1. Introduction
The JIKONG Smart BMS (Battery Management System) JKBMS is an advanced system designed to manage and protect various battery types, including LiFePo4, Li-ion, and LTO. It features Bluetooth (BT) app connectivity, RS485, and CAN communication interfaces, along with active balancing capabilities to ensure optimal battery performance and longevity. This manual provides essential information for the safe and efficient use of your JKBMS.
Video: Overview of JIKONG Active Balance BMS features, including 24-hour detection, real-time automatic balancing, 0A~2A balanced current, higher balance efficiency, smart management via app, compatibility with different string numbers, and 6 major protections.
2. Package Contents
Verify that all items are present in your package:
- JIKONG Smart BMS Unit
- Operating Manual
- NTC Temperature Sensor (40cm)
- Switch (50cm)
- Wiring Harness (70cm)
- Pack Box
- Screws (4 pcs) - for some models
- Heating Cable (16cm) - for models with heating function
- CAN Cable (25cm) - for models with CAN interface

Image: JIKONG Smart BMS unit (model JK-BD4A8S4P) highlighting its function, BMS type, balancing current, battery strings, charge/discharge current, size, and battery type compatibility.

Image: Package contents for Smart BMS Black with AWG Cables (models BD6A20S10P, BD6A24S10P, BD6A20S12P, BD6A24S12P, BD6A20S15P, BD6A24S15P, B1A20S15P, B1A24S15P, B2A20S20P, B2A24S15P, B2A24S20P).

Image: Package contents for Smart BMS Grey without AWG Cables (models BD4A8S4P, B1A8S10P, B1A8S20P, B2A8S20P, B2A8S30P).

Image: Package contents for Smart BMS Black with AWG Cables (Heating) (models B2A20S20P-HC, B2A24S20P-HC).

Image: Package contents for Smart BMS Grey without AWG Cables (Heating) (models B1A8S10P-HC, B1A8S20P-HC, B2A8S20P-HC).
3. Setup and Installation
Follow these steps carefully to install and set up your JKBMS:
- Download App and Manual: Download the JIKONG BMS app from the APP STORE (iOS) or Google STORE (Android). The full instruction manual and protocol can be found at: https://github.com/JIKBMS/files/tree/main and https://github.com/syssi/esphome-jk-bms.
- Hardware Connection: Connect the BMS and battery pack according to the provided wiring diagram. Ensure that the last power cord (B+) is connected to the main positive pole of the battery. The total voltage of the battery pack must be greater than 20V (for default BMS) or 10V (for 4S BMS) before starting up.
- Activate BMS: Use the display activation button or an additional switch to activate the BMS unit.
- App Connection: Turn on GPS and Bluetooth on your mobile phone. Open the JIKONG BMS app, click on the top left corner to search for devices. Select your device name to connect. The default password is 1234.
- Initial Parameter Settings: For the first startup, you will need to set parameters. Enter the default password 123456. Set the correct number of battery strings and battery type (LiFePo4, Li-ion, or LTO).
- Verify Operation: After setting the parameters, return to the real-time status page in the app. Check the battery status. If no error message is prompted, the system is operating normally. In the app, blue font indicates the highest voltage, and red font indicates the lowest voltage.

Image: Detailed wiring diagram for connecting the JIKONG Smart BMS to a battery pack, motor/load, and charger. It illustrates the sampling cable connections for each battery string.

Image: JIKONG Smart BMS wiring scheme, illustrating connections for various battery string counts (e.g., 2S-24S) and the placement of the heating pad.

Image: Detailed view of the JKBMS interface ports, including NTC, CAN/RS485, GPS, Display, and Heating Cable connections, along with optional external accessories like a switch and LCD displays.
4. Operating Instructions
The JKBMS offers smart management and various operating modes to optimize battery performance and safety.
4.1. Mobile App Operation
The JIKONG BMS app allows real-time monitoring and parameter control:
- Monitor battery data in real-time.
- Modify related parameters (e.g., cell count, battery capacity, balance voltage).
- Control the BMS balance switch.
- Supports both Android and iOS systems.

Image: Smart BT APP interface displaying real-time battery data, settings, and control options for the JIKONG BMS.

