PowMr L60A L80A

Contents

PowMr MPPT/PWM Solar Charge Controller User Manual

Models: L60A / L80A

Brand: PowMr

1. Introduction

This document provides comprehensive instructions for the installation, operation, and maintenance of your PowMr MPPT/PWM Solar Charge Controller, available in L60A and L80A models. This controller is designed for 12V and 24V solar systems, offering intelligent and efficient management of solar charging for various battery types, including lead-acid and lithium batteries.

The controller features a three-time control function for evening, pause, and dawn working times, allowing users to customize operation based on their specific needs. It combines the benefits of MPPT (Maximum Power Point Tracking) for 10-30% higher charging efficiency compared to ordinary controllers, with PWM (Pulse Width Modulation) technology. Additionally, it boasts significant energy-saving capabilities, consuming only 10mA-15mA in standby mode, which is over 30% less energy than conventional controllers.

Note: This is a high-quality compatible MPPT + PWM controller, not a 100% pure MPPT controller.

2. Specifications

The following table outlines the key technical specifications for the PowMr L60A and L80A solar charge controllers:

Table of technical specifications for PowMr L60 and L80 solar charge controllers
Figure 2.1: Technical Specifications Table

Detailed Specifications:

FeatureL-60 ModelL-80 Model
Maximum Power Current60A80A
Installation Line (mm²)16mm²20mm²
Installation Line (AWG)4#(AWG)2#(AWG)
Weight800g900g
Peak power of solar cell panel (Max Wp)800W1000W
Battery capacity configuration600AH800AH
Dimensions188*128*61(mm)
Battery float voltage13.8V (12V system) / 27.6V (24V system)
Battery (under voltage) protection10.6V (12V system) / 21.2V (24V system)
Battery (under voltage) recovery voltage12.6V (12V system) / 25.2V (24V system)
System load loss<=13mA
Loop Buck<=100mV
Operation Temperature-10°C ~ 60°C
Storage Temperature-30°C ~ 70°C
Operation Humidity<=90%, No condensation
Temperature compensation-4mV/Cell/°C
Maximum open circuit voltage of solar panel18V~24V (12V system) / 36V~48V (24V system)
Solar Panel maximum open circuit voltage<=48V

Additional Features:

  • Is Smart Device: Yes
  • Application: Thermal Controller, Charger Controller, Voltage Controller, Collector Controller, Lighting Controller, Solar System Controller
  • Certification: CE, RoHS
  • Origin: Mainland China

3. Components Overview

The PowMr Solar Charge Controller features a robust design with an intuitive LCD display and clearly marked terminals for easy connection.

Front view of the PowMr MPPT/PWM Solar Charge Controller (L80 model) showing the LCD display and control buttons.
Figure 3.1: Front View of Controller
Top view of the PowMr Solar Charge Controller, highlighting the USB 5V 1.0A port and the thermo scope input.
Figure 3.2: Top View with USB and Sensor Port
Bottom view of the PowMr Solar Charge Controller, showing the solar, battery, and load terminals.
Figure 3.3: Bottom View with Terminals
Side view of the PowMr Solar Charge Controller, illustrating the heat sink fins for cooling.
Figure 3.4: Side View with Heat Sink

3.1. LCD Display Overview

The LCD provides real-time information about your solar system. Refer to the diagrams below for a detailed breakdown of the display elements and their meanings.

A detailed diagram of the LCD display, labeling each segment with its corresponding function, including charging logo, battery voltage, load current, and system status indicators.
Figure 3.5: Detailed LCD Display Breakdown
A table explaining the symbols and values displayed on the LCD operating interface, such as charging status, ambient temperature, load current, and battery capacity.
Figure 3.6: LCD Symbols and Meanings

3.2. Function Keys

The controller features several buttons for setup and manual control:

An illustration of the function keys and their operations for setting parameters, toggling load, and resetting to factory settings.
Figure 3.7: Function Keys and Operations
  • Toggle key: Used to cycle through display modes or confirm settings.
  • '+' / '-' buttons: Used to adjust parameter values.
  • ON/OFF/RESET button: Manual switch for load. Press and hold for 5 seconds to restore factory settings.

4. Installation

Proper installation is crucial for the safe and efficient operation of your solar charge controller. Please follow these steps carefully:

  1. Prepare Tools and Materials: Gather all necessary installation tools and cables. Ensure cables are of suitable gauge to prevent excessive voltage drop (current density should be less than 4A/mm²).
  2. Select Installation Site: Choose an installation site that meets relevant safety requirements. Avoid damp, dusty, flammable, explosive, and corrosive gas environments.
  3. Mount the Controller: Install the controller fixed to a vertical plane. Refer to the mounting aperture and hole spacing in the manual (not provided in this extract, but typically found in a full manual). To ensure good cooling, reserve at least 10cm of space below the controller.
  4. Wiring Sequence: Connect the load, battery, and solar panel to the controller in the correct sequence. Ensure that the polarity of the load, battery, and solar panel matches the controller's terminals.
A simplified wiring diagram showing the connection points for solar panels, battery, and load to the controller's terminals (1-6).
Figure 4.1: Basic Wiring Diagram
An annotated diagram of the controller's terminals, clearly marking the Solar Panel Terminal, Battery Terminal, and Load Terminal, along with the USB port and Temp. Sensor input.
Figure 4.2: Controller Terminal Layout
A comprehensive system connection diagram illustrating how the solar panels, battery, controller, inverter, DC loads, and AC loads are interconnected in a solar power system.
Figure 4.3: Full System Connection Diagram
  1. External Temperature Sensor: Before use, insert the external temperature sensor probe into the left temperature probe interface of the controller. Place the probe in a location with similar battery temperature. This ensures accurate temperature compensation for charging parameters.
  2. Safety Warning: To prevent accidents, installation and maintenance should only be performed by qualified professionals.

