1. Introduction
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your ANDELI MCT-416 Multi-Process Welder and Plasma Cutter. Please read and understand this instruction manual carefully before installation and operation.
The ANDELI MCT-416 is an inverter MIG welder power supply with invariable voltage output external characteristics, manufactured with advanced IGBT inverter technology. It converts rectified input 50Hz/60Hz AC voltage to high-frequency 20KHz AC voltage, which is then transformed and rectified. This machine offers a 5-in-1 functionality, including Plasma Cutting, MIG, TIG, and MMA welding processes.
Key Features:
- IGBT inverter technology for high quality and stable performance.
- Closed feedback circuit and invariable voltage output, ensuring great balance voltage up to ±15%.
- Electron reactor control for stable welding, minimal splash, deep molten pool, and excellent welding bead shaping.
- Welding voltage can be preset, with the voltmeter displaying the preset value when not welding.
- Simultaneous display of welding current and voltage.
- Slow wire feeding during arc starting and melting ball removal after welding for reliable arc starting.
- Separated wire feeding part for a wide welding operation range.
- Small-sized, light-weighed, easy to operate, economical, and practical.
Operating Environment: Adequate ventilation is required for proper cooling. Ensure the machine is placed on a stable, level surface with clean, cool air circulation. Avoid excessive dust and dirt to protect electrical components and control circuit boards.
Product demonstration video showcasing the multi-process capabilities.
2. Safety Guidelines and Cautions
Welding and cutting operations are inherently dangerous. Strict adherence to safety regulations is crucial to protect the operator, nearby personnel, and the surrounding environment. Always read and understand this manual thoroughly before installation and operation.
General Safety Precautions:
- Electric Shock: It could be fatal!
- Always connect the earth cable according to standard regulations.
- Avoid contact with live electrical parts of the welding circuit, electrodes, and wires with bare hands.
- Wear dry welding gloves during welding tasks.
- A safety switch is necessary to prevent electric leakage.
- Smoke and Gas: Harmful to people's health.
- Avoid breathing smoke and gas generated during welding or cutting.
- Ensure the working area is well ventilated.
- Arc Rays: Harmful to people's eyes and skin.
- Wear a welding helmet, anti-radiation glasses, and appropriate work clothes during welding operations.
- Take measures to protect people in or near the working area from arc rays.
- Fire Hazard:
- Welding sparks can cause fires. Remove all flammable materials from the working area.
- Keep a fire extinguisher nearby and ensure a trained person is ready to use it.
- Noise: Possibly harmful to hearing.
- Wear approved ear protection if the noise level is high during welding/cutting.
- Machine Fault:
- Consult this instruction manual for troubleshooting.
- Contact your local dealer or supplier for further advice if issues persist.
Specific Cautions:
- Do not switch function modes while welding is in progress, as this may damage the machine.
- Always disconnect the electrode-holder cable from the machine before performing welding.
- The welding splash may cause fire, thus remove flammable material away from the working place.
- Since the arc of MIG welding is much stronger than that of MMA welding, always wear a welding helmet and protective clothing.
- Operation of CUT welding requires a compressed air supply and consumables. These accessories are not included standard with the machine; contact your supplier for details.
- Gas shielded MIG welding requires a shielding gas supply, gas regulator, and gas shielded MIG wire. These accessories are not supplied standard with the MIG machine; contact your local dealers for details.
- TIG operation requires an argon gas supply, TIG torch, consumables, and a gas regulator. These accessories are not included standard with the MIG machine; contact your supplier for further details.


