MagTool MagTool DC Gyre Wave Maker

Contents

MagTool Aquarium DC Gyre Wave Maker

Models: MT-1600, MT-2400, MT-4200

1. Introduction

Thank you for choosing the MagTool DC Gyre Wave Maker. This innovative cross-flow pump is designed to simulate natural ocean currents in your aquarium, providing optimal water circulation and a healthy environment for your aquatic life. Featuring advanced sine wave technology for silent operation, versatile flow modes, and an intuitive LCD controller, the MagTool Wave Maker offers precise control and energy efficiency. Please read this manual thoroughly before installation and operation to ensure safe and effective use.

MagTool DC Gyre Wave Maker with its controller
Figure 1: MagTool DC Gyre Wave Maker and Controller

2. Package Contents

Please check the box for the following items:

  • MagTool DC Gyre Wave Maker Unit
  • LCD Controller
  • Power Adapter
  • User Manual (this document)
Contents of the MagTool DC Gyre Wave Maker package
Figure 2: What's in the Box

3. Specifications

FeatureDescription
VoltageDC 24V (AC 110-240V Input)
Wave ModesConstant, Pulse, Tidal, Turbulent (Random)
Adjustable Frequencies11 levels (Pulse and Tidal modes)
Feeding Mode10-minute pause
InstallationMagnetic suction (up to 15mm glass thickness)
Noise LevelUltra-quiet (Sine wave technology, shock-absorbing rubber)

Model Specifics

ModelMin. PowerMax. PowerMax. Flow (GPH/LPH)Recommended Tank SizeDimensions (A/B/C/D)
MT-16007.2W18W1600GPH (6000LPH)45-80cm (18-31inch)16cm/26cm/7cm/3.4cm
MT-240011.2W28W2400GPH (9100LPH)90-120cm (35-47inch)18cm/30cm/7.2cm/3.8cm
MT-420018W45W4200GPH (16000LPH)120-150cm (47-60inch)18cm/30cm/7.2cm/3.8cm
Diagram showing dimensions A, B, C, D for the wave maker and a table of specifications for MT-1600, MT-2400, and MT-4200 models.
Figure 3: Product Dimensions and Model Specifications

4. Safety Instructions

  • Always unplug the device from the power outlet before performing any maintenance, cleaning, or handling the pump.
  • Do not operate the pump if the power cord or plug is damaged.
  • Ensure your hands are dry when plugging or unplugging the power adapter.
  • This device is designed for indoor aquarium use only. Do not use it for other purposes.
  • Keep the controller and power adapter away from water.
  • Ensure a drip loop is formed with the power cord to prevent water from traveling along the cord and reaching the electrical outlet.
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

5. Setup and Installation

Follow these steps to install your MagTool DC Gyre Wave Maker:

  1. Unpack: Carefully remove all components from the packaging.
  2. Mount the Wave Maker: The wave maker uses a magnetic suction mounting system. Identify the two parts of the magnetic mount. Place the wave maker unit inside the aquarium at your desired location. Align the external magnet on the outside of the aquarium glass, directly opposite the internal magnet attached to the wave maker. The powerful magnets will secure the unit in place. Ensure the glass thickness does not exceed 15mm for secure attachment.
  3. Positioning: Position the wave maker to achieve optimal water flow throughout your tank. The 360-degree adjustable dual outlets allow you to direct flow precisely.
  4. Connect Controller: Connect the wave maker unit to the LCD controller, and then connect the power adapter to the controller.
  5. Secure Cables: Arrange the power cables to prevent accidental dislodgement and create a drip loop to prevent water from reaching electrical outlets.
  6. Power On: Plug the power adapter into a suitable electrical outlet. The LCD controller will light up.
Close-up view of the magnetic suction installation method for the wave maker
Figure 4: Magnetic Suction Installation
MagTool Wave Maker installed in an aquarium, showing its placement near the water surface
Figure 5: Wave Maker Installed in Aquarium

6. Operating Instructions

Controller Overview

Diagram of the LCD controller showing LED display, intensity buttons, feeding button, mode button, and frequency adjustment knob
Figure 6: LCD Controller Interface
  • LED Display: Shows current power (Watt), flow intensity (%), and gear/frequency.
  • Intensity Buttons (+/-): Adjust the flow intensity.
  • Feeding Button (F) / Power ON/OFF: Short press to activate feeding mode; long press to power the unit ON/OFF.
  • Mode Button (M): Cycle through the different wave modes.
  • Frequency Adjustment Knob: Adjusts wave frequency in Pulse and Tidal modes.

