Baofeng F22/T22 Series Two Way Radio User Manual

Introduction

Thanks for choosing BAOFENG! The F22/T22 is an FM two-way radio transceiver suitable for use in the 446 private mobile radio service (PMR446). It is programmed with 16 PMR446 frequencies, features a maximum transmission power of 500 mW, a bandwidth of 12.5 kHz, and a maximum transmission time limit of 180 seconds. It has a fixed antenna and requires no registration or fees, though restrictions of use may apply in some Non-EU countries. For further information, please consult the 'Restrictions on the use' chart.

Combining the latest technology in radio communication along with a sturdy mechanical frame, the F22/T22 is an ideal and effective solution for professionals who need to stay in touch with their working team (e.g., in construction sites, buildings, shows, trade fairs, or hotels) or for leisure users who want to keep up with friends and family.

Safety Information

ATTENTION!

Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio, which contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.

• WARNING: The Emergency Alert feature should only be used in the event of an actual emergency.
• Do not attempt to open the unit. Non-expert handling of the unit may damage it and/or annul the warranty.
• When using a regulated power supply, ensure the voltage is 5V to avoid damages.
• High temperatures can shorten the life of electronic devices and warp or melt certain plastics. Do not store the radio in dusty or dirty areas.
• Keep the radio dry. Rainwater or damp conditions will corrode electronic circuits.
• If the radio emits a peculiar smell or smoke, immediately shut off its power and remove the charger or battery.
• Do not transmit without an antenna.

Package Contents

• 2 F22/T22 Transceivers
• 2 1400mAh Li-ion Rechargeable Battery Packs
• 2 Belt Clips
• 2 Desktop Chargers
• 2 Hand Straps
• 1 User Manual

Product Overview and Controls

Main Controls and Parts of the Radio

1. Antenna
2. LCD Display
3. UP button - Press to increase the volume. In Menu mode, used to change settings.
4. MENU/Lock button - Press to enter the radio's MENU. Keep pressed for about 3 seconds to activate the keypad lock.
5. Power/CALL button - To send a call to the selected channel. Keep pressed to turn on/off the radio.
6. DOWN button - Press to reduce the volume. In Menu mode, used to change settings.
7. Speaker and Built-in microphone
8. LED Flashlight
9. Belt Clip
10. MONI button: Keep pressed to activate the Monitor function (for weak signal monitoring).
11. SPK | MIC (under the protective cover) - To connect external audio devices such as microphones, headphones, etc.
12. SCAN button - Press this button once to activate SCAN.
13. USB port for the recharge of the radio
14. PTT button (Push-To-Talk)
15. LAMP/Emergency button - When the radio is switched on, press shortly to turn on/off the LED flashlight. Keep pressed to turn on/off the emergency alerts.

LCD Display

1. Scan Indicator
2. Activate the VOX function
3. Dual Channel Monitor
4. Select the DCS/CTCSS type of squelch method
5. Channel (1-16)
6. Battery Indicator
7. Emergency alert function activated
8. Transmit Status (TX)
9. Receive Status (RX)
10. Keypad Lock
11. Transmit power indicator. Low power only in PMR mode.
12. Displays the set CTCSS tone or DCS code (CTCSS: 1-50; DCS: 1-105)

Setup

Battery Installation and Charging

Li-Ion Battery Pack 'LB-T22'

Installation

• 1. Remove the belt clip (see 'Installing and Removing Belt Clips').
• 2. Open the battery compartment.
• 3. Insert the Li-Ion battery pack into the appropriate compartment.
• 4. Close the battery compartment with the cover and reattach the belt clip.

Charging

Place your transceiver in the desktop charger cradle or connect the wall adapter to the correct socket on the radio. Recharge of the Li-Ion battery is managed by a radio processor and the battery status can be checked by the icon on the screen and by seeing it on the desktop charger:

• Charging status is indicated by the LED on the desktop charger and by the flashing battery icon on the radio display.
• When charging is complete, the LED will be off and the battery icon on the screen will be full of bars.

NiMH Batteries (3 x AA, Optional)

Installation

The radio can also be powered by 3 AA non-rechargeable alkaline batteries (Not Included).

• 1. Remove the belt clip.
• 2. Open the battery compartment.
• 3. Insert 3 AA batteries, observing polarity.
• 4. Close the battery compartment with the cover and reattach the belt clip.

Charging (for rechargeable NiMH)

Place your transceiver in the desktop charger cradle or connect the wall adapter to the correct socket on the radio. A full charge takes about 5 hours. We suggest you detach the wall adapter from the radio or remove the radio from the desktop charger cradle after 5 hours.

