1. Important Safety Information & Warnings
Please read this manual carefully before using your radio. Failure to follow these instructions may result in injury or damage to the radio.
General Warnings
- Do not communicate or charge this radio in flammable, explosive areas (e.g., oil stations, gas stations, airports).
- Do not operate this radio without a license in government-banned areas.
- Avoid direct sunlight and proximity to heating devices.
- Keep the radio away from dusty, humid, and water-splashed places.
- If the radio smells or smokes, immediately remove the battery pack and contact your nearest distributor.
- Self-disassembly or repair by non-professionals is prohibited.
RF Energy Exposure & Product Safety
This two-way radio uses electromagnetic energy. It is designed, manufactured, and tested to meet government-established RF exposure levels. To ensure compliance, adhere to the following:
- Transmit no more than 50% of the total radio use time. Transmitting for longer periods may exceed RF exposure compliance requirements.
- Hold the radio in a vertical position with the microphone at least 2.5 cm (1 inch) away from your nose or lips. Keep the antenna away from your eyes.
- Use only Retevis-approved accessories (clip, holder, holster, case, or body harness) to ensure compliance with RF exposure limits.
- Do not operate the radio without a proper antenna attached. A damaged antenna can cause minor burns if it contacts the skin.
Battery Safety
- Turn off the radio before removing or installing the battery, or when charging.
- Do not disassemble the charger.
- Do not operate the charger if it has been broken or damaged.
- Avoid short-circuiting battery terminals with conductive materials (jewelry, keys, chains) to prevent burns.
Hearing Protection
- Use the lowest volume necessary.
- Turn down the volume before adding a headset or earpiece.
- Limit the amount of time using headsets or earpieces at high volume.
- Do not place the radio's speaker directly against your ear when not using a headset or earpiece.
Choking Hazard
This product contains small parts. Keep away from children under 3 years old.
2. Package Contents
Carefully unpack your radio and check for the following items. If any item is missing or damaged, please contact your seller.
| Item Name | Quantity |
|---|---|
| Two-Way Radio Host (RB629/RB29) | 2 |
| Battery | 2 |
| Belt Clip | 2 |
| Hand Strap / Sling | 2 |
| Desktop Charger | 2 |
| Screws | 4 |
| User's Manual | 1 |
Visual representation of the package contents:


3. Getting Started
3.1 Battery Installation and Charging
The battery is not fully charged at the factory. Please charge it before first use. For new batteries or those stored for over two months, it may take two or three charge/discharge cycles to reach full operating capacity.
- To Install: Align the battery with the positioning hole at the radio's bottom, then press the battery until the button locks it completely.
- To Remove: Turn off the radio. Push up the battery button on the radio top, then remove the battery.


Charging: Place the radio in the desktop charger. The radio supports USB charging methods.

Notice: Once the battery is fully charged, remove it from the charger to prevent overcharging and damage to battery life.
3.2 Installing the Belt Clip
Attach the belt clip to the back of the battery using the supplied screws for convenient carrying.
3.3 Installing Earphone/Programming Jack
Uncover the earphone lid and insert earphones (purchased separately) directly into the earphone holes.

The radio can be programmed using computer software. Consult your local dealer for information on programming software.
4. Basic Operations
4.1 Getting Acquainted with Your Radio


- Antenna: For transmitting and receiving signals.
- LED Indicator Light: Red when transmitting, green when receiving.
- Speaker: Outputs audio.
- Microphone: For speaking.
- Channel-selecting Knob: Rotate to select channels 1-16. Clockwise increases channel number, counter-clockwise decreases. An alert tone sounds if an empty channel is selected.
- Power/Volume Knob: Rotate clockwise to power on, counter-clockwise to power off (until a click is heard). Controls volume.
- PTT Switch (Push-to-Talk): Press to transmit, release to receive. The indicator light turns red during transmission. If no transmitting frequency, a "Du Du" tone sounds.
- Side-key: Customizable via software (e.g., null, VOX, emergency alarm, scan, busy lock). Default: short press for scan, long press for VOX.
- Moni Switch (Monitor): Press to monitor calls with different mute tones or to listen when the signal strength is below the opening threshold.
4.2 Key Features & Functions
- VOX (Voice Operated Exchange): Allows hands-free communication. Speak into the microphone to transmit directly without pressing the PTT switch. The radio stops transmitting when no voice is detected. Ensure VOX gain is set appropriately to avoid accidental transmission or missed voice.
- Squelch Level: Determines the signal strength required to open the speaker. A lower squelch level increases communication range but may pick up more background noise. Default is 3 (adjustable 0-9 via software).
- Time Out Timer (TOT): Prevents continuous transmission for too long, protecting the radio from damage. If transmission exceeds the pre-set time, the radio stops and an alert tone sounds. Release PTT to reset.
- Scan On/Off: If enabled via software, rotating the channel knob to channel 16 initiates scanning of all scannable channels (1-16). The radio stops on a channel with a signal for communication. Note: Scanning requires at least 2 scannable channels.
- Busy Channel Lockout (BCLO): Prevents transmission on a busy channel. If BCLO is set, pressing PTT on a busy channel will result in a "Di" sound.
- QT/DQT (Quiet Talk/Digital Quiet Talk): Allows the speaker to open only when receiving a signal with the same QT/DQT code. Configurable via programming software.
- One-Key Frequency Copy: Allows copying the channel frequency and sub-tone from another radio (even different brands/models) without programming software. Press PTT and Moni switch on channel 1 simultaneously to enter copy mode.
- Wireless Copy (All Channels): Allows wireless data transmission of all channel frequencies and CTCSS/DCS codes between walkie-talkies without programming software. This feature only supports walkie-talkies with the same solution. Press PTT and Moni switch on channel 2 simultaneously to initiate.




