CENTURY AOKE RYO-XPX-5P / J027

Contents

DC 5-30V 433Mhz RF Wireless Remote Control Switch Instruction Manual

Model: RYO-XPX-5P (Receiver) / J027 (Transmitter)

1. Product Overview

This RF Wireless Remote Control Switch system consists of a receiver module (RYO-XPX-5P) and a remote control transmitter (J027). It is designed for controlling various DC 5-30V applications such as LED lighting, access door systems, water pumps, and other equipment requiring remote on/off functionality. The system operates on a 433MHz frequency and offers multiple working modes for versatile control.

Image of the RYO-XPX-5P receiver module and J027 remote control
Figure 1: RYO-XPX-5P Receiver Module and J027 Remote Control

2. Specifications

2.1 Receiver Module (RYO-XPX-5P)

  • Model Number: RYO-XPX-5P
  • RF Working Mode: Superheterodyne Reception
  • Modulation Mode: ASK
  • Input Voltage: DC 5 ~ 30V
  • RF Frequency: 433MHz
  • Quiescent Current: 5mA
  • Receiving Sensitivity: >97dbm
  • Theoretical Remote Control Distance: >80-100m (actual distance may vary based on environment)
  • Wired Connection Way: Fixed Wiring Pillar
  • Decoding Mode: MCU Software Decoding
  • Max Current: 10A
  • Max Load: 240W
  • Output Voltage: Contact output / 1-250V
  • Pins: NO / COM / NC
  • Circuit Board Weight: 20g
  • Circuit Board Size: 3.5 x 3.0 x 1.8 cm (1.37 x 1.18 x 0.7 in)
Close-up of the RYO-XPX-5P receiver module circuit board
Figure 2: RYO-XPX-5P Receiver Module

2.2 Transmitter (J027)

  • Model Number: J027
  • Operating Frequency: 433MHz
  • Power: 3V Coin Cell Button Battery (CR2032 included)
  • Material: PVC
  • Buttons: 2 Buttons (ON/OFF)
  • Size: 59mm x 28mm x 8mm
  • Operating Voltage: 3V
  • Operating Current: 12mA
  • Transmitting Power: 10mw
  • Modulation Mode: ASK (AM)
  • Encoding Type: Learning Code
  • Transfer Distance: 20-50 m
Image showing dimensions and battery type for the J027 remote control
Figure 3: J027 Remote Control Dimensions and Battery

3. Setup and Wiring

Before connecting, ensure the power supply is disconnected to prevent electric shock or damage to the module. The receiver module has fixed wiring pillars for connection.

3.1 Receiver Wiring Terminals

Back of the receiver board showing GND, IN-V+, NO, COM, NC terminals
Figure 4: Receiver Module Wiring Terminals
  • GND: Ground connection for power input.
  • IN-V+: Positive power input (DC 5-30V).
  • NO (Normally Open): Output terminal.
  • COM (Common): Common output terminal.
  • NC (Normally Closed): Output terminal.

3.2 Basic Wiring for Device Control

The output switching signal can replace a physical switch to control other devices. Connect the power supply to IN-V+ and GND. Connect your device to the NO/COM or NC/COM terminals depending on your desired default state (Normally Open or Normally Closed).

Wiring diagram for controlling a device with DC 5-30V input
Figure 5: Wiring for Door Open Button or Other Devices

3.3 Advanced Wiring Examples

The module can control both DC and AC loads (up to 250V, 10A). Ensure proper insulation and safety precautions when working with AC voltage.

Wiring diagrams for controlling a light with DC input, a light with 1-250V input, and an electromagnetic lock
Figure 6: Wiring Examples for Lights and Electromagnetic Lock

4. Operating Instructions

The receiver module supports various working modes. You must program the remote control to the desired mode.

4.1 Working Modes Explained

  • Momentary Mode: Press and hold the remote button, the relay connects. Release the remote button, the relay disconnects.
  • Toggle Mode: Press the remote button once, the relay connects. Press the same remote button again, the relay disconnects.
  • Latching Mode: This mode requires two buttons on the remote. Press button A, the relay connects. Press button B, the relay disconnects.
  • Time Delay Mode: Press the remote control button, the relay connects. Upon releasing the remote button, a timer starts, and the relay automatically disconnects after a set delay (5s, 10s, or 15s).

4.2 Clearing the Code

To clear all previously learned remote controls from the receiver:

  1. Press the Learning Button on the receiver module 8 times consecutively.
  2. The codes will be cleared. After this, all previously paired remote controls will no longer work with this receiver.