The battery icon on the radio display will flash during the entire charging process, as well as the red LED will be on on the desktop charger.

Note: Alkaline batteries can only be used for replacement and cannot be recharged. NiMH batteries can be recharged and recycled.

Belt Clip Installation

• To remove the belt clip, slide it upwards from the slot on the unit.
• To install the belt clip, slide it into the guides on the back of the transceiver until it clicks into place.

Basic Operations

Power On/Off and Volume Adjustment

To turn the radio on, keep the CALL button pressed. To adjust the volume level, press the UP or DOWN button. If the radio does not pick up any signal, momentarily activate the Monitor function to detect weak signals, then adjust the volume. To turn the radio off, keep the CALL button pressed until a switch-off tone is heard.

Keypad Lock

To avoid accidentally changing radio settings, press the MENU button for 3 seconds. The lock icon will appear on the display. The PTT, CALL, and MONI keys will still be active. Repeat the same procedure to unlock the keypad.

Flashlight Function

You can use this radio in an emergency. If you press the LAMP/Emergency button, the radio turns on the high-intensity LED flashlight:

• Press the button once: continuous light (Always On mode).
• Press the button again: Strobe Light emits the emergency signal (Strobe emergency mode).
• Press the button a third time: light turns off.

Talking on Your Radio (PTT)

1) Press and hold the PTT button and speak in a clear, normal voice about 2-3 inches away from the microphone. While transmitting, the TX icon appears on the display. To avoid cutting off the first part of your transmission, pause slightly after pressing the PTT button before speaking.

2) When you have finished speaking, release the PTT button. You can now receive incoming calls. While receiving, the RX icon displays.

Monitor Mode Feature

Your radio allows you to listen for weak signals on the current channel. To turn on Monitor mode: Press the MONI button. The receiver circuit stays open, and both noise and weak signals can be heard. The RX icon blinks. To turn off Monitor mode: Press the MONI button again to return to normal mode, and the RX icon stops blinking and disappears.

Channel Scanning

The F22/T22 can automatically search for signals throughout the PMR bands by scanning channels in rapid sequence. When a signal is detected, scanning pauses on that channel, and you can transmit by pushing PTT. If you press PTT during scanning, you transmit on the channel from which scanning started. The UP or DOWN buttons allow you to change the scanning direction (from lower to higher channels or vice versa) and skip communications of no interest.

Press the SCAN button briefly to start scanning. To stop, press SCAN again. Your transceiver will return to the channel from which scanning originally started.

Scanning Sub-Codes (CTCSS/DCS)

Press and hold the SCAN button to enter Sub-Codes scanning. A flashing "CTC/DCS" will appear in the left status display. The lower display will cycle through Sub-Codes as they are tested. Once the received Privacy code is determined, the "CTC/DCS" indicator will stop flashing. Press the PTT button to save the scanned tone into memory. During scanning, press and hold SCAN to exit Sub-Code scanning.

Setting CTCSS/DCS Tones

1) To select CTCSS/DCS, press MENU twice until the display shows CTC or DCS (flashing on the lower left).

2) By pushing the UP or DOWN button, the display will show CTCSS (ct blinking) or DCS (dc blinking); press MENU to enter the CTCSS or DCS tones. Now select the desired tone with the UP or DOWN buttons.

3) Press the PTT button to exit menu or MENU button to continue setup.

VOX Function (Hands-Free Operation)

BAOFENG F22/T22 enables hands-free conversations through VOX function.

1) To activate VOX function, press the MENU button 4 times, and 'VOX' will appear on the display.

2) Use the UP or DOWN buttons to select the desired setting:

• 1 = high sensitivity (normal voice with no background noise)
• 2 = Medium Sensitivity for most environments
• 3 = low sensitivity (useful in very noisy areas or if you talk loudly)

3) Press the PTT button to exit menu or MENU button to continue setup. To disable VOX, select 'oF' (OFF: Disabled) in the settings.

Call Tones

BAOFENG F22/T22 can transmit different call tones to other radios in your group to alert them. Your radio has 10 call tones:

1) Press the MENU button 5 times, and 'CA' will appear on the display.

2) Press UP or DOWN to change and listen to the call tone.

3) Press the PTT button to exit menu or MENU button to continue setup. To disable Call Tones, select 'oF' (OFF: Disabled) in the settings. To transmit your call tone, set the same channel and Sub-Code on your radio and press the CALL button.

Emergency Alert

The Emergency Alert feature signals group members for help. It is activated by menu operation.

