Flipsky FSESC75100 Pro V2.0

Contents

Flipsky FSESC75100 Pro V2.0 Aluminum PCB Speed Controller User Manual

Model: FSESC75100 Pro V2.0

Brand: Flipsky

1. Introduction

The Flipsky FSESC75100 Pro V2.0 is an advanced Electronic Speed Controller (ESC) designed for high-performance electric vehicles such as e-skateboards, e-scooters, and ebikes. Based on VESC technology, it offers precise motor control with support for both BLDC square wave and FOC sine wave modes. This manual provides essential information for safe installation, operation, and maintenance of your controller.

2. Safety Information

WARNING: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. Improper use can lead to serious injury or damage. Always disconnect power before making any connections or disconnections. Ensure all wiring is secure and insulated.

  • Always wear appropriate safety gear when operating electric vehicles.
  • Ensure the battery is fully disconnected before performing any wiring or maintenance.
  • Avoid exposing the controller to water, moisture, or extreme temperatures.
  • Do not attempt to open or modify the controller, as this may void the warranty and cause damage.
  • Keep out of reach of children.

3. Package Contents

Your package should include the FSESC75100 Pro V2.0 controller and any selected accessories such as a power button or key switch. Please inspect all components for damage upon receipt.

Flipsky FSESC75100 Pro V2.0 with power button and display
Image: FSESC75100 Pro V2.0 controller with power button and display accessory.

4. Specifications

FeatureSpecification
Firmware6.02 (firmware update supported)
Dimensions (L*W*H)103mm * 58mm * 27.7mm
Voltage14-84V (4-20S)
Current100A Continuous
BEC5V@1.5A
Control ModesBLDC square wave, FOC sine wave
ERPM150000
Control Interface PortsUSB, CAN, UART
Supported SensorsABI, HALL, AS5047, AS5048A
Input Set SupportPPM, ADC, NRF, UART
Wire Size10AWG (75100 Pro)
ProgrammableYes
Regenerative CapacityYes
Phase FilterYes
Dimensions of the FSESC75100 Pro V2.0 controller
Image: Physical dimensions of the FSESC75100 Pro V2.0 controller.

5. Setup and Installation

Proper wiring is crucial for the safe and correct operation of your FSESC75100 Pro V2.0. Always ensure your battery is disconnected before making any connections. Refer to the detailed wiring diagram below and follow the instructions carefully. Incorrect wiring can damage the controller and other components.

Detailed wiring diagram for Flipsky FSESC75100 Pro V2.0
Image: Detailed wiring diagram for the FSESC75100 Pro V2.0, showing connections for battery, motor, power switch, Hall sensors, PPM, USB, CAN, and COMM ports. Note: To unplug connectors, press the release tab; do not pull directly on wires.

Connection Points:

  • Battery: Connect your main battery pack to the large red (+) and black (-) wires. Ensure correct polarity.
  • Motor: Connect the three motor phase wires to the corresponding outputs on the ESC.
  • Power Switch: Connect the power switch to the designated port (labeled 'POWER SWITCH' in the diagram).
  • Hall Sensors: If your motor uses Hall sensors, connect them to the 'HALL' port.
  • PPM: For remote control input, connect your PPM receiver to the 'PPM' port.
  • USB: Use the USB port for connecting to a computer for configuration via VESC tool.
  • CAN: For multi-ESC setups (master/slave), use the CAN bus port.
  • COMM: This port provides UART communication for accessories like Bluetooth modules or external displays.

Important: When disconnecting any JST-style connector, always press the small tab on the connector housing before gently pulling. Pulling directly on the wires can damage the connector or the PCB.

6. Operation

Once all connections are securely made and verified, you can proceed with operation:

  1. Power On: Connect your battery and press the power switch (if equipped). The LED indicator on the controller will illuminate, indicating power.
  2. Initial Configuration: Before first use, it is essential to configure the ESC using the VESC tool software. This includes motor detection, input device calibration (e.g., PPM remote), and setting battery parameters.
  3. Motor Control: After successful configuration, the motor can be controlled via your chosen input device (e.g., remote control).
  4. Power Off: Always turn off the controller using the power switch before disconnecting the battery.

