NISSEI RS-502

Contents

NISSEI RS-502 Watt/SWR Meter Instruction Manual

Model: RS-502

1. Introduction

The NISSEI RS-502 is a highly accurate RF power and SWR meter designed for radio communication transceivers. It provides precise measurements of forward power (FWD), reflected power (REF), and Standing Wave Ratio (SWR) across a wide frequency range, supporting HF, VHF, and UHF bands. This manual provides essential information for the proper setup, operation, and maintenance of your RS-502 meter.

Front view of the NISSEI RS-502 SWR & Watt Meter, showing the analog display and control knobs.
Figure 1: Front View of NISSEI RS-502

2. Package Contents

Please check the package carefully to ensure all items are present:

  • 1 × NISSEI RS-502 SWR & Watt Meter
  • 1 × Operation Manual (this document)
  • 1 × 13.8V DC Wire

3. Specifications

FeatureSpecification
Frequency Range1.8 ~ 525 MHz
Measurable Power Range1 ~ 200 W
Power Ranges5 W / 20 W / 200 W
Power Measurement Error (AVG)5W Range: ±10%
20W-200W Ranges: ±5%
Power Measurement Error (REP)5W Range: ±15%
20W-200W Ranges: ±10%
SWR Minimum Input Power3 W
Impedance50 Ohm
Insertion Loss< 0.1 dB
Test Functional ItemsFWD/REF POWER, REP, SWR
Dimensions (W x H x D)190 x 85 x 135 mm
WeightApprox. 950 g
Interface TypeM or N type
ConnectorSO-239 M

4. Setup

Follow these steps to properly set up your NISSEI RS-502 meter:

  1. Power Connection: Connect the supplied 13.8V DC wire to the 'DC 13.8V' input jack on the rear panel of the meter. Connect the other end to a stable 13.8V DC power source.
  2. Transceiver Connection: Connect the output of your radio transceiver to the 'TX' connector on the rear panel of the RS-502 using a suitable coaxial cable.
  3. Antenna Connection: Connect your antenna system to the 'ANT' connector on the rear panel of the RS-502 using a suitable coaxial cable.
Rear view of the NISSEI RS-502 SWR & Watt Meter, showing the TX, ANT, and DC 13.8V connectors.
Figure 2: Rear View with Connections

Ensure all connections are secure to prevent signal loss or damage to the equipment.

5. Operation

The RS-502 features several controls for accurate power and SWR measurements:

Angled front view of the NISSEI RS-502 SWR & Watt Meter, highlighting the controls.
Figure 3: Angled Front View with Controls

5.1 Controls Overview

  • FUNCTION Knob (FWD / CAL / SWR): Selects the measurement mode.
  • POWER RANGE Switch (5W / 20W / 200W): Sets the maximum power scale for measurement.
  • BAND Switch (HF / VHF / UHF): Selects the operating frequency band.
  • PEP / AVG Switch: Selects between Peak Envelope Power (PEP) for SSB signals or Average Power (AVG) measurement.
  • CAL Knob: Used for SWR calibration.

5.2 Measuring Forward and Reflected Power

  1. Set the BAND switch to the appropriate frequency range (HF, VHF, or UHF) for your operation.
  2. Set the POWER RANGE switch to a range higher than your expected transmit power. Start with a higher range (e.g., 200W) and decrease if necessary for better resolution.
  3. Set the FUNCTION knob to 'FWD' to measure forward power.
  4. Transmit a continuous carrier (e.g., using FM or CW mode) from your transceiver. The meter will display the forward power.
  5. Set the FUNCTION knob to 'REF' to measure reflected power. The meter will display the reflected power.

5.3 Measuring SWR (Standing Wave Ratio)

  1. Set the BAND switch to the appropriate frequency range.
  2. Set the POWER RANGE switch to a range suitable for your transmit power (minimum 3W required for SWR measurement).
  3. Set the FUNCTION knob to 'FWD'.
  4. Transmit a continuous carrier. Adjust the CAL knob until the meter needle points to the 'CAL' mark on the scale.
  5. While still transmitting, switch the FUNCTION knob to 'SWR'. The meter will now display the SWR value.
  6. After measurement, release the transmit button.

5.4 PEP / AVG Measurement

For measuring power of modulated signals like SSB, use the 'PEP' setting. For continuous wave (CW) or FM signals, use the 'AVG' setting. Toggle the PEP / AVG switch accordingly.

6. Maintenance

To ensure the longevity and accuracy of your NISSEI RS-502 meter, follow these maintenance guidelines:

  • Cleaning: Use a soft, dry cloth to clean the exterior of the meter. Do not use abrasive cleaners or solvents, as they may damage the finish or display.
  • Storage: Store the meter in a dry, dust-free environment when not in use. Avoid extreme temperatures and direct sunlight.
  • Connections: Periodically check all coaxial cable connections for tightness and corrosion. Loose or corroded connections can affect measurement accuracy.
  • Power Supply: Ensure the 13.8V DC power supply is stable and within the specified voltage range.

7. Troubleshooting

If you encounter issues with your RS-502 meter, try the following troubleshooting steps:

  • No Meter Movement:
    • Check if the 13.8V DC power supply is connected and functioning correctly.
    • Ensure the transceiver is transmitting power.
    • Verify all coaxial cables are securely connected to the 'TX' and 'ANT' ports.
    • Confirm the POWER RANGE switch is set appropriately for the transmit power.
  • Inaccurate Readings:
    • Ensure the BAND switch is set to the correct frequency range.
    • Check for damaged or poor-quality coaxial cables and connectors.
    • Verify the antenna system is properly tuned and matched.
    • For SWR, ensure proper calibration using the 'CAL' position and knob.
  • High SWR Readings:
    • This typically indicates an issue with your antenna system (e.g., antenna not tuned, damaged antenna, or faulty feedline). The meter is accurately reflecting the antenna's performance.

8. User Tips

  • Always start SWR measurements with low power to protect your equipment, then increase power as needed for calibration.
  • For critical measurements, allow the meter to stabilize for a few moments after powering on.
  • Keep the meter away from strong magnetic fields or other RF interference sources that could affect its accuracy.

9. Warranty and Support

For warranty information or technical support, please refer to the documentation provided by your retailer or contact the manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.