PowMr BE24-N/BE48-N

Contents

PowMr 24V 48V Battery Equalizer Balancer User Manual

Models: BE24-N, BE48-N

1. Introduction

The PowMr Battery Equalizer is designed to maintain voltage balance across batteries connected in series, both during charging and discharging cycles. Battery voltage can become unbalanced due to variations in chemical composition, temperature, and self-discharge rates among individual cells. This imbalance can lead to premature battery failure, as some batteries may become overloaded while others are insufficiently charged.

This equalizer is an energy transfer type that compensates for voltage differences between batteries. It activates when a 10mV difference is detected between two batteries, facilitating current flow from the higher voltage battery to the lower voltage battery until equilibrium is reached. The device can be connected to your battery system continuously for 24 hours, providing automatic energy balance without manual intervention.

The PowMr Battery Equalizer is compatible with a wide range of battery types, including Lead-Acid (VRLA), Lithium Iron Phosphate (LiFePO4), Nickel-Cadmium (NiCd), and Nickel-Metal Hydride (NiMH) secondary batteries. It begins operation when the voltage exceeds 2.4V, making it suitable for single-cell battery systems ranging from 2.4V to 12V. A single equalizer can connect up to four batteries at a time. If fewer than four batteries are used, any extra cables should be left vacant, ensuring positive and negative terminals do not touch. The equalizer's function is unaffected by the battery connection method, whether in series or parallel.

PowMr BE24-N and BE48-N Battery Equalizers
Figure 1: PowMr BE24-N and BE48-N Battery Equalizers
48V Battery Equalizer in a solar panel setup, highlighting 'Doubles Battery Life'
Figure 2: 48V Battery Equalizer integrated into a solar panel system, emphasizing extended battery life.
Diagram illustrating battery voltage imbalance before and after using the equalizer
Figure 3: Illustration of battery voltage levels before and after equalization, demonstrating the product's balancing effect.

2. Specifications

Table 1: Technical Data for BE24-N and BE48-N
FeatureBE24-NBE48-N
Battery nominal voltage2*12V4*(2.4V/3.6V/6V/9V/12V)
Optimizing current0-5A0-10A
Quiescent current<3mA5mA(12V) 1.2mA(2.4V)
Dimensions78*78*28mm69*129*28 mm
ProtectionReverse polarity protectionReverse polarity protection
Low Voltage Disconnect10V1.8V

Additional Specifications (BE48-N)

  • Working Voltage: 4x0.4/3.6/6/12V
  • Compensate Current: 0-10A
  • Standby Current: <1.8mA
  • Temperature Range: -7.6°F - 131°F (-22°C - 55°C)
  • Dimension: 2.44 × 4.88 × 1.06 inches (62 × 124 × 27 mm)
  • Protection: Reverse polarity protection
  • Supported Battery Types: Lead-Acid (Sealed, AGM, Flooded, Gel, Calcium), Lithium Battery, Nickel Cadmium Secondary Batteries, Nickel-Metal Hydride Secondary Batteries
Technical specifications table and wiring diagrams for 4x12V series and 8 batteries 2P4S
Figure 4: Detailed technical specifications and example wiring diagrams for 4x12V batteries in series and 8 batteries in a 2P4S configuration.

3. Setup and Installation

Follow these steps carefully to install your PowMr Battery Equalizer:

  1. Connect the red cable to the positive (+) pole of the battery.
  2. Connect the black cable to the negative (-) pole of the battery.
  3. Connect the batteries according to the desired configuration (series or parallel) as shown in the diagrams below.
  4. For the BE48-N model, the white cable should connect to either the negative pole of Battery B or the positive pole of Battery A, specifically the pole that connects Battery A and Battery B in series.
  5. If there are extra cables (e.g., if using fewer than 4 batteries with a BE48-N), ensure they are left vacant and do not short circuit by touching other terminals.

Important Safety Note:

  • Always connect all positive (+) poles first, and then all negative (-) poles to avoid accidental short circuits.
  • Ensure no terminals touch each other during installation.
Detailed wiring diagrams for 24V, 36V, and 48V battery packs
Figure 5: Wiring diagrams for 24V, 36V, and 48V battery packs, illustrating proper connections for the equalizer.
Product packaging, user manual, and various wiring diagrams for 24V, 36V, and 48V battery packs
Figure 6: Overview of product components including the equalizer, packaging, user manual, and various battery pack wiring examples.