3. Specifications and Main Parameters
The ANDELI MCT-416 is a versatile welding and cutting machine with the following technical specifications:
| Parameter | 110V±10% | 220V±10% |
|---|---|---|
| Model Number | MCT-416 | |
| Power Supply Voltage (V) | 110/220V | |
| Rated Input Capacity (KW) | 4.0 (MIG), 3.2 (TIG), 4.0 (MMA), 4.0 (CUT) | 6.2 (MIG), 4.6 (TIG), 7.5 (MMA), 6.8 (CUT) |
| Rated Input Current (A) | 37 (MIG), 29 (TIG), 37 (MMA), 36 (CUT) | 28 (MIG), 21 (TIG), 34 (MMA), 31 (CUT) |
| Output Current Range (A) | 50-120 (MIG), 10-120 (TIG), 10-100 (MMA), 20-25 (CUT) | 50-160 (MIG), 10-160 (TIG), 10-160 (MMA), 20-40 (CUT) |
| Duty Cycle (40℃ 10min) | 20%120A (MIG), 30%120A (TIG), 20%100A (MMA), 20%25A (CUT) | 20%160A (MIG), 20%160A (TIG), 20%160A (MMA), 20%40A (CUT) |
| No Load Voltage (V) | 53 | |
| Efficiency % | 77% | |
| Power Factor | 0.73 | |
| IP | 21S | |
| Insulation Class | H | |
| Cooling Way | FAN & AIR | |
| Dimensions (L*W*H) (mm) | 490*225*340 | |
| Weight (Kg) | 21.0 (Package Weight) | |
| Certification | CE | |
| Frequency | 50/60Hz | |
Note: The duty cycle is the percentage of actual continuous welding time in a ten-minute cycle. For example, 20% at 200 amps means the welder can operate continuously at 200 amps for 2 minutes, followed by an 8-minute rest. Duty cycles can be affected by ambient temperature; higher temperatures (exceeding 40°C) may reduce the duty cycle, while lower temperatures may increase it. All tests are conducted at 40°C.

Detailed product parameters for the MCT-416 model.
4. Product Overview and Structure
The ANDELI MCT-416 is a 5-in-1 multi-function welder. Below are the details of its LED control panel and physical structure.
4.1 Full LED Panel Display Structure & Operation

LED display and control panel for welding parameters.
The control panel features a large digital screen for easy adjustment of welding parameters and automatic matching of current, voltage, and wire feeder speed.
- Button 1: Select Wire diameter (0.8/0.9/1.0)
- Button 2: Select 2T/4T/SPOT Function
- Button 3: Select gas type (CO2/MIX Gas/Flux cored (Gasless))
- Button 4: Select welding mode (MIG/MANUAL/LIFT TIG/CUT/MMA)
- Button 5: Gas check function
- Button 6: Wire check function
- Button 7: Select Inductance (-10 to +10%), VRD (for MMA only) function, Pre-flow time (0-1S), Post-Flow time (0.1-10S)
- Knob 8: Adjust Fine Voltage/Welding Current & Voltage/Wire feed speed/Inductance
4.2 Front & Back Panel Structure


Front Panel Components:
- Europe Type torch connector
- Negative (-) Welding Output Terminal
- Polar conversion line
- Aviation socket for Cutting torch switch
- Positive (+) Welding Output Terminal
- CUT Negative (-) Welding Output Terminal
Rear Panel Components:
- Power cable
- Power Switch
- MIG welding gas inlet
- CUT welding gas inlet
- Reducing Valve
5. Installation and Setup
Proper installation is critical for the safe and effective operation of your welding machine. Follow these instructions carefully.
5.1 MIG Welding Setup & Operation
5.1.1 Fitting the Wire Spool & Wire Feeder Tension Adjustment

Diagram showing wire spool and tensioner arm.
- Open the door of the welder and remove the Spool Retaining Knob from the Wire Spool Spindle.
- Slide the Wire Spool onto the center of the Spindle. Ensure the Drive Pin of the Spindle engages with a spoke of the wire spool.
- Reinstall the Spool Retaining Knob.
- To set the spool tension, incrementally tighten the Spool Retaining Knob until there is a slight resistance to spinning the wire spool on the spindle.
- If the tension is too loose, the wire spool will freely spin and unspool.
- If the tension is too tight, the Drive Roller will have difficulty pulling the wire off the spool, leading to slipping.
Warning! Before changing the feed roller or wire spool, ensure the mains power is switched off.
Warning! The use of excessive feed tension will cause rapid and premature wear of the drive roller, the support bearing, and the drive motor.
5.1.2 Setup for Gasless MIG Welding Operation
- Connect the MIG Torch Euro Connector to the torch socket on the front of the welder. Secure by firmly hand tightening the threaded collar on the MIG Torch Euro Connector clockwise.
- Check that the correct flux cored, gasless wire, matching drive roller, and welding tip are fitted.
- Connect Torch Connection Power Lead to the negative (-) welding output terminal.
