NERIES Display Holder Bracket

Contents

Electric Bicycle LCD Instrument Holder Bracket User Manual

Brand: NERIES

Model: Display Holder Bracket

1. Introduction

Thank you for choosing the NERIES Electric Bicycle LCD Instrument Holder Bracket. This bracket is designed to securely mount your electric bicycle's LCD instrument, such as the SL-100 display, to your bicycle handlebars. Made from durable ABS plastic, it offers fine workmanship, wear-resistance, and easy installation, enhancing your cycling experience.

2. Safety Information

Please read and understand all safety information before installing and using this product. Failure to follow these instructions may result in damage to the product, your bicycle, or personal injury.

  • Ensure all screws are tightened securely to prevent the display from detaching during use.
  • Do not overtighten screws, as this may damage the bracket or your bicycle's handlebars.
  • Regularly check the bracket for any signs of wear or damage. Replace if necessary.
  • Keep small parts, such as screws, out of reach of children.

3. Package Contents

Please verify that all items are included in your package:

  • 1 x Display Holder Bracket
  • Mounting Screws (typically 2 for the display, 2 for the clamp)
Close-up view of the NERIES Display Holder Bracket and its included mounting screws.
Figure 1: Display Holder Bracket and Mounting Screws

4. Specifications

FeatureDetail
BrandNERIES
ModelDisplay Holder Bracket
MaterialABS Plastic
Overall Dimensions (H x W)Approximately 50mm x 24.5mm
Handlebar Clamp Diameter22.5mm
Display Mounting Plate Width24.5mm
Display Mounting Plate Depth14mm
Offset from Clamp to Plate12mm
Weight26g
CompatibilitySL-100 Instrument and similar displays
Detailed diagram showing the dimensions of the display holder bracket, including height, width, and clamp diameter.
Figure 2: Product Dimensions

5. Setup and Installation

Follow these steps to install the display holder bracket on your electric bicycle:

  1. Prepare Your Handlebars: Identify a suitable location on your handlebars for the display. Ensure there is enough space and that the display will be easily visible and accessible. The bracket is designed for handlebars with a 22.5mm diameter.
  2. Attach the Bracket to Handlebars: Loosen the screws on the clamp part of the holder bracket. Position the bracket around your handlebar at the desired location. Tighten the screws evenly until the bracket is secure and does not rotate freely. Do not overtighten.
  3. Mount the LCD Instrument: Align the mounting holes on your LCD instrument (e.g., SL-100) with the screw holes on the flat plate of the holder bracket. Use the provided screws to attach the display to the bracket. Ensure the display is oriented correctly and tighten the screws firmly.
Image showing the display holder bracket installed on a handlebar, with an LCD instrument attached.
Figure 3: Bracket with Display Installed (Front View)
Top-down view of the display holder bracket with an LCD instrument mounted, showing the secure attachment.
Figure 4: Bracket with Display Installed (Top View)
Bottom-up view of the display holder bracket with an LCD instrument mounted, showing the cable routing.
Figure 5: Bracket with Display Installed (Bottom View)

6. Operating Instructions

This product is a passive holder bracket. Once installed, it requires no further operation. Its function is to securely hold your electric bicycle's LCD instrument in place, allowing you to view your display while riding.

7. Maintenance and Care

  • Cleaning: Wipe the bracket with a soft, damp cloth to remove dust and dirt. Avoid using harsh chemicals or abrasive cleaners, as these may damage the ABS plastic.
  • Inspection: Periodically check all mounting screws to ensure they remain tight. Inspect the bracket for any cracks, deformities, or signs of wear. If any damage is observed, replace the bracket to ensure the safety of your display.
  • Storage: If removing the bracket for storage, keep it in a cool, dry place away from direct sunlight and extreme temperatures.

8. Troubleshooting

  • Display feels loose: Check if the screws attaching the display to the bracket are tight. If they are, ensure the bracket's clamp screws on the handlebar are also secure.
  • Bracket rotates on handlebar: The clamp screws may not be tight enough, or the handlebar diameter might be slightly smaller than 22.5mm. Ensure screws are tightened firmly. If the handlebar is too small, consider using a thin rubber shim (not included) to create a tighter fit.
  • Display does not fit the bracket: Verify that your LCD instrument's mounting holes and dimensions are compatible with the bracket's mounting plate (24.5mm width, 14mm depth, 3mm screw hole spacing). This bracket is specifically designed for SL-100 instruments or similar.

9. User Tips

No specific user tips are available from customer reviews or Q&A at this time. Always ensure a snug fit for both the handlebar and the display to prevent movement during rides.

10. Warranty and Support

For any questions, concerns, or support regarding your NERIES Display Holder Bracket, please contact the seller or retailer from whom you purchased the product. They will be able to provide assistance with product-specific inquiries, returns, or warranty claims in accordance with their policies.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.