1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your new Usongshine Laser Air Assist System. This system is designed to significantly improve the performance of your laser engraver by providing a strong, focused airflow to the laser's focal point. This helps to blow away smoke and debris, resulting in cleaner cuts, sharper engravings, and reduced charring on your materials. Please read this manual thoroughly before using the product to ensure safe and efficient operation.
2. Safety Information
Please observe the following safety precautions to prevent injury or damage to the equipment:
- Always ensure proper ventilation when operating the laser engraver with the air assist system.
- Avoid direct eye or skin exposure to laser radiation. Keep children away from the operating area.
- Ensure all connections are secure before powering on the device.
- Do not attempt to disassemble or modify the air assist unit.
- The product is CE certified, indicating compliance with European safety standards.
3. Package Contents
Please check the package for the following items:
- Air Pump Unit
- Power Adapter
- Air Hose
- Mounting Bracket
- Various Screws (for mounting)
- Hex Wrenches
- Open-end Wrench
- Air Nozzle/Connector
4. Specifications
| Feature | Specification |
|---|---|
| Air Flow | 24 L/min |
| Voltage | 24V |
| Rated Power | 28W |
| Wind Speed | 3.5 m/s |
| Lifespan | 10,000 hours |
| Fan Speed | 30,000 rpm |
| Shell Size (L*W*H) | 90mm * 72mm * 51mm |
| Certification | CE |
| Smart Device | No |
| Origin | Mainland China |
5. Setup Instructions
Follow these steps to install the air assist system on your laser engraver:
-
Mounting the Air Pump Unit:
Attach the air pump unit to your laser engraver using the provided mounting bracket and screws. Refer to the images for typical mounting positions. Ensure the unit is securely fastened and does not obstruct the laser's movement.
Note: For Atom A5RPO, A10PRO, and TTS series laser engravers, installing this air assist system will reduce the Y-axis travel by approximately 6cm.
Image: The air assist unit installed on a laser engraver, showing its position relative to the laser module.
Image: A closer view of the air assist unit mounted, highlighting the connection points. -
Connecting the Air Hose:
Connect one end of the air hose to the outlet port on the air pump unit. Connect the other end of the air hose to the air nozzle/connector on your laser module. Ensure a snug fit to prevent air leakage.
-
Power Connection:
Connect the power adapter to the air pump unit and then plug it into a suitable power outlet. Ensure you use the correct plug type (US or EU) for your region.
6. Operating Instructions
Operating the air assist system is straightforward:
- Ensure the air assist system is properly installed and connected as per the setup instructions.
- Turn on your laser engraver.
- Power on the air assist unit. The fan will start, providing airflow through the nozzle.
- Begin your laser engraving or cutting job. The continuous airflow will help clear smoke and debris, leading to cleaner results and protecting your laser lens.
- After completing your job, power off the air assist unit, then power off your laser engraver.
7. Maintenance
Regular maintenance ensures optimal performance and longevity of your air assist system:
- Cleaning the Unit: Periodically wipe down the exterior of the air pump unit with a dry, soft cloth to remove dust and debris.
- Checking Air Hose: Inspect the air hose regularly for any kinks, blockages, or damage. Ensure the hose is clear to allow unrestricted airflow.
- Nozzle Inspection: Check the air nozzle for any buildup or obstructions that might impede airflow. Clean as necessary.
- Storage: When not in use for extended periods, store the air assist system in a clean, dry environment.
8. Troubleshooting
If you encounter issues with your air assist system, refer to the following table:
| Problem | Possible Cause | Solution |
|---|---|---|
| No airflow from nozzle | Power adapter not connected or faulty; Air hose kinked or blocked; Unit not powered on. | Check power connections and ensure the unit is switched on. Inspect the air hose for obstructions and straighten any kinks. Test the power adapter if possible. |
| Weak airflow | Partial blockage in air hose or nozzle; Loose connections. | Clear any partial blockages in the air hose or nozzle. Ensure all hose connections are tight. |
| Unusual noise from unit | Unit not stable; Internal component issue. | Ensure the unit is mounted securely and on a stable surface. If noise persists, contact customer support. |
9. User Tips
- For optimal results, ensure the air nozzle is positioned as close as possible to the laser's focal point without interfering with the laser beam or material.
- Regularly clean your laser engraver's lens, as the air assist system helps reduce debris but does not eliminate the need for lens maintenance.
- Always perform a small test cut or engraving on scrap material after installation or significant adjustments to verify performance.
10. Warranty and Support
For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.