- Connect Earth Lead Quick Connector to the positive (+) welding output terminal.
5.1.3 Setup for Gas Shielded MIG Welding Operation
- Connect the MIG Torch Euro Connector to the torch socket on the front of the welder. Secure by firmly hand tightening the threaded collar on the MIG Torch Euro Connector clockwise.
- Check that the correct gas shielded wire, matching drive roller, and welding tip are fitted.
- Connect Polar conversion line to the positive (+) welding output terminal.
- Connect Earth Lead Quick Connector to the negative (-) output welding terminal.
- Connect Earth Clamp to the work piece. Ensure strong contact with clean, bare metal, free from corrosion, paint, or scale.
- Connect the gas regulator (optional) and gas line to the inlet on the rear panel. If the regulator has a flow gauge, set the flow between 8–15 L/minute. If not, adjust pressure until gas can just be heard coming out of the torch conical nozzle. Check gas flow again just prior to welding.
Warning! Gas shielded MIG welding requires a shielding gas supply, gas regulator, and gas shielded MIG wire. These accessories are not supplied standard with the MIG machine. Please contact your local dealers for details.
5.1.4 Setup for MMA/STICK Mode Operation
- Connect Electrode holder Quick Connector to the positive (+) welding output terminal.
- Connect Earth Lead Quick Connector to the negative (-) output welding terminal.
Warning! MMA/Stick Welding requires an MMA lead set.
5.1.5 Setup for Lift TIG Welding Operation
- Connect Lift TIG torch Quick Connector to the negative (-) output welding terminal.
- Connect Earth Lead Quick Connector to the positive (+) welding output terminal.
- Connect the air hose of Lift TIG torch with the Argon meter connector.
Warning! TIG operation requires an argon gas supply, TIG torch, consumables, and gas regulator. These accessories are not included standard with the MIG machine; contact your supplier for further details.
5.1.6 Setup for CUT Welding Operation
- Connect CUT torch Quick Connector to the welding terminal as shown in the picture.
- Connect Earth Lead Quick Connector to the positive (+) output terminal.
- Connect the air hose of Cut torch with the Air meter connector.
- Connect the Cut torch with the Air Interface.
- Adjust the Air Compressor pressure to 0.3-0.45MPa.
| Cutting Current (A) | Max Cutting Thickness (Carbon steel) |
|---|---|
| 20 | 6mm |
| 30 | 10mm |
| 35 | 14mm |
| 40 | 18mm |
Warning! Operation requires a Compressed air supply and consumables. These accessories are not included standard with the machine; contact your supplier for further details.
Connection of Shield Gas (for MIG)
Connect the CO2 hose from the wire feeder to the copper nozzle of the gas bottle. The gas supply system includes the gas bottle, air regulator, and gas hose. The heater cable should be inserted into the socket on the machine's back, and the hose clamp used to tighten it to prevent leakage or air-in, ensuring the welding spot is protected.
Please note:
- Leakage of shielding gas affects arc welding performance.
- Avoid direct sunlight on the gas cylinder to prevent explosion due to heat-induced pressure increase.
- It is strictly forbidden to knock at the gas cylinder or lay it horizontally.
- Ensure no person is near the regulator before releasing or shutting off gas output.
- For machines with heating power output, insert the power supply plug of the heater into the 36 VAC (5A) socket on the back panel. For machines without heating power output, use an AC220V heater.
- The gas output volume meter should be installed vertically for precise measurement.
- Before installing the gas regulator, release and shut off the gas several times to clear the line.
6. Welding Settings and Parameters
Optimal welding current and voltage settings are crucial for welding stability, quality, and productivity. The following tables provide quick reference and detailed parameters.
