HWATEL Universal 6-Band Repeater Signal Amplifier

Contents

HWATEL Universal 6-Band Cellphone Mobile Network Booster

Model: Universal 6-Band Repeater Signal Amplifier

Professional Mobile Signal Booster Solutions

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your HWATEL Universal 6-Band Repeater Signal Amplifier. This device is designed to amplify cellphone signals across 2G, 3G, 4G, and 5G networks, supporting multiple frequency bands to improve both data and voice communication.

HWATEL Universal 6-Band Repeater Signal Amplifier with antennas
HWATEL Universal 6-Band Repeater Signal Amplifier and antenna components.

2. Packing List

Please check the contents of your package against the list below:

Contents of the HWATEL Signal Booster package
Visual representation of items included in the box.
  • Booster Unit: The main signal amplifier.
  • Power Adaptor: For powering the booster unit.
  • LOG Antenna (Outdoor): 45cm, 18dB gain, N Female connector. Designed for directional signal reception from 600-4000MHz.
  • Panel Antenna (Indoor): 9-12dB gain, with 2M RG58 Cable and N Male connector. Designed for broadcasting signal indoors from 600-4000MHz.
  • 10 Meter Cable: HWATEL Original RG-58, N Male-N Male connectors, for connecting outdoor antenna to booster.

3. Specifications

FeatureDescription
TypeModem Cable (Signal Booster)
Frequency Bands700MHz (Band 28) for 4G+
850MHz (Band 5) for 2G CDMA, 4G LTE
900MHz (Band 8) for 2G CDMA, 4G LTE
1800MHz (Band 3) for 4G LTE data
2100MHz (Band 1) for 3G WCDMA UMTS
2600MHz (Band 7) for 4G LTE plus
Gain70 ± 3 dB
Coverage Area500~1000 Square Meters
FeaturesALC (Automatic Level Control)
Intelligent Display (shows outdoor level, indoor level, no signal notification, self-exciting instructions)
Assembly RequiredYes
CertificationsCE, FCC, RoHS
Package DimensionsLength: 35 cm, Width: 25 cm, Height: 19 cm
Package Weight2.561 kg
Frequency band compatibility table for various countries and carriers
Table showing 6-band booster compatibility with carriers in Israel, Brazil, Australia, New Zealand, South Korea, and Japan.
Frequency band usage in Australia
Detailed frequency band usage for Telstra, Optus, and Vodafone in Australia.

4. Setup and Installation

Proper installation is crucial for optimal performance of your signal booster. Follow these steps carefully.

Overall installation diagram for the signal booster system
Diagram illustrating the complete installation process from outdoor antenna to indoor antenna.

4.1. Step 1: Find the Position with the Strongest Signal

Finding the strongest signal position for the outdoor antenna is the most important step. This location is typically above the roofline, on the side of the structure facing the nearest cellular tower, and positioned as high as practical to ensure a clear line of sight. Optimal placement allows the antenna to effectively “see” the serving cell tower, minimizing obstructions and maximizing signal strength and stability.

Measure Signal Strength:

Use a mobile device to measure the signal strength. The coverage area is directly dependent on the strength of the incoming signal received by the outdoor antenna. If the outdoor signal is less than 2 bars, the coverage area will be limited. If the outdoor signal is less than 1 bar, the booster may not work effectively.

  • For iPhone: Dial *3001#12345#* then press the call button. Choose 'All Metrics', then 'Serving Cell Info'. Check 'Band Info', 'RSRP', and 'SINR'.
  • For Android: Download and install a signal measurement app like "Network Cell Info Lite", "Cellular-Pro", or "Cellular-Z". Check 'Band', 'RSRP', and 'SINR'.
Screenshots of signal strength measurement on iPhone and Android devices
Examples of signal strength measurement interfaces on mobile phones.

4.2. Step 2: Install the Outdoor Antenna

Mount the outdoor antenna at the location identified in Step 1. Ensure it is positioned above the roofline and at the highest practical elevation. Verify that the installation site provides a minimum clearance radius of 3 meters, free from physical obstructions and other radiating or transmitting elements that may cause interference.

Raising the outdoor antenna or aligning it directly toward the serving mobile signal tower should result in an increase in received signal strength (RSRP), ideally reaching its optimal maximum level.

Diagram showing outdoor antenna placement relative to a cell tower and booster
Outdoor antenna installation diagram, showing optimal placement and signal path.

IMPORTANT: Adjust the direction of the outdoor antenna and continuously monitor the indoor signal with your cellphone to achieve optimal signal strength.

Comparison of LOG antenna vs Omni antenna and different LOG antenna sizes
Guidance on choosing an outdoor antenna: LOG antennas are directional and provide more range than Omni antennas.

