INKBIRD ITC-1000

Contents

INKBIRD ITC-1000 Digital Temperature Controller User Manual

Model: ITC-1000

Brand: INKBIRD

1. Safety Precautions

Thank you for choosing INKBIRD products. Please read this instruction manual carefully before use to ensure correct application and maintenance.

  • Ensure the product is used within its specified parameters.
  • Do not touch when electrified. Failure to do so may cause personal injury due to electric shock.
  • Do not allow metal fragments, wire clippings, or fine metal shavings or filings to enter the product during installation. This may lead to electric shock, fire, or malfunction.
  • Do not use this product in environments with flammable and explosive gases. This may result in explosive damage.
  • Do not touch any internal parts while disassembling, modifying, or repairing the product. This may cause failure, electric shock, or fire.

If the output relays are used past their life expectancy, contact fusing or burning may occasionally occur. Always consider the application conditions and use the output relays within their rated load and electrical life expectancy. The life expectancy of output relays varies considerably with the output load and switch conditions.

2. Main Functions

The INKBIRD ITC-1000 Digital Temperature Controller offers the following key functionalities:

  • Fahrenheit and Celsius display options.
  • User-friendly operation.
  • Ability to switch between cooling and heating modes.
  • Temperature control by setting a target temperature value and a difference value.
  • Temperature calibration feature.
  • Refrigerating control output delay protection.
  • Alarm activation when temperature exceeds set limits or in case of sensor error.

3. Specifications

3.1. General Specifications

ParameterValue
Temperature Measuring Range-50~99°C / -50~210°F
Temperature Resolution0.1°C / 0.1°F
Measuring Accuracy±1°C (-50~70°C) / ±1°F (-50~160°F)
Power Supply110Vac/220Vac 50Hz/60Hz, 12Vdc
Power Consumption<3W
Sensor TypeNTC Sensor (Included)
Sensor Length2m (including the probe)
Relay Contact CapacityCooling (10A/250VAC) / Heating (10A/250VAC)
Ambient Temperature0°C~60°C
Storage Temperature-30°C~75°C
Relative Humidity20-85% (No Condensate)

3.2. Dimensions

  • Front Panel Size: 75(L)*34.5(W)mm
  • Mounting Size: 71(L)*29(W)mm
  • Product Size: 75(L)*34.5(W)*85(D)mm
Diagram showing the front panel, mounting, and product dimensions of the ITC-1000 temperature controller.
Figure 1: Product Dimensions

4. Panel Instruction

Front panel of the ITC-1000 with labeled buttons and indicators.
Figure 2: Control Panel Layout
  • Power Key (A): Power On and Off, Confirm the Setting Value, Save and Exit Function.
  • Up Key (B): Choose Parameter, Increase Value and Check the Setting Temperature Value.
  • Down Key (C): Choose Parameter, Decrease Value and Check the Setting Difference Value.
  • Set Key (D): Entry, Exit and Set Parameters.
  • Setting Indicator Lamp (E): On: Setting Status.
  • PV/SV Display (F): Displays Process Value, Set Value and Parameter Menu.
  • Cool Indicator Lamp (G): On: Refrigerating Start; Off: Refrigerating Stop; Flash: Compressor Delay.
  • Heat Indicator Lamp (H): On: Heating Start; Off: Heating Stop.

5. Key Operating Instruction

5.1. Check Parameter

In normal working status:

  • Press the "Up" key once to display the setting temperature value.
  • Press the "Down" key once to display the difference value.

5.2. Parameter Setting

To enter the parameter setting mode:

  1. In normal working status, keep pressing the "S" key for more than 3 seconds. The set indicator lamp will turn on, and the screen will display the first menu code "TS".
  2. Press the "Up" or "Down" key to navigate through the menu items and display the menu codes.
  3. Press the "S" key to enter the parameter setting of the current menu. The parameter value will start to flash.
  4. Press the "Up" or "Down" key to adjust the parameter value of the current menu.
  5. After setting, press the "S" key to exit the parameter setting of the current menu. The parameter value will stop flashing. You can set other functions by following the steps above.
  6. In any status, press the "Power" key to save the modified parameter value and return to the normal temperature display. If no operation is performed within 10 seconds, the menu will automatically exit and return to normal temperature display status, without saving the modification.

