GODIAG HKSO676

Contents

GODIAG ECU GPT Boot AD Connector User Manual

For ECU Reading, Writing, and Programming

1. Introduction

The GODIAG ECU GPT Boot AD programming adapter is a versatile tool designed to facilitate reading and writing of Engine Control Unit (ECU) data. It supports various methods including OBD2 Bench, GPT Bench (without disassembling the ECU), and Boot method (requiring ECU disassembly). This adapter is compatible with J2534 devices such as PCMFlash, Openport 2.0, FoxFlash, and FC200, providing a flexible solution for automotive diagnostics and programming professionals.

The product is engineered with safety in mind, featuring a short-circuit-proof BOOT resistance board connection line to protect the ECU during operation.

2. Product Features

  • ECU Dedicated Connection Terminal: Provides specific terminals for secure ECU connections.
  • Manual Ignition Power Control: Allows for manual control over the ignition power supply.
  • Labeled ECU Interface Cable: Ensures easy and correct wiring with clearly marked cables.
  • ECU Conversion to OBD2 Mode: Supports reading and writing data via OBD2 mode.
  • Comprehensive Pin Support: Supports RESET, BOOT, CNF1, GPT1, GPT2, 5V, 3.3V, VPP, and GND pins.
  • Automatic Ignition Power Supply Control: Compatible with PCMFlash for automatic control of ignition power.
  • ECU Opening BOOT Method: Facilitates data reading and writing using the BOOT method.
  • CANbus Resistor Switch: Equipped with a switch to freely select the 120Ω resistor for CANbus communication.
  • GPT Data Read/Write without Disassembly: Supports GPT method for data operations without needing to open the ECU.
  • BOOT Resistance Board Connecting Cable: Includes an anti-lost resistor design for the BOOT resistance board.
Diagram illustrating the 10 key features of the GODIAG ECU GPT Boot AD Adapter.
Figure 1: Key Features of the GODIAG ECU GPT Boot AD Adapter.
Close-up of the BOOT resistance board showing resistor values and connection points.
Figure 2: BOOT Resistance Board with Resistor Values (1KΩ, 120Ω, 100Ω, 5.8KΩ).

3. Package Contents

The GODIAG ECU GPT Boot AD Connector package includes the following items:

  • 1 x GODIAG ECU GPT Boot AD Adapter
  • 8 x Soft Silicone Wires
Contents of the GODIAG ECU GPT Boot AD Connector package, including the adapter, cables, and OBD2-DB25 connector.
Figure 3: Package Contents of the GODIAG ECU GPT Boot AD Connector.

4. Setup and Connection

The GODIAG ECU GPT Boot AD adapter can be connected in various configurations depending on the J2534 device and the ECU programming method (OBD2 Bench, GPT Bench, or Boot mode).

4.1 General Connection Overview

The adapter typically connects to a J2534 device, which then connects to a computer running the programming software. The adapter itself connects to the ECU via dedicated terminals and wiring. Ensure all connections are secure before proceeding.

Table illustrating different J2534 devices, their connection methods, and compatible dongle software.
Figure 4: Connection Methods for GODIAG ECU GPT Boot AD with J2534 Devices.

4.2 Specific Wiring Diagrams

Below are examples of wiring diagrams for specific ECU types. Always refer to the specific pinout for your ECU model to ensure correct connections.

Wiring diagram for SIMOS 8.10 [TC1796 INT.F.] - Audi ECU, showing connections for +12V, GND, CAN H, and CAN L.
Figure 5: Wiring Diagram for SIMOS 8.10 [TC1796 INT.F.] - Audi ECU.
Wiring diagram for MED17.5 ECU, showing connections for +12V, Can H, Can L, Gnd, S1, and S2.
Figure 6: Wiring Diagram for MED17.5 ECU.

4.3 Video Guide: Reading Hyundai SIM2K ECU

Watch this video for a step-by-step guide on how to use the GODIAG ECU GPT Boot AD with SM2 and GT100+ to read a Hyundai SIM2K ECU.

Video 1: How to use GODIAG ECU GPT Boot AD with SM2 and GT100+ to read Hyundai SIM2K ECU.

5. Operating Instructions

This section outlines the general procedure for reading ECU data using the GODIAG ECU GPT Boot AD adapter and PCMFlash software. Always ensure your J2534 device drivers are correctly installed and updated.

  1. Connect Components:
    • Connect the J2534 device (e.g., SM2 PRO) to your computer via USB.
    • Connect the OBD2-DB25 cable to the J2534 device.
    • Connect the GODIAG ECU GPT Boot AD adapter to the ECU Connector (e.g., GODIAG GT100+).
    • Connect the multi-pin wiring harness from the GODIAG ECU GPT Boot AD to the ECU according to the specific ECU's pinout diagram (refer to Figures 5 and 6 for examples).
  2. Power On: Turn on the power to the ECU Connector (e.g., GODIAG GT100+).
  3. Manual Mode Activation: Press the "MNL" button on the Godiag ECU GPT Boot AD to activate manual control.
  4. Launch Software: Open the PCMFlash software on your computer.
  5. Select ECU Type: In PCMFlash, select the appropriate ECU type (e.g., "Kia/Hyundai 2.0, 2.4, (SIM2K-140)" for Hyundai SIM2K ECU).
  6. Initiate Reading: Click the "Read" button in the PCMFlash software. Follow any on-screen prompts, such as turning ignition ON/OFF.
  7. Save Data: After successful reading, save the data file to your desired location on the computer.

6. Specifications

AttributeValue
Brand NameGODIAG
Model NumberHKSO676
OriginMainland China
CertificationCE
Package Length10 cm
Package Width8 cm
Package Height6 cm
Package Weight0.3 kg

7. Troubleshooting

  • Connection Issues: Ensure all cables are securely connected to the adapter, J2534 device, and ECU. Verify the correct pinout for your specific ECU model.
  • Software Not Recognizing Device: Check that the J2534 device drivers are installed correctly on your computer. Restart the computer and the programming software.
  • Reading/Writing Errors: Ensure the ECU is receiving stable power. Verify that the correct ECU type and protocol are selected in the programming software. If using the BOOT method, confirm the BOOT resistance board is correctly connected.
  • Power Indicator Lights: Observe the power indicators on the GODIAG ECU GPT Boot AD and the ECU Connector (if applicable) to ensure proper power supply.

8. User Tips

  • Double-Check Pinouts: Always verify the ECU pinout diagram for your specific vehicle and ECU model before making any connections to prevent damage.
  • Stable Power Supply: Ensure a stable and sufficient power supply to both the ECU and the programming tools to avoid interruptions during critical operations like reading or writing.
  • Software Updates: Keep your J2534 device drivers and programming software (e.g., PCMFlash) updated to the latest versions for optimal performance and compatibility.
  • Backup Data: Before performing any writing operations, always create a backup of the original ECU data.

9. Warranty and Support

For technical support, troubleshooting assistance, or warranty inquiries, please contact the manufacturer or your authorized dealer. Keep your purchase receipt and product serial number handy for faster service.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.