4.3 Long-Range Communication
The RB629/RB29 series offers strong signal penetration and long-range communication capabilities:
- Open Area: 0-4 km
- City Area: 0-2.4 km
- Building: 0-30 floors


4.4 Product Video
Watch this video for a visual overview of the product and its features:
Product demonstration and feature overview.
5. Specifications
| General Specifications | |
|---|---|
| Brand Name | RETEVIS |
| Model Number | RB629/RB29 |
| Walkie Talkie Type | Portable |
| Frequency Range | 446MHz (PMR446) / 462MHz (FRS) |
| Storage Channel | 16 |
| Maximum Range | 1.5km-3km (typical), up to 4km in open areas |
| Output Power (W) | 0.5w-3w |
| Battery Capacity (mAh) | 1100 mAh |
| Battery Included | Yes |
| Material | ABS |
| Waterproof / Water-Resistant | No |
| Is Display | No |
| Dimensions | 282*203*64mm / 11.1*7.9*2.5inch (Package) |
| Origin | Mainland China |
| Certification | CE, FCC |
| Detailed Specifications | |
|---|---|
| Rated Voltage | 3.7V DC |
| Frequency Stability | ±0.5ppm |
| Antenna Impedance | 50 Ω |
| Operation Temperature Range | -30°C ~ +60°C |
| Transmitter | |
| RF power | <2W |
| Modulation type | 16kQF3E |
| Modulation distortion | <5% |
| Adjacent channel power | >65dB |
| Audio response | +6.5~-14dB |
| Max FR. Deviation | <±5KHz |
| Spurious Radiation | <7.5 μW |
| Current | <1200mA |
| Modulation Noise | <-40dB |
| Receiver | |
| Intermediation sensitivity | 8-12mv |
| Receiving sensitivity | 0.2μV |
| Adjacent channel selectivity | 65dB |
| Occupied Bandwidth | <16KHz |
| Current | Standby 55mA, working 150mA |
| Reference Frequency | 26.000MHz |
| Inter-modulation | ≥60dB |
| Spurious | ≥55dB |
| Audio response | +7~-12.5dB |
| Audio distortion | <5% |
| Audio power | 500mW |
Note: Specifications are subject to change without notice due to technical improvement.
6. Troubleshooting Guide
If you encounter any issues with your radio, refer to the table below for common problems and solutions.
| Trouble | Solution |
|---|---|
| No Electrical Source |
|
| Operating time becomes short, even if the battery is fully charged. | Replace the battery. |
| Not able to communicate with transceivers of the same group. |
|
| Voice of another group can be heard. | Change all QT/DQT of the group. |
| Other radios cannot receive TX signals or receive signals in low volume. |
|
| Noise is always heard. |
|
7. User Tips
- Compatibility: The RB629 (PMR446) and RB29 (FRS 462MHz) models operate on different frequency bands. Ensure you are using compatible radios for communication. The one-key frequency copy feature can help match frequencies with other PMR446 or FRS radios, even from different brands, but full compatibility may depend on specific sub-tones (CTCSS/DCS).
- Charging Options: While the product comes with a desktop charger, the USB charging capability offers flexibility. Consider using a multi-port USB charger for convenience if you have multiple units.
- VOX Sensitivity: If using the VOX function, adjust the VOX gain carefully. Too high sensitivity might cause accidental transmissions from background noise, while too low might miss your voice.
- Range Optimization: For optimal range, especially in urban or obstructed environments, ensure the antenna is clear and unobstructed. In open areas, the radio can achieve its maximum range.
8. Maintenance
- Cleaning: Wipe the radio surface with a soft, damp cloth. Do not use harsh chemicals or solvents.
- Storage: Store the radio in a cool, dry place away from direct sunlight, extreme temperatures, and humidity. Remove the battery if storing for extended periods.
- Battery Care: Avoid overcharging or fully discharging the battery frequently to prolong its lifespan.
- Antenna: Do not bend or modify the antenna. A damaged antenna can affect performance and safety.
9. Warranty and Support
Guarantee Information
Most new Retevis products carry a two-year manufacturer's warranty from the date of purchase. For detailed warranty terms and conditions, please visit www.retevis.com/after-sale/.
To claim warranty service, you will need to provide a receipt or proof of purchase from the actual seller for verification. You can contact the seller where you purchased the product or a Retevis Local Repair Center.
Exclusions from Warranty Coverage:
- Damage caused by accident.
- Misuse, abuse, or unauthorized alterations/repairs.
- Altered, defaced, or removed serial numbers.
Additional Resources
For downloading further resources such as brochures, software/firmware, or the full user manual in PDF format, please contact your direct reseller or visit www.retevis.com and check the "support" section for your product. A PDF version of this manual is available at this link.
10. Regulatory Information
FCC Requirements (United States)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CE Requirements (European Union)
Shenzhen Retevis Technology Co., Ltd. declares that the radio equipment type is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU, ROHS Directive 2011/65/EU, and WEEE Directive 2012/19/EU. The full text of the EU declaration of conformity is available at www.retevis.com.
This product can be used in all EU countries and regions. For specific frequency restrictions, refer to the package or manual section.
IC Requirements (Canada)
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Radio License
Business two-way radios operate on frequencies regulated by local radio management departments. To transmit on these frequencies, you may be required to have a license. Contact your local government radio management department for details.
Disposal
The crossed-out wheeled-bin symbol indicates that in the European Union, all electrical and electronic products, batteries, and accumulators must be taken to designated collection locations at the end of their working life. Do not dispose of these products as unsorted municipal waste. Dispose of them according to the laws in your area.