Image: Mobile app interface for Bluetooth connection, showing device list, real-time battery status, and parameter settings.
4.2. Smart Energy Working Modes
The JKBMS supports different working modes:
- Storage Mode: In transportation, offline, or wireless transmission off mode, the BMS does not consume battery pack current.
- Normal Working Mode: When the charger is inserted in storage mode or off mode, the BMS immediately returns to normal working mode, and all protection, equalization, and communication functions return to normal working.
- Shutdown: To prevent the BMS from wasting power for a long time and damaging the battery pack, the BMS has an automatic shutdown voltage. The BMS automatically shuts down when a cell falls below the shutdown voltage.
- Standby Mode: When the battery pack is in a static state (no charge and discharge current and no equilibrium current), the BMS automatically enters standby state after a set time (1-30 days can be set).

Image: Flowchart explaining the different smart energy working modes of the JKBMS and their transition conditions.
4.3. Heating Function (if applicable)
For models equipped with the "Heat" function:
- The heating function is activated by detecting low battery temperature during charging. It uses the charger's status to control the heating.
- The heating interface requires an external heating film or charger.
- Connect the green cable to the heating film, and the red and black cables to the charger.
- The maximum heating power is 3A, and the maximum heating voltage is 100V.
Heating on condition:
- The battery temperature is lower than the low-temperature protection temperature for charging.
- When the heating film is connected for heating, the APP will activate heating, which will consume battery power.
- Heating through the charger is related to the protection board hardware and charger. Confirm technical status before ordering.
5. Maintenance
To ensure the longevity and optimal performance of your JKBMS and battery pack:
- Regularly check all wiring connections for tightness and corrosion.
- Monitor battery cell voltages and temperatures via the mobile app to identify any anomalies early.
- Keep the BMS unit clean and free from dust and moisture.
- Ensure proper ventilation around the battery pack and BMS to prevent overheating.
- Periodically update the BMS firmware if new versions are released by the manufacturer (check the app or manufacturer's website for updates).
6. Troubleshooting (FAQ)
Here are solutions to common issues you might encounter:
6.1. BMS Does Not Turn On
- Ensure that the last "B+" line of the cable has been correctly connected to the positive pole of the battery.
- Start up after charging and ensure that the charger voltage is greater than 4V of the battery pack voltage.
- Check whether the charger has voltage output.
6.2. Inaccurate Voltage Readings
- Measure the actual total voltage of the battery pack with a multimeter.
- Enter the measured total voltage into the "voltage calibration" setting on the parameter setting page in the app.
6.3. Inaccurate Current Readings
- The B- and P- terminals of the protection board use two 7AWG wires. Both must be connected in parallel; otherwise, it will lead to current error.
- Measure the actual current of the battery pack with a clamp meter.
- Enter the measured actual current into the "current calibration" setting on the parameter setting page. A larger actual current will result in higher calibration accuracy.
6.4. Inaccurate Capacity Readings
- An initial capacity estimated based on the monomer voltage when the protection board is first powered on may be inaccurate.
- After the protection board is discharged to the cut-off voltage and then fully charged, the capacity will be calibrated. Ensure the charging process is not interrupted during this calibration.
6.5. Designed String Number Inconsistent with Actual String Number
- Check whether the "unit quantity" in the parameter settings is set correctly in the app.
- If there is no voltage in two or more strings in the middle of the pack, check whether the acquisition cable has fallen off or is damaged.

Image: FAQ section providing troubleshooting steps for common JKBMS issues.
7. Specifications
The JIKONG Smart BMS JKBMS is available in various configurations. Key specifications include:
- Brand Name: smart jikong bms
- Type: LIFEPO4 Battery BMS
- Handware or Smart: SMART BMS
- Balance Function: Active Balanced BMS
- Charge and Discharge Port: Common Port BMS
- Usage Scenario: Power BMS, Energy Storage BMS, 3C Digital BMS
- Certification: CE, FCC, RoHS
- Function: Overcharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection
- Active Current: 0.4A-2A
- Battery Strings: 4S-24S
- Charge/Discharge Current: 40A-200A
- Accessory Function: BT/RS485/CAN/Heat
7.1. Dimensions

Image: Dimensions for BD6A series JKBMS models (74mm W x 116mm L x 17.6mm T).

Image: Dimensions for other JKBMS models (102mm W x 162mm L x 16.6mm T).