Wave Modes

The MagTool Wave Maker offers four distinct wave modes:

  1. Constant Flow Mode: Provides a stable and continuous water flow, ideal for a tranquil seabed environment.
  2. Pulse Mode: Delivers short bursts of strong water flow, simulating natural tidal effects. The frequency can be adjusted using the knob (11 levels).
  3. Tidal Mode: Mimics the rise and fall of tides, creating a dynamic water flow experience. The frequency can be adjusted using the knob (11 levels).
  4. Turbulent Mode (Random): Generates a complex and multi-directional water flow, simulating ocean turbulence for a more natural feel.
Illustrations of four wave-making modes: Pulse wave, Tidal Swell, Constant wave, and Random Mode
Figure 7: Wave-making Modes

Feeding Mode

Press the 'F' button once to activate the Feeding Mode. The pump will pause for 10 minutes, providing a calm environment for feeding your corals or fish without disturbance. The pump will automatically resume its previous mode after 10 minutes.

Adjustable Dual Outlets

The wave maker features 360-degree adjustable dual outlets. You can independently rotate the front and rear sections of the pump to direct the water flow in different directions, allowing for precise customization of your aquarium's water movement.

Diagram illustrating the 360-degree adjustable dual outlets of the wave maker
Figure 8: 360-Degree Adjustable Dual Outlets

Crossflow Technology

Unlike traditional wave pumps that create a point-focused flow, the MagTool Crossflow Wave Maker utilizes a wider water outlet to generate a horizontal, broad water flow. This design minimizes dead spots and ensures comprehensive water circulation, authentically simulating natural ocean currents.

Diagram showing the wide, horizontal water flow pattern created by the cross-flow wave maker in an aquarium
Figure 9: Cross-Flow Water Movement
Visual comparison of water flow distribution between a crossflow wave maker (top) and a traditional wave maker (bottom), highlighting reduced dead spots with crossflow
Figure 10: Crossflow vs. Traditional Wave Maker Flow Comparison

7. Maintenance

Regular maintenance ensures optimal performance and longevity of your wave maker:

  • Cleaning the Pump: Unplug the power adapter before cleaning. Carefully remove the wave maker from the aquarium. Disassemble the pump housing and impeller. Clean any algae, debris, or calcium buildup from the impeller and inside the pump housing using a soft brush and warm water. Avoid using harsh chemicals.
  • Controller and Cables: Keep the controller dry and clean. Periodically inspect the power cord and connections for any signs of damage or wear.
  • Reassembly: Ensure all parts are dry and correctly reassembled before placing the pump back into the aquarium and plugging it in.

Silent Operation Features

The MagTool wave maker is designed for silent operation using sine wave technology and features shock-absorbing rubber supports. If you notice increased noise, check for debris in the impeller or ensure the rubber supports are properly seated.

Close-up of the rubber shock-absorbing support on the wave maker for silent operation
Figure 11: Silent Operation Design with Rubber Support

8. Troubleshooting

ProblemPossible CauseSolution
Pump not turning onNo power, loose connection, faulty adapterCheck power outlet, ensure all connections are secure, try a different outlet.
Weak or no water flowImpeller obstructed, pump dirty, incorrect settingsUnplug and clean the impeller and pump housing. Adjust flow intensity settings on the controller.
Excessive noiseDebris in impeller, improper mounting, worn impellerUnplug and clean the impeller. Ensure the pump is securely mounted and rubber supports are in place. If noise persists, the impeller may need replacement.
Controller display is offNo power, loose connection to controllerCheck power adapter connection to controller and wall outlet.

9. User Tips

  • Start Gradually: When first introducing the wave maker or after significant changes, start with lower flow settings and gradually increase to allow your aquarium inhabitants to acclimate.
  • Observe Livestock: Pay attention to your fish and corals. If they appear stressed or are struggling against the flow, reduce the intensity or adjust the direction.
  • Experiment with Modes: Different aquariums and inhabitants may benefit from different flow patterns. Experiment with Constant, Pulse, Tidal, and Turbulent modes to find what works best for your setup.
  • Placement is Key: Experiment with the placement of the wave maker and the direction of its adjustable outlets to eliminate dead spots and ensure even circulation.
  • Regular Water Changes: While the wave maker improves circulation, it does not replace the need for regular water changes and proper filtration.

10. Warranty and Support

MagTool products are manufactured to high-quality standards. For any technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact your retailer or the manufacturer's customer support. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.