6.1 Welding Settings Quick Reference Chart
| Welding Material | Wire Type | Polarity | Wire Size | Shielding Gas | Material Thickness (mm) - Setting Key: Voltage/Wire Speed | |||||
|---|---|---|---|---|---|---|---|---|---|---|
| 1.0 | 2.0 | 3.0 | 4.0 | 5.0 | 6.0 | |||||
| Mild Steel | Self Shielded Flux Core | Torch Negative(-) | 0.8mm | N/A | 14.0/2.7 | 16.2/3.0 | 18.5/6.1 | 24.5/9.0 | ||
| Mild Steel | Self Shielded Flux Core | Torch Negative(-) | 0.9mm | N/A | 16.3/2.0 | 18.8/3.6 | 20.2/4.1 | 21.0/7.5 | 21.6/9.0 | |
| Mild Steel | Solid Wire ER70S-6 | Torch Positive(+) | 0.6mm | 75%Argon+25%CO2 | 15.9/3.4 | 19.5/7.8 | ||||
| Mild Steel | Solid Wire ER70S-6 | Torch Positive(+) | 0.8mm | 75%Argon+25%CO2 | 12.8/2.0 | 14.1/3.3 | 17.5/6.6 | 20.0/8.2 | 21.0/9.0 | 21.0/9.0 |
| Mild Steel | Solid Wire ER70S-6 | Torch Positive(+) | 0.6mm | 100%CO2 | 14.2/2.1 | 19.8/8.1 | ||||
| Mild Steel | Solid Wire ER70S-6 | Torch Positive(+) | 0.8mm | 100%CO2 | 13.6/2.3 | 14.4/3.6 | 18.4/4.2 | 21.1/8.5 | 22.6/9.0 | |
Use this chart as a guide only, as optimal settings will vary with joint type and operator technique. Cells left blank are not a recommended configuration.
6.2 Basic Welding Guide (MIG/GMAW/FCAW)
MIG (Gas Metal Arc Welding - GMAW) and Flux Cored Arc Welding (FCAW) are covered. These processes involve a welding gun, an electrode (welding wire) fed into a weld puddle, and an arc shielded by gas or flux.
GMAW Process:
Also known as MIG welding, CO2 welding, Micro Wire Welding, short arc welding, or dip transfer welding. This electric arc welding process fuses parts by heating them with an arc between a continuous, consumable electrode and the work-piece. Shielding is provided by an externally supplied welding grade shielding gas or gas mixture. It is commonly applied semi-automatically for various steels and some non-ferrous metals.

Diagram illustrating the GMAW welding process with shielding gas, electrode, and molten metal.
FCAW Process:
This process fuses parts by heating them with an arc between a continuous flux-filled electrode wire and the work-piece. Shielding is obtained through the decomposition of the flux within the tubular wire. Additional shielding may be obtained from an externally supplied gas or gas mixture. It is commonly used for large diameter electrodes in flat and horizontal positions, and small electrode diameters in all positions.
6.3 Position of MIG Torch
The angle of the MIG torch to the weld affects the width of the weld.

Illustrations of different MIG torch angles: Push, Vertical, and Drag/Pull.
The welding gun should be held at an angle to the weld joint. Hold the gun so the welding seam is visible at all times. Always wear a welding helmet with proper filter lenses and use appropriate safety equipment.
Travel Speed:
The speed at which the molten pool travels influences the width of the weld and penetration of the welding run.
MIG Welding (GMAW) Variables:
These variables control the welding process, penetration, bead width, bead height, arc stability, deposition rate, and weld soundness.
- Pre-selected Variables: Depend on material type, thickness, welding position, deposition rate, and mechanical properties. These include the type of electrode wire, type of gas (if applicable), and gas flow rate (if applicable).
- Primary Adjustable Variables: Arc Voltage, Welding current (wire feed speed), Travel speed.
- Secondary Adjustable Variables: Stick-out (distance between contact tube and electrode wire end, maintain ~10mm), Wire Feed Speed (increases weld current, decreases arc length).
- Nozzle Angle: Transverse angle (half the included angle between plates) and longitudinal angle (between gun center line and perpendicular to weld axis).
6.4 Range of Welding Current and Voltage in CO2 Welding
The choice of welding speed, wire stretching out length, and CO2 flow volume significantly impact welding quality and productivity.
Option of Welding Speed:
Welding speed affects protection efficiency and cooling. Too fast a speed weakens protection and cooling, while too slow a speed can damage the work-piece. Welding speed should not exceed 1m/min.
Length of Wire Stretching Out:
The length of wire stretching out of the nozzle should be appropriate. Increasing it can improve productivity, but too long a stretch causes excessive spatter. Generally, it should be 10 times the welding wire diameter.
