1. Product Overview
The ANDELI MIG-270 is a versatile 4-in-1 multi-process synergic inverter welding machine designed for various welding applications. It supports Gas MIG, Flux MIG (gasless), Lift TIG, and MMA (ARC) welding modes. This machine features a large LED digital display for easy parameter reading and adjustment, and is suitable for both beginners and experienced welders.

Figure 1: Front view of the ANDELI MIG-270 welding machine.

Figure 2: ANDELI MIG-270 highlighting its 4-in-1 multi-process capabilities.
2. Safety Information
Always read and understand all safety precautions before operating the welding machine. Failure to follow safety guidelines can result in serious injury or death.
- Wear appropriate personal protective equipment (PPE), including welding helmet, gloves, and protective clothing.
- Ensure proper ventilation to avoid inhaling welding fumes.
- Keep a fire extinguisher nearby.
- Do not operate the machine in wet conditions.
- Ensure the machine is properly grounded.
- Disconnect power before performing any maintenance or adjustments.
3. Setup Instructions
3.1 Unpacking and Inspection
- Carefully remove the welding machine and all accessories from the packaging.
- Inspect the machine for any signs of damage during transit. If damaged, contact your supplier immediately.
- Ensure all components listed in the packing list are present.
3.2 Power Connection
The MIG-270 supports dual voltage operation (110V/220V). Ensure the correct power supply is used for your region and application.

Figure 3: The MIG-270 supports dual voltage (110V/220V).
3.3 Connecting Welding Accessories
Refer to the schematic diagram below for proper connection of welding accessories for each mode.

Figure 4: Schematic diagram of wiring for different welding modes.
- MIG Welding (with gas): Connect the MIG torch to the positive (+) terminal and the ground clamp to the negative (-) terminal. Connect the gas hose to the gas inlet.
- Flux MIG Welding (without gas): Connect the MIG torch to the negative (-) terminal and the ground clamp to the positive (+) terminal. No gas connection is required.
- MMA Welding (Stick): Connect the MMA holder to the positive (+) terminal and the ground clamp to the negative (-) terminal.
- Lift TIG Welding: Connect the TIG torch to the negative (-) terminal and the ground clamp to the positive (+) terminal. Connect the gas hose to the gas inlet on the TIG torch.
3.4 Wire Spool Installation (MIG/Flux MIG)
The machine is compatible with 1KG and 5KG welding wire spools, and supports 0.8mm/1.0mm wire diameters.
- Open the wire feeder compartment.
- Place the appropriate wire spool onto the spindle.
- Thread the welding wire through the wire feeder mechanism, ensuring it passes through the correct groove for the wire diameter (0.8mm or 1.0mm).
- Close the wire feeder compartment.

Figure 5: Wire spool and wire diameter compatibility.
3.5 MIG Torch Components
Familiarize yourself with the MIG torch components for proper operation and maintenance.

Figure 6: MIG torch components including shield cup, contact tip, tip holder, and goose neck bend.
4. Operating Instructions
4.1 Power On and Mode Selection
- Turn on the main power switch located on the rear of the machine.
- The large LED display will illuminate.
- Use the mode selection button (often indicated by a recycle-like icon) to cycle through the available welding modes: Flux MIG, Syn MIG, Man MIG, and Stick/TIG.

Figure 7: Digital display screen and control interface.
4.2 Parameter Adjustment
- Synergy Adjustment (Flux MIG / Syn MIG): For Flux MIG and Synergic MIG modes, the machine automatically adjusts wire speed and voltage based on the selected current and plate thickness. Use the control knob to adjust the current (A) and the machine will automatically set the corresponding voltage (V) and recommended plate thickness (mm).
- Manual Adjustment (Man MIG): In Manual MIG mode, the current (A) and voltage (V) can be controlled independently using the control knob.
- MMA / Lift TIG: Adjust the current (A) as needed for your electrode or TIG application.
4.3 Welding Process
The ANDELI MIG-270 is suitable for welding various materials including Carbon Steel, Square Tube, Galvanized Plate, and Angle Steel.

Figure 8: Applicable materials and weld types.
Video 1: Demonstration of the ANDELI MIG-270 welding machine in various modes.
5. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welding machine.
- Cleaning: Periodically clean the machine's exterior with a dry, soft cloth. Use compressed air to blow out dust from the cooling vents.
- Connections: Regularly check all electrical connections, including power cables, welding cables, and gas hoses, for tightness and damage.
- Wire Feeder: Inspect the wire feeder rollers for wear and ensure they are clean and free of debris. Replace worn rollers as needed.
- MIG Torch: The split welding gun design allows for easier disassembly and maintenance. Regularly clean the contact tip, nozzle, and gas diffuser. Replace consumables as they wear out.
- Cooling System: The machine uses fan cooling. Ensure the fan intake and exhaust are not obstructed to maintain proper airflow.
6. Troubleshooting
- No Arc/Poor Weld:
- Check all connections (power, ground, torch).
- Ensure correct welding mode and parameters are selected for the material and wire/electrode.
- Verify wire feed speed and voltage settings.
- For Gas MIG, check gas supply and flow rate.
- For Flux MIG, ensure correct polarity (torch negative, ground positive).
- Machine Not Powering On:
- Check power supply and circuit breaker.
- Ensure the power cable is securely connected.
- MMA Welding Issues at 110V: Some users report MMA welding performing better or exclusively at 220V. If experiencing issues with MMA at 110V, verify the machine's capability for MMA at that voltage or switch to a 220V supply if possible.
- Welder for Cutting: This machine is designed for welding, not cutting. For cutting applications, a dedicated plasma cutter or other cutting tools are required.
- TIG Welding Aluminum: The MIG-270 features Lift TIG, which is typically a DC TIG process. DC TIG is generally suitable for steel and stainless steel. For welding aluminum, an AC TIG machine is usually required.
7. Specifications

Figure 9: Detailed technical parameters.
| Item | Specification |
|---|---|
| Model Number | MIG-270 |
| Brand Name | ANDELI |
| Input Power | Single Phase 220V ±15% 50Hz (also supports 110V) |
| Rated Input Power (KW) | 7.2 |
| Rated Output Voltage (V) | 26.4 |
| Output Current Range (A) | 40-200 |
| No-Load Voltage (V) | 55 |
| Rated Duty Cycle (%) | 30 |
| Power Factor | 0.73 |
| Insulation Class | F |
| Protect Class | IP21S |
| Cooling Mode | Fan Cooling |
| Efficiency (%) | 80 |
| Weight (kg) | 7.1 |
| Dimensions (mm) | 455*180*300 |
| Wire Spool Compatibility | 1KG / 5KG |
| Wire Diameter Compatibility | 0.8mm / 1.0mm |
| Certification | CE |
8. User Tips
- The machine's clear LED display and unified adjustment mode make it very user-friendly, even for those new to welding.
- Utilize the synergy adjustment feature in Flux MIG and Syn MIG modes for automatic optimization of wire speed and voltage, simplifying parameter setup.
- For Gas MIG, the recommended plate thickness range is 0.03"-0.24".
- For Flux MIG (gasless) thin sheet drag welding, MIG solid wire of 0.030"/0.035" is recommended.
- When using MMA (Stick) welding, 2.5mm electrodes are commonly available and compatible.
9. Warranty and Support
For any technical assistance, warranty claims, or support inquiries, please contact the ANDELI Official Store or your authorized dealer. Keep your purchase receipt as proof of purchase.