1. Introduction
This document provides essential information for the safe and efficient operation of your PowMr Hybrid Solar Inverter. This multi-function inverter/charger seamlessly combines the capabilities of an inverter, solar charger, and battery charger to provide uninterruptible power support. It features a comprehensive LCD display for user-configurable settings such as battery charging current, AC/solar charger priority, and acceptable input voltage ranges.
Key Features:
- Pure Sine Wave Output
- Configurable input voltage range for home appliances and personal computers
- Configurable battery charging current based on applications
- Configurable AC/Solar Charger priority
- Compatible with mains voltage or generator power
- Auto restart while AC is recovering
- Overload, Over temperature, and Short circuit protection
- Smart battery charger design for optimized battery performance
- Cold start function
- Wide MPPT Voltage Range: 60~500VDC
- Maximum PV Input Power: 6500W
- Maximum Charging Current: 120A
- Supports both Lithium-ion and Lead-acid battery systems
- Lithium battery activation function
- Dual AC Outputs (Main and Second load)
- Can operate without a battery (depending on model and configuration)
2. Setup
2.1 Unpacking and Inspection
Upon receiving your PowMr Hybrid Solar Inverter, carefully unpack the unit and inspect it for any damage. The package typically includes the inverter unit and a user manual. If any components are missing or damaged, contact your supplier immediately.
2.2 Physical Installation
The inverter should be installed in a well-ventilated area, away from direct sunlight, heat sources, and moisture. Ensure sufficient clearance around the unit for proper airflow. The unit is designed for wall mounting.


2.3 Electrical Connections
All electrical connections must be performed by a qualified electrician in accordance with local and national electrical codes. Ensure all power sources are disconnected before making any connections.

- Solar Panel Connection (PV IN): Connect your solar array to the PV IN terminals. Ensure the PV array MPPT voltage range (60-500V DC for 4.2KW 24V, 90-500V DC for 6.2KW 48V) and maximum PV array power (6200W for 4.2KW, 6500W for 6.2KW) are respected. Observe correct polarity.
- Battery Connection (BATTERY): Connect the battery bank to the BATTERY terminals. The inverter supports 24V or 48V battery systems depending on the model. Ensure correct polarity (+ to + and - to -). The inverter is compatible with Lifepo4, Lithium, Flooded, Gel, and Lead-acid batteries. For lithium batteries, the system includes a lithium activation function.
- AC Input Connection (AC IN): Connect the utility grid or a generator to the AC IN terminals.
- AC Output Connection (MAIN OUT, SECOND OUT): Connect your loads (home appliances) to the MAIN OUT and SECOND OUT terminals. The inverter provides dual AC outputs.
- Communication Port (COMM): The inverter includes a COMM port for potential monitoring or control connections, such as a network cable for WIFI module (if equipped).

3. Operating Instructions
3.1 Powering On/Off
Once all connections are secure, you can power on the inverter. Follow the specific power-up sequence outlined in the full manual (if available) to avoid damage. To power off, reverse the sequence.
3.2 LCD Display and Settings
The inverter features an LCD display and buttons for configuring various operational parameters. These settings allow you to customize the inverter's behavior according to your specific needs, such as battery charging current, AC/solar charger priority, and input voltage range.
3.3 Charging and Output Modes
The inverter supports multiple charging and output modes, allowing for flexible power management:

- Solar Priority: Solar energy is primarily used to power loads and charge batteries.
- Solar + Utility: Solar energy is prioritized, with the utility grid providing supplemental power when solar is insufficient.
- Only Solar: The system relies solely on solar power.
- Utility Priority: The utility grid is the primary power source, with solar energy used as a backup or to charge batteries.
- SBU Mode: Solar-Battery-Utility mode, where solar powers the load, then battery, then utility.
3.4 Video Overview
4. Maintenance
Regular maintenance ensures the longevity and optimal performance of your inverter.
- Cleaning: Keep the inverter clean and free from dust. The unit features a demountable insect screen for easy cleaning, which helps maintain proper ventilation and prevents overheating.
- Ventilation: Ensure that the ventilation openings are not blocked. Proper airflow is crucial for dissipating heat.
- Connection Checks: Periodically check all electrical connections to ensure they are tight and free from corrosion.
- Environmental Conditions: Ensure the inverter is operating within its specified environmental conditions (temperature, humidity).
5. Troubleshooting
The PowMr Hybrid Solar Inverter is equipped with multiple protection features to ensure safe and stable operation. If you encounter an issue, refer to the following information.