5. Operating Instructions

5.1. LCD Display and Parameter Monitoring

The LCD display provides real-time data on your solar system's performance. You can monitor parameters such as solar charging current, ambient temperature, load current, battery capacity, and various voltage levels. Use the 'Toggle key' to cycle through different display screens.

5.2. Setting Operating Modes and Parameters

The controller supports a three-time control mode for load output, which can be configured by the user:

  • Evening (A): Working time after dark (dusk).
  • Interval (B): Rest or pause time between working periods.
  • Dawn (C): Working time during morning light function.

To set these parameters:

  1. Use the 'Toggle key' to navigate to the desired parameter setting.
  2. Use the '+' and '-' buttons to adjust the values (e.g., hours for evening, interval, and dawn working times).
  3. Confirm your settings by pressing the 'Toggle key' again or waiting for the display to auto-save.

Load Output State Settings:

  • 00H: Light control mode; load opens after dark (dusk) and stops working after dawn.
  • 24H: Normal open mode; load remains on until battery voltage protection disconnects it.
  • 01H-23H: User-defined working hours. For example, 01H to 23H means the load is disconnected for a few hours, and the evening load operates for the set duration.

Function Keys for Setting and Saving:

  • Toggle key: Used to switch between display modes and confirm settings.
  • '+' / '-' buttons: Used to increase or decrease parameter values.
  • ON/OFF/RESET button: Press to manually switch the load ON/OFF. Press and hold for 5 seconds to restore factory settings.

6. Maintenance

To ensure the longevity and optimal performance of your PowMr Solar Charge Controller, regular maintenance is recommended:

  • Keep Clean: Periodically clean the controller's exterior to prevent dust accumulation, especially on the heat sink fins, which can impede cooling.
  • Check Connections: Regularly inspect all wiring connections (solar panel, battery, load) to ensure they are tight and free from corrosion. Loose connections can lead to power loss or system malfunction.
  • Environmental Conditions: Ensure the controller remains in a dry, well-ventilated area, away from direct sunlight, moisture, and extreme temperatures.
  • Battery Health: Monitor your battery's health and ensure it is properly maintained according to the battery manufacturer's guidelines.

7. Troubleshooting

If you encounter issues with your solar charge controller, refer to the following common problems and their solutions:

  1. Solar Panels Not Charging / Charging Failure:
    • Problem: Incorrect polarity of solar panel cables ('+' and '-').
    • Solution: Remove the cables and re-install them with the correct polarity.
    • Problem: Solar panel power exceeds the rated power of the controller.
    • Solution: Reduce the solar panel power to not exceed the controller's rated capacity.
  2. Load Not Discharging / Discharge Failure:
    • Problem: Load is not properly connected.
    • Solution: Re-install the load with correct connections.
    • Problem: Load power exceeds the rated power of the controller.
    • Solution: Reduce the load power to not exceed the controller's rated capacity.
    • Problem: Instantaneous starting current is too large, or battery capacity is too small.
    • Solution: Replace with higher-capacity batteries. Use the ON/OFF/RESET button to troubleshoot.
  3. Loose or Inadequate Wiring:
    • Problem: Wire cables are loose or too thin.
    • Solution: Re-tighten connections and ensure appropriate cable gauge (AWG) is used.
  4. General Faults / Resetting:
    • Problem: Unspecified system error or parameter issues.
    • Solution: Press and hold the ON/OFF/RESET button for 5 seconds to restore factory settings. This can resolve many common faults.

8. User Tips

Here are some helpful tips for getting the most out of your PowMr Solar Charge Controller:

  • Versatile Applications: This controller is highly versatile and can be effectively used in various scenarios, including lighting control, comprehensive solar system management, precise charging control, voltage regulation, thermal management, and collector control.
  • Current Capacity: Always ensure your system's current requirements match the controller's capacity. The L60A model handles up to 60A, while the L80A model supports up to 80A. Choosing the correct model for your setup is crucial for optimal performance and safety.
  • Smart Features: Take advantage of the controller's smart device capabilities for enhanced monitoring and control, if integrated with compatible systems.
  • Certifications: The CE and RoHS certifications indicate that the product meets high standards for safety and environmental compliance.

9. Frequently Asked Questions (FAQ)

Q: Under which categories does this product fall?
A: This product falls under several categories including lighting controllers, solar system controllers, charger controllers, voltage controllers, thermal controllers, and collector controllers.
Q: What's the maximum current that this product can handle?
A: It can handle maximum currents of either 60A or 80A, depending on the model number (L80 or L60).
Q: What are the benefits of using this product?
A: Using this product allows for efficient control and management of lighting, solar systems, charging, voltages, thermals, and collectors.
Q: In which scenarios can this product be used?
A: This product can be used in various scenarios such as lighting control, solar system management, charging control, voltage control, thermal control, and collector control.
Q: Can you highlight some features of this product?
A: Some notable features of this product include its RoHS and CE certifications, smart device capabilities, and versatile applications in different areas.
Q: What are the functions of this product?
A: It can function as a lighting controller, solar system controller, charger controller, voltage controller, thermal controller, and collector controller.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact the seller directly. Ensure you have your product model and purchase details available when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.