Tedeligo Tedeligo 433MHz 220V Garage Curtain Blinds Switch

Contents

RF 433MHz Garage Curtain Blinds Motor Remote Control Switch

Model: Tedeligo 433MHz 220V Garage Curtain Blinds Switch

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Tedeligo RF 433MHz Garage Curtain Blinds Motor Remote Control Switch. This device is designed to provide convenient two-way control (wireless and wired) for various AC motors used in applications such as garage doors, roller shutters, curtains, and gates.

For additional information, a PDF version of the user manual is available. Please refer to the seller's product page for the direct link to the PDF document.

Safety Information

  • Always disconnect power before performing any installation or maintenance.
  • Installation should be performed by a qualified electrician or technician.
  • Ensure all wiring connections are secure and correctly insulated to prevent short circuits and electrical hazards.
  • Do not expose the device to moisture or extreme temperatures outside its specified operating range (-30~+80 Celsius).
  • Verify that the supply voltage (AC 90-250V) matches the device's requirements.

Package Contents

Depending on your purchase, your package may include:

  • RF Motor Control Switch Receiver
  • RF Remote Control (with battery: 2*CR2016 or 1*CR2032)
  • RF Wall Switch (optional, with battery: 1pcs 27A12V)
  • RF 5-Channel Remote Control (optional, with battery: 1pcs 27A12V)
Tedeligo RF Motor Control Switch and Remote
Image: Tedeligo RF Motor Control Switch and a single remote control.

Specifications

Feature Specification
Brand Nametedeligo
Model NumberTedeligo 433MHz 220V Garage Curtain Blinds Switch
Voltage110-240V
Wattage20W
OriginMainland China
CertificationCE, RoHS
RF Standard433.92 MHz
Switch Working VoltageAC 90-250 V 50/60HZ
Switch Size70*50*25 mm
RF Remote Size55*30 mm
RF Remote Battery2*CR2016 or 1*CR2032 (Included)
RF Wall Switch Size86*86 mm
RF Wall Switch Battery1pcs 27A12V (Included)
RF 5 Channel Remote Size110*40 mm
RF 5 Channel Remote Battery1pcs 27A12V (Included)
Working Temperature-30~+80 Celsius
Quiescent CurrentLess than 5mA
ApplicationCurtain Motor, Gate, Blinds, Garage
Additional ApplicationsFamily, Farm, Factory, Office, Supermarket
EU LVD Voltage ComplianceLow voltage: Below 50Vac or 75Vdc
Battery IncludedYes

Setup and Wiring

Careful wiring is essential for the safe and correct operation of the control switch. Refer to the diagrams below for connection details.

Control Switch Components Overview

Control Switch Components and Dimensions
Image: Detailed view of the RF Motor Control Switch showing component labels and dimensions.
  1. Black Wire: Up limit switch connection.
  2. Red Wire: Down limit switch connection.
  3. Yellow Wire: Up switch connection (for external wired control).
  4. White Wire: Stop switch connection (for external wired control).
  5. Blue Wire: Down switch connection (for external wired control).
  6. Green Wire: Common pin for external wired control.
  7. Indicator Light: Provides status feedback.
  8. Learning Button: Used for pairing remote controls.
  9. Antenna: For RF signal reception.

Input Terminals: N (Neutral), L (Live) for AC 90-250V power supply.

Motor Terminals: Up, Down, M (Motor), N (Neutral) for connecting to the AC motor.

Wiring Diagram for AC Motor Control

Wiring Diagram for RF Motor Control Switch with AC Motor, External Button, and Limit Switches
Image: Comprehensive wiring diagram showing connections for AC motor, external wired control, and limit switches.
  • Power Input: Connect your AC 90-250V power supply (Live and Neutral) to the 'L' and 'N' input terminals on the control switch.
  • Motor Connection: Connect your AC motor's Up, Down, and Neutral wires to the corresponding 'Up', 'Down', and 'N' terminals under the 'MOTOR' section. The main motor wire connects to 'M'.
  • External Wired Control (Optional): If using an external button switch (e.g., a wall switch), connect its 'Up', 'Stop', 'Down' outputs to the Yellow, White, and Blue wires of the control switch, respectively. Connect the common wire of the external button to the Green wire.
  • Limit Switches (Optional): Connect the Up limit switch to the Black wire and the Down limit switch to the Red wire. These switches prevent the motor from over-extending.

The system supports both wireless control via the RF remote and wired control via an external button switch.

Pairing Remote Controls (Learning Function)

To pair a remote control with the receiver:

  1. Ensure the control switch is powered on.
  2. Press the 'Learning Button' (8) on the control switch. The indicator light (7) should illuminate or flash, indicating it's in learning mode.
  3. While the indicator light is active, press any button on the remote control you wish to pair (e.g., the 'Up' button).
  4. The indicator light on the control switch should flash or turn off, confirming successful pairing.
  5. Repeat for any additional remote controls.

Note: If you need to clear all paired remotes, press and hold the 'Learning Button' for approximately 8 seconds until the indicator light flashes rapidly and then turns off. This will reset all pairings.

Operating Instructions

Once installed and paired, operating the motor control switch is straightforward:

  • Remote Control: Use the dedicated 'Up', 'Down', and 'Stop' buttons on your RF remote control to operate the connected motor. The typical range for the remote is up to 50 meters.
  • Wired Control: If an external button switch is connected, you can use its 'Up', 'Down', and 'Stop' buttons for direct wired control.
RF433Mhz remote control with original button switch control
Image: Illustrates the use of the RF433Mhz remote control alongside an original wired button switch for comprehensive control.

Maintenance

  • Keep the control switch and remote controls clean and dry.
  • Avoid dropping the devices or subjecting them to strong impacts.
  • Replace remote control batteries when the range decreases or buttons become unresponsive. Refer to specifications for battery type (CR2032 for standard remote, 27A12V for wall switch/5-channel remote).
  • Periodically check wiring connections for any signs of wear or looseness.

Troubleshooting

Problem: Remote control not working or motor not responding.
Solution:
1. Check if the control switch has power. The indicator light should be on when powered.
2. Ensure the remote control battery is not depleted. Replace if necessary.
3. Re-pair the remote control with the receiver using the 'Learning Button' procedure described in the Setup section.
4. Verify all wiring connections to the motor and power supply are secure and correct.
5. Ensure the remote is within the effective operating range (approx. 50m).
Problem: Motor moves in the wrong direction (Up button makes it go Down).
Solution: Reverse the 'Up' and 'Down' motor wires connected to the control switch. Ensure power is disconnected before making any wiring changes.
Problem: Motor does not stop at desired positions.
Solution: Check the installation and wiring of the limit switches. Ensure they are correctly positioned and connected to the Black (Up Limit) and Red (Down Limit) wires.

User Tips

  • For optimal performance, ensure the receiver's antenna is not obstructed or coiled.
  • When installing, consider the placement of the receiver to minimize interference from large metal objects or other RF devices.
  • If using multiple remotes, pair them one by one and test each after pairing to confirm functionality.

Warranty and Support

This product comes with a standard manufacturer's warranty. Please retain your proof of purchase for any warranty claims. For technical support or further inquiries, please contact the seller or refer to the official Tedeligo website.

For detailed warranty terms and conditions, please refer to the documentation provided with your purchase or contact customer service.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.