4. Operation

Once correctly installed, the PowMr Battery Equalizer operates automatically. It continuously monitors the voltage of the connected batteries and initiates balancing when a voltage difference of 10mV is detected between any two batteries.

LED Indicators (BE24-N)

The BE24-N model features LED indicators to show the battery charge status and balancing activity:

  • Charge Status: LEDs indicate 100%, 75%, 50%, and 25% charge levels.
  • Balancing Activity: LEDs labeled 'A' and 'B' indicate which battery is being balanced.
Close-up of the BE24-N Battery Equalizer with LED indicators
Figure 7: Front view of the BE24-N Battery Equalizer showing LED indicators for charge status and balancing activity.

LED Indicator Behavior (BE48-N)

The BE48-N model uses LEDs to indicate voltage conditions and balancing status:

  • When Battery A or Battery B is lower than 10V:
    • If Battery A is lower than 10V: LED A is ON, LED B is OFF.
    • If Battery B is lower than 10V: LED B is ON, LED A is OFF.
    • If both Battery A and Battery B are lower than 10V: LED A and LED B are both ON.
  • When Battery A or Battery B is higher than 10V:
    • If Battery A voltage is higher than Battery B: LED A is ON, LED B is OFF.
    • If Battery B voltage is higher than Battery A: LED B is ON, LED A is OFF.
    • If Battery A and Battery B are the same voltage: LED A and LED B are both OFF.
Diagrams showing LED indicator behavior based on battery voltage differences (lower/higher than 10V)
Figure 8: Visual guide to BE48-N LED indicator states based on battery voltage conditions.

The equalizer will automatically maintain the system's energy balance, requiring no further manual adjustments after proper installation.

Video 1: Product overview and demonstration of the PowMr Battery Equalizer.

5. Maintenance

The PowMr Battery Equalizer is designed for automatic operation and requires minimal maintenance. However, regular checks of your overall battery system are recommended to ensure optimal performance and longevity.

  • Visual Inspection: Periodically inspect the equalizer and its connections for any signs of damage, corrosion, or loose wiring.
  • Cleanliness: Keep the equalizer free from dust, dirt, and moisture to prevent overheating or malfunction.
  • Battery Health: While the equalizer helps maintain balance, it's good practice to monitor individual battery health and replace any failing batteries as needed.

6. Troubleshooting

If you encounter issues with your PowMr Battery Equalizer, consider the following:

  • No LED Activity: Ensure all connections are secure and correct. Check if the battery voltage is above the minimum operating threshold (2.4V).
  • Persistent Imbalance: If the batteries remain significantly unbalanced despite the equalizer operating, check the individual health of each battery. A severely degraded battery may prevent effective equalization.
  • Reverse Polarity Protection: The equalizer features reverse polarity protection. If connected incorrectly, it will not operate, preventing damage. Correct the wiring if this occurs.
  • Low Voltage Disconnect: The equalizer has a low voltage disconnect feature (10V for BE24-N, 1.8V for BE48-N). If battery voltage drops below this threshold, the equalizer may stop operating to protect the batteries.

7. User Tips

  • For optimal performance, ensure all batteries in a series string are of the same type, age, and capacity.
  • While the equalizer works automatically, occasional manual voltage checks of individual batteries can help confirm system health.
  • Consider the BE48-N for systems requiring balancing across more varied battery voltages (2.4V to 12V per cell) or higher optimizing currents.

8. Warranty and Support

This PowMr Battery Equalizer comes with a 2-year warranty from the date of purchase, as indicated on the product image.

For technical support, inquiries, or warranty claims, please contact PowMr directly:

  • Manufacturer: SHENZHEN HEHEJIN INDUSTRIAL CO., LTD
  • Address: Room E, 10th Floor, Building A, Rongde International, Henggang Street, Longgang District, Shenzhen, Guangdong, China 518116
  • Website: https://powmr.com
  • E-mail: support@powmr.com

A detailed user manual in PDF format is also available for download: PowMr Battery Equalizer User Manual (PDF)

9. Statement of Compliance

Disclaimer

⚠ WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.