Common Issues and Protections:
- Overload Protection: The inverter will protect itself if the connected load exceeds its rated capacity (e.g., 3s at ≥150% load; 5s at 101%~150% load). Reduce the load to resume normal operation.
- Over Temperature Protection: If the internal temperature of the inverter becomes too high, it will shut down to prevent damage. Ensure adequate ventilation and clean any blocked vents.
- Short Circuit Protection: The inverter will automatically shut down in case of a short circuit at the output. Identify and resolve the short circuit before restarting.
- Over/Under Voltage Protection: The inverter monitors input and output voltages and will protect against conditions outside the safe operating range.
- Over Current Protection: Protects against excessive current draw.
- Backfill Protection: Prevents reverse current flow.
- Over Charge Protection: Ensures batteries are not overcharged.
User Tips:
- Battery-less Operation: Certain models of this inverter can operate without a battery, directly converting solar power to AC for loads. Verify your specific model's capabilities.
- Lithium Battery Activation: When using lithium batteries, ensure the battery type is set to 'LI' in the inverter's settings. The inverter will activate the lithium battery using solar energy after approximately 3 seconds.
- Remote Monitoring: If your inverter model includes a WIFI module, you can connect it to your network via the COMM port for remote monitoring and control.
6. Specifications
| INVERTER MODEL | 4.2KW 24V | 6.2KW 48V |
|---|---|---|
| Input Voltage Waveform | Pure Sine Wave (Utility or Generator) | |
| Nominal Input Voltage | 230Vac | |
| Max AC Input Voltage | 300Vac | |
| Efficiency (Line Mode) | >95% (Rated R load, battery full charged) | |
| Transfer Time | 10ms typical (UPS); 20ms typical (Appliances) | |
| INVERTER MODEL | 4.2KW 24V | 6.2KW 48V |
|---|---|---|
| Rated Output Power | 4.2KW | 6.2KW |
| Output Voltage Waveform | Pure Sine Wave | |
| Output Voltage Regulation | 230Vac±5% | |
| Output Frequency | 50HZ/60HZ | |
| Peak Efficiency | 93% | |
| Overload Protection | 3s@≥150% load; 5s@101%~150% load | |
| Surge Capacity | 2* rated power for 5 seconds | |
| Nominal DC Input Voltage | 24Vdc | 48Vdc |
| Cold Start Voltage | 23.0Vdc | 46.0Vdc |
| No Load Power Consumption | 30W | 50W |
| INVERTER MODEL | 4.2KW 24V | 6.2KW 48V |
|---|---|---|
| Utility Charging Mode | ||
| Charging Algorithm | 3-Step | |
| AC Charging Current (Max) | 100A | 100A |
| MPPT Solar Charging Mode | ||
| Max. PV Array Power | 6200W | 6500W |
| Nominal PV Voltage | 240Vdc | 360Vdc |
| PV Array MPPT Voltage Range | 60Vdc~450Vdc | 90Vdc~500Vdc |
| Max. PV Array Open Circuit Voltage | 500Vdc | |
| Max Charging Current (AC charger plus solar charger) | 120A | 120A |
| INVERTER MODEL | 4.2KW 24V | 6.2KW 48V |
|---|---|---|
| Nominal Output Voltage | 220/230/240VAC | |
| Feed-in Grid Voltage Range | 195-253VAC | |
| Feed-in Grid Frequency Range | 49-51±1Hz/59-61±1Hz | |
| Nominal Output Current | 18.2A | 26.9A |
| Maximum Conversion Efficiency (DC/AC) | 97% | |
| INVERTER MODEL | 4.2M 24V | 6.2KW 48V |
|---|---|---|
| Full Load | 4200W | 6200W |
| Maximum Main Load | 4200W | 6200W |
| Maximum Second Load (battery model) | 1400W | 2066W |
| Main Load Cut Off Voltage | 26VDC | 52VDC |
| Main Load Return Voltage | 27VDC | 54VDC |
General Specifications:
- Size: 437x390x130 mm
- Weight: 10KG
- Output Type: SINGLE
- Output Frequency: 50HZ/60HZ
- Is Smart Device: Yes
- Certification: CE
- Applicable Area: Asia, Europe, Africa and North America (220-240VAC drivers)
7. Warranty and Support
The PowMr Hybrid Solar Inverter comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal operating conditions.
For technical support, troubleshooting assistance, or warranty claims, please contact your original point of purchase or the PowMr customer service department. Ensure you have your product model number and purchase details available when seeking support.