4.3 Learning the Code (Pairing Remote)

Follow these steps to pair your remote control in the desired working mode:

4.3.1 Momentary Mode

  1. Press the Learning Button on the receiver once.
  2. Wait for a moment; the LED indicator on the receiver will turn off, indicating it's in learning state.
  3. Press the desired button on your remote control. The LED indicator on the receiver board will flash and then turn off.
  4. After approximately 3 seconds, the LED indicator will turn on again, confirming successful learning.

4.3.2 Toggle Mode

  1. Press the Learning Button on the receiver twice.
  2. Wait for a moment; the LED indicator on the receiver will turn off, indicating it's in learning state.
  3. Press the desired button on your remote control. The LED indicator on the receiver board will flash and then turn off.
  4. After approximately 3 seconds, the LED indicator will turn on again, confirming successful learning.

4.3.3 Latching Mode

For Latching Mode, you need to assign two different buttons on your remote: one for ON and one for OFF.

  1. Press the Learning Button on the receiver three times.
  2. Wait for a moment; the LED indicator on the receiver board will flash and then turn off.
  3. Press the first remote button (e.g., 'ON'). The LED will flash 5 times.
  4. Press the second remote button (e.g., 'OFF'). The LED will flash 5 times.
  5. After approximately 3 seconds, the LED indicator will turn on again, confirming successful learning. (e.g., Button A = ON, Button B = OFF).

4.3.4 Time Delay Mode

Choose the desired delay time:

  • 5 Seconds Delay: Press the Learning Button on the receiver four times.
  • 10 Seconds Delay: Press the Learning Button on the receiver five times.
  • 15 Seconds Delay: Press the Learning Button on the receiver six times.

After selecting the delay:

  1. The LED indicator will turn off.
  2. Press the desired button on your remote control. The LED will flash and then turn off.
  3. After approximately 3 seconds, the LED indicator will turn on again, confirming successful learning.

4.4 Power-on Function Learning Method (Auto-ON)

This function allows the relay to automatically connect (turn on) when power is applied to the receiver module.

  1. Continuously press the Learning Button on the control panel 8 times. The LED indicator will blink once.
  2. The LED indicator will then light up.
  3. Press the remote control button that you wish to code for this function. The control panel LED indicator flashes 3 times, indicating successful coding.

Note 1: This function means the relay automatically absorbs (turns on) upon power-up, also known as the 'incoming call to turn on the light' function.

Note 2: If you have learned the 'power on' function and wish to change to another operating mode, you must first clear the code (Section 4.2) before learning a new mode.

5. Maintenance

5.1 Remote Control Battery Replacement

The J027 remote control is powered by a CR2032 coin cell battery. If the remote's range decreases or it stops responding, the battery may need replacement.

  1. Carefully open the remote control casing.
  2. Remove the old CR2032 battery.
  3. Insert a new CR2032 battery, ensuring correct polarity (+/-).
  4. Close the remote control casing securely.

5.2 General Care

  • Keep the receiver module and remote control dry and away from moisture.
  • Avoid exposing the devices to extreme temperatures.
  • Clean the devices with a soft, dry cloth. Do not use harsh chemicals or solvents.
  • Ensure the receiver module is installed in a location with good ventilation and away from strong electromagnetic interference.

6. Troubleshooting

  • Remote control not working after programming: Ensure you have followed the correct learning procedure for the desired mode. If you cleared the code (Section 4.2), all remotes need to be re-paired.
  • Reduced remote control range: Check the remote control battery (replace if necessary). Ensure there are no significant obstructions (walls, metal objects) between the remote and the receiver. Large electrical devices or other RF signals can cause interference.
  • Device not responding: Verify that the receiver module is receiving power (DC 5-30V) and that the wiring to your device is correct and secure. Check the load's power supply and functionality independently.
  • LED indicator on receiver not behaving as expected: Refer to the 'Learning the Code' sections for expected LED behavior during programming. If the LED is not lighting up, check the power supply to the receiver.

7. User Tips

  • Test Range: Before final installation, test the remote control's effective range in your specific environment to ensure it meets your needs.
  • Power Supply: Always ensure the receiver is connected to a stable DC 5-30V power source. Incorrect voltage can damage the module.
  • Wiring Safety: When connecting to higher voltage or current devices, ensure all connections are properly insulated and secured to prevent short circuits or electrical hazards.

8. Frequently Asked Questions (FAQ)

Q: How can I program a new remote?
A: Please refer to Section 4.3, 'Learning the Code (Pairing Remote)', for detailed instructions on how to program your remote control to the receiver in various operating modes.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase records for reference.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.