Setting of CO2 Flow Volume:
Protection efficiency is the primary consideration. Inner-angle welding has better protection efficiency than external-angle welding. Refer to the following figure for main parameters.
| Wire Diameter | Short Circuit Transition | Granular Transition | ||
|---|---|---|---|---|
| (mm) | Current (A) | Voltage (V) | Current (A) | Voltage (V) |
| 0.6 | 40~70 | 17~19 | 160~400 | 25~38 |
| 0.8 | 60~100 | 18~19 | 200~500 | 26~40 |
| 1.0 | 80~120 | 18~21 | 200~600 | 27~40 |
| Welding Mode | Thin Wire CO2 Welding (L/min) | Thick Wire CO2 Welding (L/min) | Thick Wire, Big Current CO2 Welding (L/min) |
|---|---|---|---|
| CO2 Flow Volume | 5~15 | 15~25 | 25~50 |
6.5 Welding Parameters Table
The following tables provide reference parameters for butt-welding and flat fillet welding. Optimal settings depend on welding diameter, melting form, and production requirements.
Parameter for Butt-Welding:
| Plate Thickness t (mm) | Gap g (mm) | Wire (mm) | Welding Current (A) | Welding Voltage (V) | Welding Speed (cm/min) | Gas Volume (L/min) |
|---|---|---|---|---|---|---|
| 0.8 | 0 | 0.8~0.9 | 60~70 | 16~16.5 | 50~60 | 10 |
| 1.0 | 0 | 0.8~0.9 | 75~85 | 17~17.5 | 50~60 | 10~15 |
| 1.2 | 0 | 1.0 | 70~80 | 17~18 | 45~55 | 10 |
| 1.6 | 0 | 1.0 | 80~100 | 18~19 | 45~55 | 10~15 |
| 2.0 | 0~0.5 | 1.0 | 100~110 | 19~20 | 40~55 | 10~15 |
| 2.3 | 0.5~1.0 | 1.0 or 1.2 | 110~130 | 19~20 | 50~55 | 10~15 |
| 3.2 | 1.0~1.2 | 1.0 or 1.2 | 130~150 | 19~21 | 40~50 | 10~15 |
| 4.5 | 1.2~1.5 | 1.2 | 150~170 | 21~23 | 40~50 | 10~15 |
Parameter for Flat Fillet Welding:
| Plate Thickness t (mm) | Corn Size I (mm) | Wire (mm) | Welding Current (A) | Welding Voltage (V) | Welding Speed (cm/min) | Gas Volume (L/min) |
|---|---|---|---|---|---|---|
| 1.0 | 2.5~3.0 | 0.8~0.9 | 70~80 | 17~18 | 50~60 | 10~15 |
| 1.2 | 2.5~3.0 | 1.0 | 70~100 | 18~19 | 50~60 | 10~15 |
| 1.6 | 2.5~3.0 | 1.0~1.2 | 90~120 | 18~20 | 50~60 | 10~15 |
| 2.0 | 3.0~3.5 | 1.0~1.2 | 100~130 | 19~20 | 50~60 | 10~20 |
| 2.3 | 2.5~3.0 | 1.0~1.2 | 120~140 | 19~21 | 50~60 | 10~20 |
| 3.2 | 3.0~4.0 | 1.0~1.2 | 130~170 | 19~21 | 45~55 | 10~20 |
| 4.5 | 4.0~4.5 | 1.2 | 190~230 | 22~24 | 45~55 | 10~20 |
Parameter for Fillet Welding in Vertical Position:
| Plate Thickness t (mm) | Welding Position | Wire (mm) | Welding Current (A) | Welding Voltage (V) | Welding Speed (cm/min) | Gas Volume (L/min) |
|---|---|---|---|---|---|---|
| 0.8 | A | 0.8~0.9 | 60~70 | 16~17 | 40~45 | 10~15 |
| 1.2 | A | 1.0 | 80~100 | 18~19 | 45~55 | 10~15 |
| 1.6 | A | 1.0~1.2 | 100~120 | 18~20 | 45~55 | 10~15 |
| 2.0 | A or B | 1.0~1.2 | 100~130 | 18~20 | 45~55 | 15~20 |
| 2.3 | B | 1.0~1.2 | 120~140 | 19~21 | 45~50 | 15~20 |
| 3.2 | B | 1.0~1.2 | 130~160 | 19~22 | 45~50 | 15~20 |
| 4.5 | B | 1.2 | 150~200 | 21~24 | 40~45 | 15~20 |
Parameter for Lap Welding:
| Plate Thickness t (mm) | Corn Size I (mm) | Wire (mm) | Welding Current (A) | Welding Voltage (V) | Welding Speed (cm/min) | Gas Volume (L/min) |
|---|---|---|---|---|---|---|
| 1.2 | 2.5~3.0 | 1.0 | 70~100 | 18~19 | 50~60 | 10~15 |
| 1.6 | 2.5~3.0 | 1.0~1.2 | 90~120 | 18~20 | 50~60 | 10~15 |
| 2.0 | 3.0~3.5 | 1.0~1.2 | 100~130 | 19~20 | 50~60 | 10~20 |
| 2.3 | 3.0~3.5 | 1.0~1.2 | 120~140 | 19~21 | 50~60 | 10~20 |
| 3.2 | 3.0~4.0 | 1.0~1.2 | 130~170 | 22~22 | 45~55 | 10~20 |
| 4.5 | 4.0~4.5 | 1.2 | 200~250 | 23~26 | 45~55 | 10~20 |
7. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welding machine.