7. Configuration

The FSESC75100 Pro V2.0 is highly programmable and utilizes VESC firmware 6.02. Configuration is performed using the official VESC tool software, which can be downloaded from the VESC project website. This tool allows you to:

  • Perform motor detection for optimal performance.
  • Calibrate your input device (PPM, ADC, etc.).
  • Set battery voltage limits and current limits.
  • Adjust motor control parameters (FOC, BLDC, current control, duty cycle control).
  • Update firmware.
  • Monitor real-time data and diagnose issues.

Connect the controller to your computer via the USB port for configuration. Detailed instructions for using the VESC tool are available in the VESC project documentation.

8. Maintenance

To ensure the longevity and optimal performance of your FSESC75100 Pro V2.0, follow these maintenance guidelines:

  • Cleaning: Keep the controller clean and free from dust, dirt, and debris. Use a soft, dry brush or compressed air.
  • Moisture: Avoid exposing the unit to water or excessive moisture. If it gets wet, disconnect power immediately and allow it to dry completely before re-applying power.
  • Connections: Periodically check all wire connections for tightness and signs of wear or corrosion. Re-secure or replace as necessary.
  • Cooling: Ensure adequate airflow around the controller, especially during demanding operation, to prevent overheating.
  • Storage: Store the controller in a dry, cool place when not in use.

9. Troubleshooting

If you encounter issues with your FSESC75100 Pro V2.0, consider the following troubleshooting steps:

  • No Power:
    - Check the main battery connection and ensure it is fully charged.
    - Verify the power switch is correctly connected and functioning.
    - Inspect for any blown fuses in your system.
  • Motor Not Spinning/Erratic Behavior:
    - Re-check all motor phase wire connections.
    - Verify Hall sensor connections (if used).
    - Re-run motor detection in the VESC tool.
    - Calibrate your input device (PPM remote, etc.) in the VESC tool.
  • Overheating:
    - Ensure the controller has sufficient airflow for cooling.
    - Check motor and battery current limits in the VESC tool; they might be set too high for your setup.
    - Verify that the motor is not overloaded or experiencing excessive resistance.
  • Communication Issues (USB/CAN/UART):
    - Ensure drivers are correctly installed for USB.
    - Check cable connections for damage or looseness.
    - Verify baud rates and other communication settings in the VESC tool.

For persistent issues, consult the VESC community forums or contact Flipsky support.

10. User Tips

  • Bluetooth Connectivity: The FSESC75100 Pro V2.0 includes built-in Bluetooth, allowing for wireless configuration and monitoring via compatible VESC mobile applications. This feature provides convenient access to settings and real-time data without needing a physical USB connection.
  • Firmware Updates: Regularly check for and install the latest VESC firmware updates to benefit from performance improvements, bug fixes, and new features. Always back up your configuration before updating.
  • Heat Management: For high-power applications, consider additional cooling solutions or ensure the controller is mounted in a location with excellent airflow to prevent thermal throttling.

11. Warranty and Support

Warranty Policy:

The warranty period for consumable electronic products (e.g., VESC/Motor/Battery) is 2 months, starting from the 7th day after shipment (shipping date verified by logistic record). For non-electronic products, the warranty period is also 2 months from the 7th day after shipment.

Return and Repair Process:

If you experience a manufacturing failure within the warranty period, please contact Flipsky customer support. We will guide you through the return process. If the product is found to be a manufacturing defect, a discount may be provided for a new replacement (shipping cost excluded). Wear and tear caused by normal use is not considered a defect.

Conditions Not Covered by Warranty:

  • Mechanical damage to electronic components or PCB.
  • PCB board repair or solder iron traces (excluding cable bullet connectors).
  • Water damage or external impact damage.
  • Any damage beyond product specifications.
  • Products purchased from other channels or through second-hand transactions.

Always retain your original purchase channel information and warranty card for any claims. The warranty is valid only for the original product and is not transferable to second-hand owners.

Customer Support:

For technical assistance, troubleshooting, or warranty claims, please contact Flipsky customer support through their official website or the contact information provided with your purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.