1) To activate, press the MENU button 6 times until the display shows the 'alarm icon'.

2) Use the UP or DOWN buttons to select the desired setting:

• OF: Disabled
• 1. Local alarm: the radio itself emits an alarm sound.
• 2. Send an alarm tone on the current channel to signal group members.

3) Press the PTT button to exit menu or MENU button to continue setup.

WARNING: This feature should only be used in a true emergency. Baofeng assumes no responsibility if the receiving group does not respond.

Keypad Beep

To deactivate the keypad beep:

1) Press the MENU button 7 times until 'bp on' is displayed.

2) Use the UP or DOWN buttons until the display shows 'bp of'.

3) Press the PTT button to exit menu or MENU button to continue setup. The keypad will no longer beep.

Roger Beep Tone (End Transmission Tone)

When your transmission is finished (PTT released), the BAOFENG F22/T22 emits a sound indicating to the other party that they can start talking. This function is enabled by default.

To deactivate it:

1) Press the MENU button 8 times until the display shows 'rb on'.

2) Using the UP or DOWN buttons, select 'off' and 'rb of' will be displayed.

3) Press the PTT button to exit menu or MENU button to continue setup.

Dual Watch Mode

Your radio has a DUAL WATCH function to scan 2 channels for activity. The first channel will be the current channel setting, and the second will be the selected channel.

To set another channel and start Dual Watch:

1) Press the MENU button 9 times until the display shows 'of du'.

2) Using the UP or DOWN buttons, select the channel, then press MENU.

3) Using the UP or DOWN buttons, select the CTCSS/DCS, then press MENU.

4) The radio starts Dual Watch. The screen will alternate between the home channel and the Dual Channel Monitor channel.

Note: Dual Watch does not work if you set the same channel and Sub-code as the current channel.

5) Press the SCAN button to turn Dual Watch mode OFF.

Troubleshooting

• Q: I want to order a headset. Do you have? A: The radio features a 2pin Kenwood headset jack, allowing connection of compatible headsets. Please check with the seller for available accessories.
• Q: I ordered a set of walkie talkies, but after charging the batteries once, they don't work anymore. Do you have a solution? A: Ensure you are using the correct battery type (Li-Ion rechargeable or 3xAA non-rechargeable). If using rechargeable NiMH batteries, ensure they are suitable for recharging. If the issue persists, contact support.
• Q: If I need 5 at the same time, will they work on the same channel? A: Yes, all radios must be set to the same channel and privacy code (CTCSS/DCS) to communicate with each other.
• Q: Is there a program for setting frequencies in the set? A: The manual mentions a 'programming port' and 'sub-code scan and store' which implies some level of programmability, but specific software is not detailed. Consult the seller or manufacturer for programming tools.

Specifications

Maintenance

Your F22/T22 was designed for long-lasting performance. To ensure its longevity, please follow these suggestions:

• Do not attempt to open the unit. Improper handling may damage it and void the warranty.
• When using a regulated power supply, ensure the output voltage is 5V to prevent damage.
• Avoid high temperatures, which can shorten the life of electronic devices and deform plastics. Do not store the radio in dusty or dirty areas.
• Keep the radio dry. Rainwater or humidity can corrode electronic circuits.
• If the radio emits strange odors or smoke, immediately turn off the power and remove the charger or battery.
• Never transmit without an antenna.

User Tips

• For optimal range, especially in open areas, ensure the antenna is vertical and minimize obstructions like trees or buildings.
• Remember that PMR 446MHz is for European countries, while FRS 462MHz is for USA, Canada, Mexico, Brazil, etc. Choose the correct version for your region.
• When using AAA batteries, note that only NiMH batteries are rechargeable; alkaline batteries are for single use only.
• Utilize the NOAA Weather Alert feature for outdoor activities to stay informed about severe weather conditions.

Compliance and Support

EU Declaration of Conformity

Baofeng and Pofung declare that the radio equipment type listed in Technical Specifications complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at: http://www.pofung.cn/download.asp?EnBigClassName=EU%20DOC.

This product is an FM two-way radio transceiver suitable for use in the 446 private mobile radio service (PMR446). This is a license-exempt service, but restrictions of use may apply in some Non-EU countries.

Contact and Support

For further information or support, contact your local Baofeng helpdesk, your dealer, or send an email to wangjianhui@baofengradio.com.

EU Contact: APEX CE SPECIALISTS LIMITED, Unit 3D North Point House, North Point Business Park, New Mallow Road, Cork, T23 AT2P, Ireland.

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong. Website: Http://www.baofengradio.com