1. Introduction
The NISSEI RS-101 is a high-quality SWR & Power Meter designed for shortwave radio applications, covering a frequency range of 1.8 to 60 MHz. It features a large, easy-to-read LED-backlit display and supports power measurements up to 3KW with selectable ranges. This manual provides essential information for the proper setup, operation, and maintenance of your device.

2. Package Contents
Please check the package for the following items:
- NISSEI RS-101 SWR & Power Meter
- User Manual (English)
- Power Cable (12V DC)

3. Controls and Indicators
Familiarize yourself with the front panel controls and the rear panel connections:
Front Panel

- Meter Display: Large analog meter for SWR and Power readings. Features LED backlight for improved visibility.
- FUNCTION Knob: Selects measurement mode (FWD, REV, SWR SET).
- RANGE Knob: Selects power measurement range (30W, 300W, 3KW).
- PEP/AVG Button: Toggles between Peak Envelope Power (PEP) mode (for SSB) and Average (AVG) mode (for FM).
- SWR SET Knob (MIN/MAX): Used for SWR calibration.
Rear Panel

- 12V DC Power Input: Connect the provided power cable here. This powers the LED backlight.
- ANT Connector: Connect your antenna to this port.
- TX Connector: Connect your transceiver (radio) to this port.
4. Setup and Connection
- Power Connection: Connect the provided 12V DC power cable to the '12V DC' input on the rear panel. Ensure correct polarity: the black wire is negative, and the black and white wire is positive. The external power supply is primarily for the LED backlight function and does not affect measurement accuracy.
- Antenna Connection: Connect your antenna cable to the 'ANT' connector on the rear panel.
- Transceiver Connection: Connect your transceiver's output to the 'TX' connector on the rear panel.

5. Operating Instructions
5.1 Power Measurement
- Set the FUNCTION knob to 'FWD' (Forward Power) or 'REV' (Reverse Power) as desired.
- Select the appropriate power range using the RANGE knob (30W, 300W, or 3KW) based on your transceiver's output.
- Press the PEP/AVG button to select the desired measurement mode:
- AVG (Average) Mode: When the orange button is popped out, it's suitable for continuous wave (CW) or Frequency Modulation (FM) modes.
- PEP (Peak Envelope Power) Mode: When the orange button is pressed in, it's ideal for Single Sideband (SSB) transmissions to measure peak power.
- Transmit a signal from your transceiver. The meter will display the forward or reverse power.
5.2 SWR Measurement and Calibration
To accurately measure Standing Wave Ratio (SWR), calibration is required:
- Set the FUNCTION knob to 'SWR SET'.
- Turn the SWR SET knob (MIN/MAX) fully counter-clockwise to the 'MIN' position.
- Transmit a continuous signal from your transceiver (e.g., a carrier wave).
- While transmitting, slowly adjust the SWR SET knob clockwise until the meter pointer reaches the 'CAL' mark (full scale) on the display.
- Once calibrated, switch the FUNCTION knob to 'SWR'. The meter will now directly display the SWR reading.


6. Specifications
| Feature | Specification |
|---|---|
| Frequency Range | 1.8 - 60 MHz |
| Power Measurement Range | 30W / 300W / 3KW (selectable) |
| Measurement Modes | Average (AVG), Peak Envelope Power (PEP) |
| Display Type | Analog Pointer Meter with LED Backlight |
| Input/Output Connectors | UHF (SO-239 type) |
| Power Supply | 12V DC (for backlight) |
| Dimensions (L x W x H) | 190mm x 105mm x 80mm |


7. Maintenance
The NISSEI RS-101 is designed for reliable operation with minimal maintenance. To ensure its longevity and accurate performance:
- Keep the device clean and free from dust. Use a soft, dry cloth for cleaning.
- Avoid exposing the unit to extreme temperatures, humidity, or direct sunlight.
- Do not attempt to open the casing or perform internal repairs, as this may void any potential warranty and could damage the sensitive internal components.
8. Troubleshooting
If you encounter issues with your NISSEI RS-101, consider the following basic troubleshooting steps:
- No LED Backlight: Check the 12V DC power connection and ensure correct polarity.
- No Meter Movement: Verify all antenna and transceiver connections are secure. Ensure the transceiver is transmitting power.
- Inaccurate Readings: Re-perform the SWR calibration process. Ensure the correct power range is selected.
If problems persist, please contact your seller for further assistance.
9. Warranty and Support
For warranty information and technical support, please refer to the terms provided by your original point of purchase or contact the seller directly. Keep your purchase receipt as proof of purchase.