4.3. Step 3: Install the Indoor Antenna

The provided panel antenna(s) should be mounted facing the area where signal coverage is required. It is essential that they are not directed toward the outdoor antenna.

ALERT! During indoor antenna installation, you must ensure that the indoor antenna is positioned far away from the outdoor antenna. They should be separated by a solid wall and installed back-to-back to maintain adequate isolation. Failure to maintain proper separation may result in loopback or signal noise. In such cases, the cellphone may indicate a strong or fluctuating signal; however, calls may still drop and data speeds may remain low.

How to avoid loopback:

  • Outdoor and indoor antennas should be separated by two walls.
  • Outdoor and indoor antennas should be installed back-to-back.
  • Maintain a vertical difference of over 13 feet between antennas.
  • Maintain a horizontal distance of over 30 feet between antennas.
Diagrams illustrating correct and incorrect indoor and outdoor antenna placement to avoid signal loopback
Visual guide for proper indoor and outdoor antenna separation to prevent signal interference.

4.4. Step 4: Install the Signal Booster

When positioning the booster, select a location near a functional AC power outlet. Do not expose the signal repeater to excessive heat, direct sunlight, moisture, or sealed airtight enclosures.

  1. Connect the outdoor antenna cable to the port labeled “Outside” or “BTS” on the booster and tighten the connection securely.
  2. Connect the cable from the indoor antenna to the port labeled "Inside” or “MS” on the booster and tighten the connection securely.
  3. Connect the AC power adaptor cord to the signal booster to power on the booster.

IMPORTANT: Adjust the indoor antenna and continuously monitor the indoor signal with your cellphone to ensure adequate coverage throughout all rooms.

5. Operating Instructions

Once the booster is installed and powered on, it will automatically begin amplifying the signal. The intelligent display on the booster will show the outdoor signal level, indoor signal level, and provide notifications for 'no signal' or 'self-exciting' (loopback) conditions.

Verifying Signal Improvement:

Use your mobile phone's signal strength measurement feature (as described in Section 4.1) to observe the improvement in 2G, 3G, and 4G signal strength after the booster is active. You should see a significant increase in dBm and asu values, indicating a stronger signal.

Video demonstrating the improvement in 2G/3G and 4G signal strength on a mobile phone after the HWATEL signal booster is turned on.

6. Maintenance

  • Keep Clean: Regularly wipe the booster unit and antennas with a dry, soft cloth to prevent dust accumulation.
  • Environmental Conditions: Ensure the booster is not exposed to excessive heat, direct sunlight, moisture, or sealed airtight enclosures.
  • Check Connections: Periodically inspect all cable connections to ensure they are secure and free from corrosion.
  • Antenna Alignment: If signal performance degrades, re-check the alignment of both outdoor and indoor antennas.

7. Troubleshooting

ProblemPossible CauseSolution
No signal or weak signal after installationOutdoor antenna not receiving strong enough signal; incorrect outdoor antenna direction; signal loopback (indoor and outdoor antennas too close).Re-evaluate outdoor antenna placement and direction (Step 1 & 2). Ensure clear line of sight to cell tower. Increase separation between indoor and outdoor antennas (Step 3).
Fluctuating signal or dropped callsSignal loopback (insufficient isolation between antennas).Increase physical separation between indoor and outdoor antennas. Ensure they are separated by solid walls and meet the recommended vertical/horizontal distances (Step 3).
Booster not powering onPower adapter not connected; faulty power outlet.Check power adapter connection to booster and wall outlet. Test the outlet with another device.
"No Signal" notification on displayOutdoor antenna not detecting any usable signal.Adjust outdoor antenna direction, try different mounting locations, or ensure it's facing the nearest cell tower.

8. User Tips

  • Regional Compatibility: Before purchasing, verify that the booster's supported frequency bands (700MHz, 850MHz, 900MHz, 1800MHz, 2100MHz, 2600MHz) are compatible with your local mobile carriers and network types (2G, 3G, 4G, 5G). Refer to the frequency band tables in the specifications section.
  • Optimal Placement is Key: Many users report significant improvements when the outdoor antenna is carefully positioned for the strongest possible signal and adequate separation is maintained between indoor and outdoor antennas. Take your time with the initial setup.
  • Monitor Signal Strength: Use a signal strength app on your phone during installation to fine-tune antenna positions for the best results.

9. Warranty and Support

For any issues while installing or operating your cell phone signal booster, please contact the HWATEL technical support team through the following channels:

  • Company: HWATEL Technology Co., Ltd
  • Address: Bldg 21, FengZeYingHe, Shangdi National High-Tech Park, Beijing, China, 100084
  • Website: www.hwatel.com
  • Email: info@hwatel.com, hwatel@foxmail.com
  • Phone Number: +86-18618303017
  • WhatsApp: +86-18618303017

For a downloadable PDF version of this manual, please visit the product page or contact support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.