1. Product Introduction
The HiBy FD3 is a portable USB high-definition lossless audio decoder and headphone amplifier, designed to elevate your audio experience across various devices.
Key Features:
- Based on HiBy's self-developed USB audio system.
- Adopts dual ES9038Q2M decoding architecture, supporting up to DSD512 and PCM 768kHz decoding.
- Supports PhoneOut (PO) and Balanced analog audio output.
- Multi-system compatible: Windows 10, iOS, Android, Mac.
- Features a cable-interchangeable design for high adaptability.
- Functions as a computer sound card without requiring charging.
- All-metal body for durability and premium feel.
2. Setup
2.1 Connecting the Device
To use the HiBy FD3, connect it to your host device using a compatible USB Type-C cable. The FD3 draws power directly from the host device, requiring no separate charging.
- Host Devices: The FD3 can be connected to various devices including dedicated audio players, mobile phones, computers (Windows, Mac, Linux), and tablets.
- Cable: Ensure you use a USB cable with at least one Type-C end to connect to the FD3.
Warning:
- Some devices may have compatibility issues due to differences in systems and hardware.
- Certain mobile phones may require manual activation of the OTG (On-The-Go) function in their system settings for the FD3 to operate correctly.
2.2 System-Specific Setup
Windows Computer:
- Windows 10 (Build 1703 and later): The FD3 is generally plug-and-play, as these versions of Windows include a native driver. For an enhanced experience, especially for ASIO support, additional drivers can be installed. Refer to the full user manual PDF for driver installation instructions.
- Windows 7/8/10 (Earlier than Build 1703): These versions do not natively support the UAC2.0 protocol required by the FD3. Driver installation is necessary for proper functionality. Refer to the full user manual PDF for driver installation instructions.
Android Player, Mobile Phone or Tablet:
- Non-Exclusive Mode: Simply plug the FD3 into your Android device's USB port. If needed, enable the OTG function in your device's system settings.
- Exclusive Mode (via HiByMusic App):
- Download and install the HiBy Music app (HiByMusic) from your device's app store.
- Open the HiBy Music app.
- Swipe right to open the settings options.
- Navigate to 'Settings' and select 'HiBy Music exclusive USB output'.
- Enable the exclusive output option.
- Plug the FD3 into your phone. A prompt "Allow HiBy Music Use to access HiBy FD3" may appear; click 'Allow'.
Note: Not all Android devices may support the exclusive mode. If you encounter issues, contact your mobile phone manufacturer for confirmation.
iPhone or iPad Tablet (iOS):
iOS devices have native driver support for USB DACs. The FD3 can be used by directly connecting it to your iPhone or iPad via a compatible USB cable (e.g., USB-C to Lightning adapter if necessary).
Apple Computer (macOS):
macOS also includes native driver support. Connect the FD3 directly to your Mac via USB for plug-and-play operation.
Linux Distribution:
USB DAC support on Linux depends on the kernel configuration. While many distributions support USB sound card functions out-of-the-box, some may require compiling the kernel with specific options or using a third-party application to enable USB DAC functionality.
3. Operating Instructions
3.1 Physical Interfaces
The HiBy FD3 features the following interfaces:
- Right Side (from top to bottom):
- Power button
- LED indicator
- Volume Up (+)
- Play/Pause
- Volume Down (-)
- Bottom Side (from left to right):
- PO (Phone Out) - 3.5mm single-ended headphone output
- Type-C - USB input port
- BAL (Balanced) - 2.5mm balanced headphone output
- BAL (Balanced) - 4.4mm balanced headphone output
3.2 Button Functions
| Button | Function |
|---|---|
| Power button | Long press: Power on/off; Short press: Switch screen |
| Volume + | Increase volume |
| Play/Pause | Single tap: Play/Pause; Double tap: Previous track; Triple tap: Next track |
| Volume - | Decrease volume |
3.3 LED Indicator Status
The LED indicator on the HiBy FD3 provides visual feedback on the current playback status and sample rate:
- Red: Power on, no playback.
- RGB: DSD playback.
- Blue: Playback at 32-48 kHz.
- Green: Playback at 88.2-192 kHz.
- Orange: Playback at 352.8-768 kHz.
4. Maintenance
- Cleaning: Use a soft, dry cloth to clean the device. Avoid using harsh chemicals or abrasive materials.
- Storage: Store the FD3 in a cool, dry place away from direct sunlight and extreme temperatures.
- Handling: Handle the device with care to prevent drops or impacts that could damage internal components.
- Connectivity: Always ensure cables are connected firmly but gently to avoid damaging the ports.