6. Operating Instruction

  • Turning On/Off: In normal working status, press and hold the "Power" key for more than 3 seconds to turn off the controller. In power-off status, press and hold the "Power" key for more than 1 second to turn on the controller.
  • Automatic Mode Switching: In normal working status, the screen displays the current measured value. The controller automatically switches between heating and cooling modes.
  • Refrigerating Operation: If the measured temperature is greater than or equal to (temperature set value + difference set value), the controller starts refrigerating. The cool indicator lamp lights up, and the refrigerating relay is connected. When the cool indicator lamp flashes, it indicates that the refrigerating device is under compressor delay protection status.
  • Refrigerating Stop: If the measured temperature is less than or equal to the temperature set value, the cool indicator lamp turns off, and the refrigerating relay is disconnected.
  • Heating Operation: If the measured temperature is less than or equal to (temperature set value - difference set value), the controller starts heating. The heat indicator lamp lights up, and the heating relay is connected.
  • Heating Stop: If the measured temperature is greater than or equal to the temperature set value, the heat indicator lamp turns off, and the heating relay is disconnected.

7. Menu Instruction

7.1. When the set temperature is in Celsius (°C)

CodeFunctionSet RangeDefaultNote
TSTemperature Set Value-50~99.9°C10.0°C
DSDifference Set Value0.3~15°C1.0°C
PTCompressor Delay0~10 minutes3 minutes
CATemperature Calibration Value-15°C~15°C0°C
CFFahrenheit or Celsius SettingC

7.2. When the set temperature is in Fahrenheit (°F)

CodeFunctionSet RangeDefaultNote
TSTemperature Set Value-50~210°F50°FMin. Unit 1°F
DSDifference Set Value1~30°F3°F
PTCompressor Delay0~10 minutes3 minutes
CATemperature Calibration Value-15~15°F0°F
CFFahrenheit or Celsius SettingF

Note:

When the CF value changes, all set values will restore to their default values.

8. Wiring Diagram

Detailed wiring diagram for the ITC-1000 temperature controller, showing connections for power, sensor, heating, and cooling.
Figure 3: Wiring Diagram

Wiring Notes:

  1. Connect the positive ('+') power to terminal #1. Use another wire to connect terminal #1 to #5 and #7.
  2. Connect the negative ('-') of the power to terminal #2. Connect the positive ('+') of the cooling device to #6, and the positive ('+') of the heating device to #8.
  3. Connect the temperature probe to terminals #3 and #4.

9. Error Description

9.1. Sensor Error Alarm

When the temperature sensor circuit is short-circuited or open-circuited, the controller enters sensor error mode and closes all running statuses. The buzzer alarm sounds, and the screen displays "ER". Pressing any key will cancel the buzzer alarm, and the system will return to normal working status after the error is cleared.

9.2. Over-temperature Alarm

When the measured temperature exceeds the temperature measuring range, the controller enters over-temperature error alarm mode and closes all running statuses. The buzzer alarm sounds, and the screen displays "HL". Pressing any key will cancel the buzzer alarm, and the system will return to normal working status after the temperature returns to the measuring range.

10. Troubleshooting Guide

IssueCausesSolutions
The probe reading is incorrect.
  • The probe is placed in an area with poor temperature circulation.
  • The probe is damaged.
  1. Adjust the position of the probe.
  2. If the probe was used in liquids, dry it using a hairdryer and then test it at room temperature.
  3. Check if the probe is intact.
  4. If the deviation is small, use the CA function to calibrate.
Cannot enter setting mode.
  • The program is not responding.
  • There is a problem with the button.
  1. Unplug the controller.
  2. Press and hold the 'SET' button.
  3. Plug the controller back in and release the 'SET' button when power is applied.
  4. The unit will enter test mode. Press the 'up' and 'down' buttons alternately. Unplug the controller again and plug it back in without pressing the 'SET' button. The device should now enter normal mode.
  5. If it still does not work, please contact customer service.

11. User Tips

  • Ensure heating and cooling devices are properly wired to the power supply to complete the circuit.
  • If the cooling device doesn't start immediately and the cool indicator lamp flashes, consider setting the Compressor Delay (PT) to 0 if immediate operation is desired.
  • This controller is noted by users for its stability and effectiveness across various applications.

12. Warranty and Support

The INKBIRD ITC-1000 Digital Temperature Controller comes with a 12-month warranty.

For further assistance, product usage videos, or to download the detailed user manual in PDF format, please visit the official INKBIRD website at www.inkbird.com or contact support via email at support@inkbird.com.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.