Racing R type bolt

Contents

RC Car Body Shell R Clips Instruction Manual

Essential guide for the proper use and care of your RC car body shell R clips.

Introduction

Thank you for choosing Racing RC Car Body Shell R Clips. These high-quality 304 stainless steel clips are designed to securely fasten the body shell of your remote control car, ensuring stability and protection during operation. This manual provides detailed instructions for selecting, installing, maintaining, and troubleshooting your R clips to enhance your RC experience.

Product Overview

The R clips are available in various sizes to accommodate different RC car scales, including 1/5, 1/6, 1/7, 1/8, 1/10, 1/12, 1/14, 1/16, and 1/18. Each set typically contains 20 or 50 pieces, providing ample supply for your needs. They are constructed from durable 304 stainless steel for longevity and resistance to bending.

Assortment of R clips for 1/8, 1/10, 1/16 scale RC cars
Figure 1: Assortment of R clips for 1/8, 1/10, and 1/16 scale RC cars.
Video 1: Demonstration of RC car body shell R clips in use.

Specifications

AttributeDetail
Material304 Stainless Steel
Model NumberR type bolt
For Vehicle TypeCars (RC Buggy, Truck, etc.)
UseVehicles & Remote Control Toys
Recommended Age14+ years
Quantity per set20 or 50 pieces (optional)

Dimensions

Detailed dimensions for 1/8, 1/10, and 1/16 scale R clips
Figure 2: Detailed dimensions for various R clip sizes.
ScaleLengthLoop WidthWire Diameter
1/833 mm12.3 mm1.4 mm
1/1024 mm8.5 mm1.2 mm
1/1619 mm6.5 mm1 mm

Setup

The primary setup involves selecting the correct size of R clip for your specific RC car model. Refer to the 'Specifications' section for detailed dimensions. Once the appropriate size is chosen, the clips are ready for immediate use.

Operating Instructions

To secure your RC car body shell:

  1. Align the body shell with the mounting posts on your RC car chassis.
  2. Push the body shell down until the mounting posts protrude through the designated holes in the body.
  3. Take an R clip and insert one of its prongs into the hole of a mounting post.
  4. Push the clip through the post until both prongs are fully engaged, securing the body shell in place.
  5. Repeat for all necessary mounting posts (typically four).

To remove the body shell, simply reverse the process by pulling the R clips out from the mounting posts.

Close-up of an R clip securing an RC car body
Figure 3: Proper installation of an R clip on an RC car body post.

Maintenance

These R clips are made from durable 304 stainless steel and require minimal maintenance. To ensure their longevity and proper function:

  • Cleaning: Periodically wipe the clips clean with a dry cloth to remove dirt, dust, or debris. If exposed to mud or corrosive substances, clean with mild soap and water, then dry thoroughly to prevent water spots.
  • Inspection: Regularly inspect clips for any signs of bending, deformation, or damage. While 304 stainless steel is robust, extreme forces can cause wear.
  • Storage: Store unused clips in a dry, secure container to prevent loss and keep them free from contaminants. The clips are typically supplied in resealable bags for convenient storage.
Packaged R clips
Figure 4: R clips as typically packaged for storage.

Troubleshooting

  • Clip is too loose/falls out: Ensure you are using the correct size clip for your RC car's body posts. If the clip is the correct size but still loose, the body post might be worn, or the clip itself may be slightly bent. Try a new clip or consider replacing worn body posts.
  • Clip is too tight/difficult to insert: Verify that the clip size matches your RC car's scale. For new clips, a tight fit is normal and indicates a secure hold. Avoid forcing clips that are clearly too small, as this can damage the body posts or the clips.
  • Clip is bent or broken: Replace immediately with a new clip. Bent clips may not provide a secure hold and could lead to the body shell detaching during use.
  • Lost clips: Keep spare clips readily available. It is common to lose small parts like R clips during RC car activities.

User Tips

  • For easier handling and visibility, especially during outdoor use, consider using slightly larger R clips than the standard ones that might have come with your RC car.
  • These clips are noted for their strength and tight fit, making them ideal for securing RC bodies, even those with minor cracks.
  • Many users find these clips to be sturdier and more reliable than those supplied with some well-known RC brands.
  • Always have a few spare clips on hand, as they are small and can be easily misplaced during intense RC sessions.

Warranty and Support

This product is manufactured to high-quality standards. For any questions, concerns, or support regarding your Racing RC Car Body Shell R Clips, please contact the seller directly through the platform where the purchase was made. Please retain your purchase receipt for any potential warranty claims, though specific warranty details for this accessory are not provided.

© 2024 Racing RC Store. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.