CNSPEED 620 Series Car Performance Gauges

Contents

CNSPEED 60mm 2.5-inch Car Performance Gauges User Manual

Model: 620 Series

1. Product Overview

The CNSPEED 620 Series gauges are professional 2.5-inch (60mm) diameter instruments designed for 12V automotive applications. They provide accurate readings for various engine parameters, enhancing vehicle monitoring and performance tuning. Each gauge features two backlight options: white and amber.

CNSPEED 60mm Boost Gauge and other gauges
Figure 1: Assortment of CNSPEED 60mm gauges including Boost, Water Temp, Oil Pressure, Oil Temp, and Voltmeter.

Available Gauge Types:

  • Boost Gauge (PSI, bar)
  • Water Temperature Meter
  • Oil Temperature Gauge
  • Oil Pressure Gauge
  • Voltmeter
  • Air Fuel Ratio Indicator
  • Exhaust Gas Temperature Gauge
  • Tachometer (for 4/6/8 cylinder gasoline engines)
Overview of various gauge types and their included components
Figure 2: Detailed view of different gauge types and their respective accessories, including sensors, wiring, and mounting hardware.

2. Installation Guide

Professional installation is highly recommended for all CNSPEED 620 Series gauges. Ensure the vehicle's power is disconnected before beginning installation.

General Wiring Instructions:

  • Power: Connect to a DC 12V professional power source.
  • Backlight Control:
    • White Backlight Mode: Connect the positive Red and White wires in parallel.
    • Amber Backlight Mode: Connect the positive Red and Orange-Red wires in parallel.
  • Signal Wires: Connect the specific signal wire from the sensor to the corresponding input on the gauge.
  • Ground: Ensure a secure ground connection.
Side view of a gauge showing wiring connections
Figure 3: Side view of a CNSPEED gauge illustrating the rear wiring terminals for power, ground, and signal inputs.

Component Breakdown (Example: Water Temperature Gauge):

Water Temperature Gauge with components
Figure 4: Water Temperature Gauge kit showing the gauge, temperature sensor, signal wires (200cm), power cord (41cm), screws (x2), rubber ring, power series line (20.5cm), instrument cover ring, and instructions.

Each gauge type comes with specific sensors and wiring harnesses. Refer to the individual gauge's included instructions for precise sensor installation and wiring diagrams.

Gauge with mounting ring
Figure 5: Gauge with its mounting ring, which helps secure the gauge in place.

3. Operating Instructions

Power-On Self-Test:

Upon initial power-up, the gauge performs a self-test:

  • White Backlight Mode: The backlight flashes between white and amber. The needle light and the blue PEAK light illuminate. After the self-test, the backlight remains white, and the PEAK light turns off.
  • Amber Backlight Mode: The backlight flashes between orange and amber. The needle light and the blue PEAK light illuminate. After the self-test, the backlight remains orange, and the PEAK light turns off.

Buzzer Settings:

To toggle the buzzer (mute/unmute):

  1. Restart the power to the gauge.
  2. Before the tachometer finishes its self-test, press and hold the button.
  3. Release the button once the buzzer sound disappears (to mute) or reappears (to unmute).

Clearing the PEAK Value (Maximum Memory Value):

The PEAK value stores the highest recorded reading.

  1. After the self-test is complete, press and release the button. The blue PEAK light will turn on.
  2. Press and hold the button again for 3 seconds until the PEAK light flashes.
  3. Release the button to clear the PEAK value. The needle will return to zero after approximately 3 seconds.

Setting the Alarm Point and Cylinder Count:

These settings are typically for the Tachometer or gauges with alarm functions.

  • Alarm Point Setting:
    1. After the self-test, press and hold the button for 5 seconds until the needle illumination flashes. Release the button.
    2. Press the button again to set the alarm point. Use quick, repeated presses for fine adjustments or hold the button for rapid adjustment.
    3. The needle will automatically return to zero after 5 seconds, allowing for the next step.
  • Cylinder Setting (for Tachometer):
    1. After the self-test, or once the needle has returned to zero, press and hold the button for 10 seconds until the needle illumination flashes. Release the button.
    2. Press the button again to set the cylinder count (e.g., 4, 6, or 8 cylinders).
    3. Release the button. The needle will automatically return to zero after 5 seconds.
  • RPM Alarm Alert: When the RPM alarm is triggered, the lights will flash alternately between Red/White or Red/Orange-Red.
Video 1: Demonstration of CNSPEED gauges cycling through different backlight colors and performing their power-on self-test sequence.

4. Maintenance

To ensure the longevity and accuracy of your CNSPEED gauges, follow these simple maintenance guidelines:

  • Cleaning: Use a soft, dry cloth to clean the gauge face and body. Avoid abrasive cleaners or solvents that could damage the plastic or finish.
  • Connection Checks: Periodically inspect all wiring connections to ensure they are secure and free from corrosion. Loose connections can lead to inaccurate readings or intermittent operation.
  • Sensor Inspection: For gauges with external sensors (e.g., temperature, pressure), check the sensor and its wiring for any signs of damage or wear.

5. Troubleshooting

Gauge Not Lighting Up / Incorrect Backlight:

Wiring diagram for troubleshooting gauge lighting
Figure 6: Wiring diagram illustrating connections for different backlight colors. Red+ and Black- are power and ground. Orange and White wires control the amber and white light modes respectively. If the gauge doesn't light up, check Red+ and Black- connections. For specific light colors, ensure the correct Orange or White wire is connected to Red+.
  • No Light: Ensure the Red (+) and Black (-) wires are correctly connected to a 12V power source and ground, respectively.
  • Incorrect Light Color: Verify that the White wire (for white light) or Orange wire (for amber light) is correctly connected in parallel with the Red (+) wire as per the desired backlight mode.

Inaccurate Readings:

  • Check all sensor connections for tightness and proper installation.
  • Ensure the sensor itself is correctly installed in the appropriate location (e.g., water temp sensor in the coolant line, oil pressure sensor in the oil gallery).
  • Verify that the gauge is receiving stable 12V power.

Buzzer Malfunction:

  • If the buzzer is not working or constantly beeping, refer to the

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.