Smartour Universal Car Rear View Camera

1. Introduction

Thank you for choosing the Smartour Universal Car Rear View Camera. This camera is designed to enhance your driving safety by providing a clear view of the area behind or in front of your vehicle. It features high-definition imaging, night vision capabilities, and a wide 180-degree fisheye lens. This manual provides detailed instructions for installation, operation, and maintenance to ensure optimal performance.

2. Safety Information

• Ensure all power connections are secure and correctly insulated to prevent short circuits.
• Disconnect the vehicle's battery before performing any electrical work.
• Professional installation is recommended for complex wiring or drilling.
• Do not obstruct the camera's view with dirt, snow, or ice. Clean regularly.
• This camera is an aid for parking and reversing; always check your surroundings manually.

3. Package Contents

Please check the package for the following items:

• Car Camera (AHD 1080P or CVBS 720P, depending on selection)
• Video Cable (6M length)
• Power Cable
• Adapter Cable (for specific connections)

Illustration of the components included in the package.

4. Specifications

5. Setup and Installation

5.1 Choosing Installation Location

The camera can be installed in either the front or rear of your vehicle. Common locations include the license plate area for rear view or the front grille for front view. Ensure the chosen location provides a clear, unobstructed view.

Example installation locations for front and rear views.

5.2 Physical Installation (Punching)

The camera requires an 18.5mm diameter hole for flush mounting. Use a suitable drill bit to create the hole in the chosen location. Carefully insert the camera and secure it with the provided clips.

Camera dimensions for drilling: 18.5mm diameter.

5.3 Wiring Diagram

Follow the wiring diagram carefully to connect the camera to your vehicle's power and display unit. Ensure all connections are secure.

Wiring Diagram: Connect the video cable (yellow RCA) to your monitor's video input (B). The trigger wire (A) from the video cable connects to the reversing light positive. The camera's power cable (red/black) connects to the reversing light positive (red) and vehicle ground (black).

5.4 System Configuration (AHD/CVBS Selection)

If your car's display system supports AHD, you may need to configure it to recognize the AHD 1080P signal. If AHD cannot be selected, your system may not support it, and you should use the CVBS-NTSC setting.

1. Go to your car's display unit settings.
2. Navigate to Car Settings >> Factory Settings >> HD Reversing Settings.
3. Select either CVBS-NTSC or AHD 1080P based on your camera model and display unit compatibility.

Example of system settings for selecting video signal type.

6. Operating Instructions

6.1 Front/Rear View Switching

The camera supports switching between front and rear view modes. This is typically controlled by cutting a specific wire (often green) on the camera's control line. Refer to the control line diagram for details.

Control line diagram for adjusting camera functions.

6.2 Parking Line Control

The camera can display parking guidelines on the screen. These lines can be enabled or disabled by cutting a specific wire (often white) on the camera's control line. Refer to the control line diagram.

Example of parking lines displayed on the monitor.

6.3 CVBS/AHD 1080P Switch

If your camera supports both CVBS and AHD 1080P, you can switch between these video signal types by cutting a specific wire (often blue) on the camera's control line. Ensure your display unit is compatible with the selected signal type.

6.4 Night Vision

The camera features low-light level night vision for improved visibility in dark conditions. The night vision activates automatically when light levels are low.

Comparison of daytime and night vision display quality.

7. Maintenance

• Cleaning: Regularly clean the camera lens with a soft, damp cloth to ensure a clear view. Avoid abrasive cleaners.
• Waterproofing: The camera is IP67 waterproof. However, avoid high-pressure water jets directly on the camera to prevent potential damage over time.
• Cable Inspection: Periodically check all cables for wear, damage, or loose connections.

8. Troubleshooting

• Image is upside down or reversed: Check the camera's control lines. There might be a wire (e.g., green line) that controls image orientation. Cutting or connecting this wire can flip the image.
• No image on screen:
  • Ensure all power and video cables are securely connected.
  • Verify the camera is receiving 12V DC power.
  • Check your display unit's input settings to ensure the correct video source is selected (e.g., AV-in, Camera).
  • Confirm the video signal type (AHD or CVBS) matches your display unit's capabilities and the camera's setting (blue control line).
• Parking lines not appearing: Ensure the white control line for parking lines is configured correctly (cut or uncut as per desired state).
• Dynamic parking lines not working: This camera provides static parking lines. Dynamic lines that move with the steering wheel are a feature of the car's head unit, not the camera itself. Your head unit must support this function and be correctly configured.

9. User Tips

• Compatibility Check: Before installation, verify that your car's head unit or display supports either AHD 1080P or CVBS NTSC video signals. Some older units may only support CVBS.
• Wiring for Android Units: When connecting to an Android head unit, ensure the video input is correctly identified and selected in the unit's settings, often under 'Backcar Setting' or 'HD Reversing Settings'.
• Test Before Finalizing: It is highly recommended to test the camera's functionality and image orientation before fully securing all components and reassembling vehicle panels.

10. Warranty and Support

For warranty information or technical support, please contact the seller or refer to the product listing where you purchased the camera. Keep your purchase receipt as proof of purchase.