MiLESEEY X5/X6/S6

Contents

MILESEEY Laser Distance Meter User Manual

Models: X5, X6, S6

1. Introduction

Thank you for choosing the MILESEEY Laser Distance Meter. This device is designed for high-precision distance measurement, offering various functions such as continuous measurement, area calculation, volume calculation, Pythagorean theorem measurement, and angle measurement. For safe and optimal use, please read this manual carefully before operation.

Key Features:

  • High performance and cost-effectiveness
  • Fast 0.5-second measurement
  • Accuracy: ±2mm
  • Multiple measurement functions (Single, Continuous, Area, Volume, Pythagorean, Secondary Pythagorean)
  • 20 groups of data recall
  • Units switch (m/ft/in/ft+in)
  • Addition/Subtraction function
  • Built-in horizontal bubble level
  • Waterproof & Dustproof design
MILESEEY Laser Measure features: accuracy, speed, multiple functions, data recall, unit switch, add/subtract, horizontal bubble, waterproof & dustproof.

Figure 1: MILESEEY Laser Measure Key Features

2. Safety Instructions

To ensure safe operation of your laser distance meter, please observe the following:

  • This device emits a Class 2 laser (<1mW). Do not stare directly into the laser beam or direct it at other people.
  • Do not use the product in explosive or corrosive environments.
  • Avoid using the product near medical equipment.
  • Do not use accessories from other manufacturers without approval.
  • Keep the device out of reach of children.

3. Setup

3.1 Battery Installation

  1. Open the battery cover located at the rear of the device.
  2. Insert 2 AAA batteries, ensuring correct polarity (+/-).
  3. Close the battery cover securely.

The device is powered by batteries (not included).

4. Operating Instructions

4.1 Initial Operation

  1. Power On/Off: Long press the Power button (Power button icon) to turn the instrument on or off. The device will automatically shut down if there is no operation within 3 minutes.
  2. Measurement Key: Short press the MEAS button (red button) to activate the laser. Press it again to take a single measurement.
  3. Return/Clear Key: Press the Clear button (back arrow icon) to clear data or return to the previous screen.
  4. Sound Setting: Short press the Mute button (speaker icon) to turn the sound on or off.

4.2 Measurement Modes

The device supports various measurement modes. Short press the Function key (square icon with multiple lines) to cycle through the modes.

Laser distance meter display showing various measurement modes: single, max/min, continuous, area, volume, Pythagorean, secondary Pythagorean, horizontal bubble level.

Figure 2: Multiple Measurement Functions

  1. Single Distance Measurement:
    Activate the laser by pressing MEAS. Aim the laser at the target and press MEAS again. The result will be displayed on the screen, and the laser will turn off.
  2. Continuous Measurement (Max/Min):
    Long press the MEAS button to enter continuous measurement mode. The screen will display the continuous measurement icon, along with the minimum and maximum values detected. Press MEAS again to stop. This function automatically stops after 5 minutes.
  3. Area Measurement:
    Select the Area Measurement mode. The device will prompt you to measure the length and width. After two measurements, the area will be automatically calculated and displayed.
  4. Volume Measurement:
    Select the Volume Measurement mode. The device will prompt you to measure the length, width, and height. After three measurements, the volume will be automatically calculated and displayed.
  5. Pythagorean Theorem Measurement (Two-point method):
    Select this mode. Measure the hypotenuse and one leg (vertical or horizontal edge). The device will calculate the other leg.
  6. Pythagorean Theorem Measurement (Three-point method):
    Select this mode. Measure two hypotenuses and one leg (vertical or horizontal edge). The device will calculate the remaining side.
  7. Auto Horizontal Measurement (Advanced models only):
    This function is available in specific versions.
  8. Auto Vertical Measurement (Advanced models only):
    This function is available in specific versions.

4.3 Unit Switching

Long press the Unit button (UNIT icon) to cycle through measurement units: meters (m), feet (ft), inches (in), and feet+inches (ft+in). The last selected unit is saved even after power off.

4.4 Measurement Reference

Short press the Reference button (icon with two arrows pointing to front/rear) to switch the measurement reference point between the front edge and the rear edge of the device. The last selected reference is saved.

4.5 Data Storage and Recall

The device can store up to 20 sets of measurement or calculation results. Short press the Storage key (icon with multiple lines and an arrow) to scroll through the stored records. Use the '+' and '-' buttons to navigate forward and backward through the records.

Laser distance meter display showing 20 sets of data storage.

Figure 3: 20 Sets Data Storage

4.6 Addition/Subtraction

After a measurement, short press the '+' button for addition or long press the '-' button for subtraction. You can repeat these operations as needed for continuous calculations.

4.7 Product Demonstration Video

Video: A demonstration of the MILESEEY Laser Distance Meter's basic operations, including power on/off, measurement modes, unit switching, and data recall.

5. Specifications

AttributeValue
Brand NameMiLESEEY
Model NumberX5/X6/S6
Measurement Range0.2 - 120m (depending on model variant)
Measurement Accuracy±2mm
Power TypeBattery-Powered (2x AAA batteries)
Battery IncludedNo
Laser Hazard LevelClass 2 (<1mW)
CertificationCE, FCC
OriginMainland China
Dimensions (L x W x H)115 x 50 x 20mm
Weight95g
Laser Auto-off106 seconds
Operating Temperature0°C - 40°C
Storage Temperature-10°C - 60°C

6. Troubleshooting

If you encounter any issues with your device, refer to the following table for common problems and their solutions:

Error CodeCauseSolution
Low Battery IconLow battery powerReplace the batteries.
252Temperature too highMove the device to a cooler environment.
253Temperature too lowMove the device to a warmer environment.
261Measurement out of rangeEnsure measurements are taken within the specified range (0.2m to 120m).
Hardware FailurePersistent issue after multiple power cyclesContact your dealer for assistance.

7. User Tips

  • Outdoor Use: While the device can be used outdoors, performance may be affected by strong sunlight or highly reflective/absorbent surfaces. Under poor measurement conditions (e.g., excessive light), the measurement error may increase. For best results, use in good lighting conditions or with a reflective target.
  • Power Source: The device is powered by 2 AAA batteries. Ensure you have spare batteries on hand for uninterrupted use.
  • Accuracy: For optimal accuracy (±2mm), ensure the measurement surface is good, the ambient temperature is stable (room temperature), and there is sufficient indoor light.
  • Data Review: Utilize the 20-set data storage feature to review previous measurements, which can be helpful for complex projects.

8. Warranty and Support

This product complies with GB 7247.1 "Safety of Laser Products - Part 1: Equipment Classification, Requirements". Product specifications are subject to change without prior notice.

For warranty terms and support, please refer to the warranty card included with your product or contact MiLESEEY directly.

Contact Information:

  • Manufacturer: Shenzhen Mileseey Technology Co., Ltd.
  • Address: Zhongxin 6th Road 13, Huizhou, Guangdong Province, Innovation Smart Hub, Wisdom Zone, China
  • Phone: 0755-86329055 / 0752-3222711
  • Website: www.mileseey.com

A PDF version of the user manual is available for download: User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.