1. Introduction
The LILYGO® T-Display-S3-Pro is an advanced ESP32-S3 development board, serving as an upgraded version of the T-Display-S3. It integrates a larger 2.33-inch touch LCD and features the SY6970 chip for phone OTG capabilities. Designed for versatility, it comes in an ABS case and supports expansion with camera modules via POGOpin connectors. The board includes a built-in 3.8V 470mAh battery, ambient light and proximity sensors, two integrated QWIIC ports, and a battery power switch. An optional MPU9250 IMU module is also available.
2. Key Features
- Microcontroller: ESP32-S3R8 Dual-core LX7 microprocessor.
- Display: 2.33-inch Touch IPS TFT LCD with 222(H)RGB x 480(V) resolution, ST7796 drive chip, and SPI interface.
- Wireless Connectivity: Wi-Fi 802.11 and BLE 5 + BT mesh.
- Memory: 16MB Flash and 8MB PSRAM.
- USB: Supports USB OTG.
- Sensors: Integrated I2C Digital Light Sensor (LTR-553ALS-01) with ambient light (ALS) and proximity (PS) features. Optional MPU9250 IMU module.
- Expansion: POGOpin connectors for camera modules (OV5640/GC0308 optional) and two QWIIC ports.
- Power: Built-in 3.8V 470mAh battery with a power switch.
- Programming: Compatible with Arduino-IDE and MicroPython.
- Onboard Functions: Boot, Reset, I012, and I016 buttons.
- Voice Communication Kit (MVSR Board): Includes Microphone (MP34DT05-A), Vibration (PWM Motor), and Speaker I2S (MAX98357A).
3. Specifications
| Feature | Detail |
|---|---|
| Model Number | T-Display-S3-Pro |
| Brand Name | LILYGO |
| Chipset | ESP32-S3R8 Dual-core LX7 microprocessor |
| Display | 2.33-inch Touch IPS TFT LCD |
| Display Resolution | 222(H)RGB x 480(V) |
| Display Drive Chip | ST7796 |
| Display Interface | SPI |
| Flash Memory | 16MB |
| PSRAM | 8MB |
| Wireless Connectivity | Wi-Fi 802.11, BLE 5 + BT mesh |
| Programming Platform | Arduino-IDE, MicroPython, VS Code (MVSR Board) |
| USB Support | USB OTG (via SY6970 chip) |
| Digital Light Sensor | LTR-553ALS-01 (Ambient Light Sensor & Proximity Sensor) |
| Battery | 3.8V 470mAh@0.2C (onboard) |
| Dimensions (WxHxD) | 72mm x 18mm x 32mm |
| Package | Yes |
4. Setup Guide
4.1 Initial Power Up
- Charge Battery: Connect the T-Display-S3-Pro to a 5V USB power source using a USB-C cable. The onboard 3.8V 470mAh battery will begin charging.
- Power On: Locate the battery power switch on the side of the device and slide it to the 'ON' position. The display should light up.
4.2 Connecting to a Computer
To program or communicate with the T-Display-S3-Pro:
- Connect the device to your computer using a USB-C data cable.
- Your computer should recognize the device as a serial port. You may need to install appropriate USB drivers for ESP32-S3 if not automatically detected.
4.3 Development Environment Setup
The T-Display-S3-Pro supports development using Arduino-IDE and MicroPython. For detailed instructions and sample code, please refer to the official LILYGO GitHub repository:
Follow the instructions on the GitHub page to set up your preferred development environment and upload your first program.
5. Operation
5.1 Basic Interaction
- Touch Display: The 2.33-inch IPS TFT LCD is a capacitive touch screen. Interact with on-screen elements by tapping or swiping as programmed.
- Buttons: The device includes Boot, Reset, I012, and I016 buttons for various functions, typically used during programming or for specific application controls. Refer to your loaded firmware's documentation for specific button functionalities.
- SD Card: Insert a TF card into the designated slot for data storage or firmware updates, depending on your application.
- QWIIC Ports: Utilize the two integrated QWIIC ports for easy connection to compatible I2C sensors and modules without soldering.
5.2 Camera Module (Optional)
If your T-Display-S3-Pro includes a camera module (OV5640 or GC0308), ensure it is securely connected via the POGOpin interface. Software configuration will be required to enable and utilize the camera functionality within your application.
6. Maintenance
- Cleaning: Use a soft, dry cloth to clean the device. Avoid using liquids or abrasive cleaners.
- Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
- Battery Care: For optimal battery life, avoid fully discharging the battery frequently. If storing for extended periods, charge the battery to around 50%.
- Handling: Handle the device with care to prevent physical damage, especially to the display and exposed connectors.
7. Troubleshooting
- Device does not power on:
-
- Ensure the battery power switch is in the 'ON' position.
- Connect the device to a USB power source to check if the battery is charged.
- Verify the USB cable and power source are functional.
- Display is blank or unresponsive:
-
- Check power supply.
- If recently programmed, ensure your code initializes the display correctly.
- Perform a hard reset by pressing the Reset button.
- Computer does not detect the device:
-
- Try a different USB-C cable and USB port on your computer.
- Install or update the necessary USB-to-serial drivers for ESP32-S3.
- Ensure the device is powered on.
- Programming errors:
-
- Verify your development environment is correctly configured for the ESP32-S3.
- Check your code for syntax errors or incorrect pin assignments.
- Consult the LILYGO GitHub repository for common issues and solutions.
8. User Tips
- Camera Choice: If purchasing a camera version, consider the OV5640 camera for better performance, as some users found the GC0308 to be less effective.
- Expandability: The T-Display-S3-Pro is highly expandable. Explore connecting external modules like CC1101 for enhanced functionality.
- Care with Connectors: Exercise caution when handling internal connectors, especially the display cable. Repeated removal and insertion can be challenging and may lead to damage.
- Soldering: If you plan to solder to the board's protrusions or pin holes, ensure you have appropriate tools and experience to avoid damaging the board or case.
9. Warranty and Support
For technical support, documentation, and community resources, please visit the official LILYGO website or their GitHub repository. Information regarding product warranty and returns can typically be found on the seller's platform or by contacting LILYGO customer service directly.
LILYGO Official GitHub: https://github.com/Xinyuan-LilyGO/T-Display-S3-Pro