Image: Dimensions for B1A8S10P, B2A8S20P, B1A8S20P JKBMS models (136mm W x 153mm L x 17mm T).
7.2. Detailed Parameter Table (BD4A/BD6A Series)
| Item | Parameters | BD4A8S4P | BD4A17S4P | BD4A20S4P | BD4A24S4P | BD6A17S6P | BD6A20S6P | BD6A24S6P | BD6A17S8P | BD6A20S8P | BD6A24S8P |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Function | BT / Display supported | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
| BMS Type | Battery BMS | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
| Balancing Current | 0.4A | 0.4A | 0.4A | 0.4A | 0.4A | 0.6A | 0.6A | 0.6A | 0.8A | 0.8A | 0.8A |
| Battery Strings | 4S-8S | 4S-8S | 7S-17S | 7S-20S | 7S-24S | 8S-17S | 8S-20S | 8S-24S | 8S-17S | 8S-20S | 8S-24S |
| Balance method | Active balancer | Active balancer | Active balancer | Active balancer | Active balancer | Active balancer | Active balancer | Active balancer | Active balancer | Active balancer | Active balancer |
| Internal resistance | 0.5mΩ | 0.5mΩ | 0.5mΩ | 0.5mΩ | 0.5mΩ | 0.3mΩ | 0.3mΩ | 0.3mΩ | 0.3mΩ | 0.3mΩ | 0.3mΩ |
| Continuous Discharge Current | 40A | 40A | 40A | 40A | 40A | 60A | 60A | 60A | 80A | 80A | 80A |
| Continuous Charge Current | 40A | 40A | 40A | 40A | 40A | 60A | 60A | 60A | 80A | 80A | 80A |
| MAX Discharge Current (20s) | 80A | 80A | 80A | 80A | 80A | 120A | 120A | 120A | 160A | 160A | 160A |
| Interface | RS485 | RS485 | RS485 | RS485 | RS485 | RS485/CAN | RS485/CAN | RS485/CAN | RS485/CAN | RS485/CAN | RS485/CAN |
| Interface (CAN/Heat) | - | - | - | - | - | CAN/Heat Port | CAN/Heat Port | CAN/Heat Port | CAN/Heat Port | CAN/Heat Port | CAN/Heat Port |
| Dimension (mm) | 121.5x93x17.6 | 121.5x93x17.6 | 121.5x93x17.6 | 121.5x93x17.6 | 121.5x93x17.6 | 162x102x20.4 | 162x102x20.4 | 162x102x20.4 | 162x102x20.4 | 162x102x20.4 | 162x102x20.4 |
| Wiring diagram | Same Port | Same Port | Same Port | Same Port | Same Port | Same Port | Same Port | Same Port | Same Port | Same Port | Same Port |
| Single cell voltage | 1.5V-4.5V | 1.5V-4.5V | 1.5V-4.5V | 1.5V-4.5V | 1.5V-4.5V | 1.5V-4.5V | 1.5V-4.5V | 1.5V-4.5V | 1.5V-4.5V | 1.5V-4.5V | 1.5V-4.5V |
| Overcharge protection | 4.2V | 4.2V | 4.2V | 4.2V | 4.2V | 4.2V | 4.2V | 4.2V | 4.2V | 4.2V | 4.2V |
| Overdischarge protection | 2.5V | 2.5V | 2.5V | 2.5V | 2.5V | 2.5V | 2.5V | 2.5V | 2.5V | 2.5V | 2.5V |
| Overcurrent protection | 100A | 100A | 100A | 100A | 100A | 150A | 150A | 150A | 200A | 200A | 200A |
| Short circuit protection | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
| Temperature protection | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
| Bluetooth | IOS/Android | IOS/Android | IOS/Android | IOS/Android | IOS/Android | IOS/Android | IOS/Android | IOS/Android | IOS/Android | IOS/Android | IOS/Android |
Note: This table provides a summary of parameters for BD4A/BD6A series. For full details on all models, refer to the comprehensive parameter table in the official documentation.

Image: Comprehensive parameter table for JIKONG Smart BMS models.
8. User Tips
- Always double-check wiring connections before powering on the BMS to prevent damage.
- Ensure your battery pack voltage meets the minimum requirement (20V for default BMS, 10V for 4S BMS) for initial startup.
- Regularly monitor cell balance and overall battery health through the mobile app.
- If using the heating function, ensure the external heating film/charger is correctly connected and compatible.
- For optimal performance, keep the BMS firmware updated.
9. Warranty and Support
JIKONG BMS products are designed for reliability and performance. For any issues or support needs, please refer to the following:
- Return & Refund Policy: Refer to the seller's return and refund policy for details on product returns and refunds.
- Fast Delivery & Refunds for Issues: The seller offers guarantees such as a coupon code if delivery is delayed, and refunds if the package is lost or items are damaged.
- Security & Privacy: Your personal details are protected and not shared with third parties without consent.
For further assistance, please contact the Smart JIKONG BMS Factory Store directly.

Image: JIKONG Smart BMS units, showcasing their versatility across different battery types and current ratings.

Image: JIKONG BMS product certifications (RoHS, FCC, CE).