5. Troubleshooting
- No Sound / Device Not Recognized:
- Ensure the FD3 is securely connected to the host device via the USB Type-C cable.
- Check if your mobile phone's OTG function is enabled (if applicable).
- For Windows computers, verify that the necessary drivers are installed, especially for older versions of Windows 10 or earlier operating systems. Refer to the official HiBy support for driver downloads.
- Confirm that the correct audio output device (HiBy FD3) is selected in your host device's sound settings.
- Distorted Audio / Poor Sound Quality:
- Ensure your audio files are not corrupted or of low quality.
- Check headphone connections and try different headphones to rule out faulty cables or headphones.
- Verify that the volume levels on both the FD3 and your host device are appropriately set and not excessively high, which could cause clipping.
- Device Overheating:
- It is normal for the FD3 to generate some heat during operation due to its high-performance decoding chip.
- If the device feels excessively hot, disconnect it and allow it to cool down. Ensure it is used in a well-ventilated area.
- Linux Compatibility Issues:
- If your Linux distribution does not recognize the FD3, you may need to ensure your kernel has USB sound card functions enabled or consider installing a third-party application for USB DAC support.
For more detailed troubleshooting steps and FAQs, please refer to the official HiBy support resources or the comprehensive user manual PDF.
6. Specifications
| Feature | Detail |
|---|---|
| Model Name | HiBy FD3 |
| Dimensions | 61.5 x 61.5 x 12.1 mm |
| Weight | 73 g |
| USB Receiver | CT7601PH |
| DAC Chipsets | Dual ES9038Q2M |
| Amplifier Chipsets | Dual ES9603Q |
| Audio Formats | DSD, APE, WAV, WMA, FLAC, AIFF, M4A, MP2, MP3, AAC, OGG, OPUS (Native DSD decoding) |
| DSD Sampling Frequencies | Up to 22.5792 MHz (DSD512) |
| PCM Sampling Frequencies | 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz, 352.8 kHz, 384 kHz, 705.6 kHz, 768 kHz |
| PCM Word Length | 16-bit, 24-bit, 32-bit |
| Inputs | USB Type-C |
| Outputs | 3.5 mm (Single-Ended), 2.5 mm (Balanced), 4.4 mm (Balanced) |
| Headphone Out (3.5mm) | Supports inline remote control, all headphones and mic'd headsets |
| Status Indication | RGB LED |
| Power Supply | Via USB port (no charging required) |
| Bluetooth | No |
| Wi-Fi | No |
| Material | All-metal body |
| Certification | CE |
6.1 Audio Performance Specifications
| Parameter | PO (3.5mm) | 2.5mm BAL | 4.4mm BAL |
|---|---|---|---|
| Test Condition | 32Ω loaded | ||
| Output Level | 1.65Vrms | 2.1Vrms | 2.1Vrms |
| Output Power | 85mW | 138mW | 138mW |
| THD+N | 0.0015% | 0.0013% | 0.0013% |
| Noise | 2uV | 3uV | 3uV |
| SNR | 118dB | 117dB | 117dB |
| Crosstalk Rejection | 66dB | 97dB | 97dB |
| Frequency Response (±3dB) | 20Hz-90kHz | 20Hz-90kHz | 20Hz-90kHz |
7. User Tips
- Microphone Support: The 3.5mm single-ended headphone output (PO) on the HiBy FD3 supports standard headphones, including those with an inline remote control and microphone.
- Volume Adjustment: Always adjust the volume to a low level on both the FD3 and your host device before playing audio, then gradually increase to a comfortable listening level to prevent potential hearing damage.
- Headphone Connection: It is recommended to avoid wearing headphones when plugging or unplugging them from the FD3 to prevent sudden, loud impact sounds.
- HiByMusic App: For the best audio experience on Android devices, utilize the HiByMusic app's exclusive HQ USB audio access mode. This can significantly improve sound quality by bypassing Android's native audio processing.
8. Warranty and Support
For detailed warranty information, technical support, and frequently asked questions, please refer to the official HiBy website or the comprehensive user manual PDF.
A detailed user manual in PDF format can be found here: HiBy FD3 User Manual (PDF).
For driver downloads and further assistance, visit the official HiBy support page.
9. Important Notes
- This product is powered by USB and consumes power from the connected host device (mobile phone, tablet, or computer).
- Due to the high-performance decoding chip, it is normal for the equipment to generate a certain amount of heat during use.
- Before plugging and unplugging headphones, it is recommended not to wear them to avoid possible instantaneous impact sounds.
- Always adjust the volume of the device to an appropriate position before listening to music to prevent excessive volume from damaging your hearing.