- Disconnect the input plug or power before any maintenance or repair.
- Ensure the input ground wire is properly connected to a ground terminal.
- Check inner gas-electricity connections (especially plugs) for tightness. If loose, tighten. If oxidized, remove oxidation with sandpaper and re-connect.
- Keep hands, hair, loose clothing, and tools away from electrical parts like fans and wires when the machine is switched on.
- Clear dust at regular intervals with clean, dry compressed air. In heavy smoke or air pollution environments, clean daily.
- Reduce compressed air pressure to the required level to prevent damage to small internal parts.
- If exposed to water or rain, dry the machine immediately. Check insulation with a megohmmeter (between connections and between case and connections). Continue welding only if no abnormal phenomena are detected.
- If the machine is not used for a long time, store it in its original packing in a dry condition.
8. Daily Checking
Daily checking is vital for making the best use of the machine. Inspect the torch, wire-feeding vehicle, PCBs, gas hole, etc. Remove dust or replace parts as needed. Only qualified technicians are authorized to repair and check this equipment in case of machine fault.
8.1 Power Supply Check
| Part | Check | Remarks |
|---|---|---|
| Control panel | 1. Operation, replacement and installation of Switch. 2. Switch on the power, and check if the power indicator is on. | |
| Fan | 1. Check if the fan is functioning and the sound generated is normal. | If the fan doesn't work or the sound is abnormal, do inner check. |
| Power supply | 1. Switch on the power supply, and check if abnormal vibration, heating of the case of this equipment, variation of colors of case or buzz presents. | |
| Other parts | 1. Check if gas connection is available, case and other joints are in good connection. |
8.2 Welding Torch Check
| Part | Check | Remarks |
|---|---|---|
| Nozzle | 1. Check if the nozzle is fixed firmly and distortion of the tip exists. 2. Check if there is spatter sticking on the nozzle. | Possible gas leakage occurs due to the unfixed nozzle. Spatter possibly leads to the damage of torch. Use anti-spatter to eliminate the spatter. |
| Contact tip | 1. Check if the contact tip is fixed firmly. 2. Check if the contact tip is physically complete. | Ufixed contact tip possibly leads to unstable arc. The physically incomplete contact tip possibly leads to unstable arc and arc automatically terminating. |
| Wire feeding hose | 1. Make sure that there is the agreement of wire and wire feed tube. 2. Make sure that there is no bending or elongation of wire feed tube. 3. Make sure that there is no dust or spatter accumulated inside the wire. | Disagreement of the diameters of wire and wire feed tube possibly leads to the unstable arc. Replace it/them if necessary. Bending and elongation of wire feed tube possibly leads to the unstable wire feed and arc. Replace it if necessary. If there is dust or spatter, remove it. |
8.3 Wire Feeder Check
| Part | Check | Remarks |
|---|---|---|
| Pressure adjusting handle | 1. Check if the pressure-adjusting handle is fixed and adjusted to the desired position. | The unfixed pressure-adjusting handle leads to the unstable welding output. |
| Wire-feeding hose | 1. Check if there is dust or spatter inside the hose or beside wire-feeding wheel. 2. Check if there is a diameter agreement of wire and wire-feeding hose. 3. Check if rod and wire feeding groove are concentric. | Remove the dust. Non-agreement of the diameter of wire and wire-feeding hose possibly leads to the excessive spatter and unstable arc. Unstable arc possibly occurs. |
| Wire-feeding wheel | 1. Check if there is an agreement of wire diameter and wire-feeding wheel. 2. Check if the wire groove is blocked. | Non-agreement of wire diameter and wire-feeding wheel possibly leads to the excessive spatter and unstable arc. Replace it if necessary. |
