consider adding a small fan or ensuring ample airflow around the ESC to prevent thermal throttling and extend component life.
- Secure Connections: Vibration can loosen connections over time. Use thread locker on screws and secure wire bundles to prevent accidental disconnections.
9. Warranty and Support
Warranty Policy:
The warranty period for consumable electronic products, such as this ESC, is 2 months, starting from the 7th day after shipment (as per logistics record). For non-electronic products, the warranty period is also 2 months from the 7th day after shipment.
If a product requires repair, the customer is responsible for the shipping cost to the service center. If repair is not feasible, a replacement may be offered, with the customer covering the shipping cost for the replacement unit.
Warranty Exclusions:
The warranty does not cover:
- Mechanical damage to electronic components or the PCB.
- Repair soldering iron traces on the PCB board (excluding cable bullet connectors).
- Wire damage or external impact damage.
- Water inflow for non-waterproof products.
- Damage resulting from abnormal applications or use beyond product specifications.
- Products purchased from channels other than Flipsky's official channels.
- Products without original purchase channel proof or second transaction proof.
Clarification: All products are tested before shipment. The seller is not liable for damage caused by incorrect installation or improper VESC/motor settings. Please ensure correct installation and configuration. Shipping costs for warranty claims are the responsibility of the customer.