| Pressure adjusting wheel | 1. Check if the pressure adjusting wheel can rotate smoothly, and it's physically complete. | Unstable rotation or physically incompleteness of the wheel possibly leads to unstable wire feeding and arc. |
8.4 Cables Check
| Part | Check | Remarks |
|---|---|---|
| Torch cable | 1. Check if the cable of torch is twisted. 2. Check if the coupling plug is in loose connection. | The twisted torch cable leads to unstable wire feeding and arc. |
| Output cable | 1. Check if the cable is physically complete. 2. Check if insulation damage or loose connection exists. | Relevant measures should be taken to obtain stable weld and prevent the possible electric shock. |
| Input cable | 1. Check if the cable is physically complete. 2. Check if insulation damage or loose connection exists. | |
| Earth cable | 1. Check if the earth cables are well fixed and not short-circuited. 2. Check if this welding equipment is well grounded. | Relevant measures should be taken to prevent the possible electric shock. |
9. Connection Diagram of the Machine
Below is the internal connection diagram of the ANDELI MCT-416 welding machine.

Detailed internal circuit connection diagram.
10. Explosion Drawing and Parts List
This section provides an exploded view of the ANDELI MCT-416 and a corresponding list of its components.

Exploded view of the ANDELI MCT-416 showing internal and external components.
| NO. | Part Name | Consumable | NO. | Part Name | Consumables |
|---|---|---|---|---|---|
| 1 | Main PCB Board | YES | 13 | Clapboard | |
| 2 | Dual Voltage transfer board | YES | 14 | Base Plate | |
| 3 | IGBT | YES | 15 | Wire Feeder Fixed Plate | |
| 4 | Fast recovery Diode | YES | 16 | Wire Feeder Motor | |
| 5 | Fast recovery Diode plastic protector | YES | 17 | Wire Feeder Shaft | |
| 6 | HF Board | YES | 18 | Fan | YES |
| 7 | Switch Board | 19 | Rear Metal Panel | ||
| 8 | Control Panel PCB Board | YES | 20 | Rear plastic panel(down) | |
| 9 | Plastic Front& Rear Panel (Up) | 21 | Reducing valve Fixed Plate | ||
| 10 | Front Plastic Panel(down) | 22 | Side plate | ||
| 11 | Front Metal Panel | 23 | Handle | ||
| 12 | Metal Protection Cover | 24 | Machine Cover |
11. User Tips
- Plasma Cutting Air Supply: For plasma cutting, ensure you have a dedicated compressed air supply. The machine requires compressed air, not a special gas, for cutting operations.
- Welding Aluminum: While the machine is capable of welding non-ferrous metals, specific settings and appropriate filler wire (e.g., aluminum MIG wire) are crucial for successful aluminum welding. Consult welding guides for optimal parameters for aluminum.
- Wire Feed Tension: Properly adjust the wire feed tension to avoid issues. Too loose, and the wire will unspool; too tight, and it will cause premature wear and slipping.
- Ventilation: Always ensure ample ventilation in your workspace to dissipate welding fumes and prevent overheating of the machine.
12. Frequently Asked Questions (FAQ)
- Q: Does the plasma cutting function use compressor air or a special gas?
- A: The plasma cutting function requires a compressed air supply. No special gas is needed for cutting with this machine.
- Q: Can this machine weld aluminum?
- A: Yes, this multi-process welder is capable of welding non-ferrous metals, including aluminum, using the appropriate MIG or TIG settings and filler materials. Refer to the welding parameters and consult specific guides for aluminum welding.
13. Warranty and Support
This welding machine comes with a one-year guarantee from the date of purchase.
For any machine faults or technical assistance beyond the scope of this manual, please contact your local dealer or supplier for further advice and support.