1. Introduction
The WM700 Digital Wood Moisture Meter is a versatile and precise instrument designed for measuring the moisture content of various materials, primarily wood and building materials. Featuring a high-definition LCD with backlight, a high-sensitivity probe, and a datum test point for calibration, this device ensures reliable and accurate readings for professionals and DIY enthusiasts alike. Its compact size and robust double injection molding make it durable and easy to carry.

Figure 1: WM700 Digital Wood Moisture Meter
2. Package Contents
Upon opening your WM700 Digital Wood Moisture Meter package, please ensure all the following items are present:
- 1 x WM700 Wood Moisture Meter
- 1 x User Manual
- 1 x Protective Carrying Bag
- 1 x Product Box

Figure 2: WM700 Package Contents
Video 1: Unboxing and initial overview of the WM700 Digital Wood Moisture Meter.
3. Setup
3.1 Battery Installation
- Locate the battery compartment cover on the back of the device.
- Slide or open the cover.
- Insert two (2) 1.5V AAA batteries, ensuring correct polarity (+/-).
- Close the battery compartment cover securely.
3.2 Probe Protection Cap
The device comes with a protective cap for the electrode pins. Remove this cap before taking measurements and replace it after use to protect the pins from damage and prevent injury.
4. Operating Instructions
4.1 Power On/Off
- To power on the device, press the MODE button briefly.
- The device features an automatic shutdown function and will power off after approximately 10 minutes of inactivity to conserve battery life.
- To restart after automatic shutdown, briefly press the MODE button again.
4.2 Display Overview

Figure 3: Function and Panel Description
The LCD display provides the following information:
- 1. Range indication (MAT): Indicates the currently selected material group.
- 2. Temperature and humidity value: Displays ambient temperature or humidity.
- 3. Test display value: Shows the measured moisture content.
- 4. Battery undervoltage indication: Alerts when batteries are low.
- 5. Temperature measurement unit: Displays ℃ or ℉.
- 6. Analog value display: A bar graph representation of the moisture level.
- 7. Measurement unit: Displays % for moisture content.
4.3 Ambient Temperature and Humidity Display
After powering on, briefly press the MODE button to cycle through the display modes. One mode will show the current ambient temperature and humidity. Press the SET button to switch the temperature unit between Celsius (℃) and Fahrenheit (℉).

Figure 4: Ambient Temperature and Humidity Display
4.4 Moisture Measurement
- Remove the protective cap from the electrode pins.
- Select the appropriate material group using the MODE button. Refer to the 'Material Parameters' table below.
- Firmly press the electrode pins into the surface of the material you wish to measure. Ensure good contact.
- Read the moisture content percentage (%) directly from the LCD.
- After measurement, carefully withdraw the pins and replace the protective cap.

Figure 5: Measuring Wood Moisture Content

Figure 6: Measuring Anhydrous Gypsum Mortar Moisture Content
4.5 Material Parameters
For accurate measurements, select the correct material group (MAT) corresponding to the material being tested:
| Range | Material | Moisture (%) |
|---|---|---|
| 1 | Beech, spruce, larch, birch, cherry, walnut | 8.8–54.8% |
| 2 | Oak, Pine, Maple, Ash, Douglas fir, Willow, Eucalyptus | 7.0–47.9% |
| 3 | Cement mortar layer and concrete | 0.9–22.1% |
| 4 | Anhydrous gypsum mortar layer | 0.0–11.0% |
| 5 | Cement mortar | 0.7–8.6% |
| 6 | Limestone slurry and gypsum | 0.6–9.9% |
| 7 | Brick | 0.1–16.5% |
Table 1: Material Measurement Ranges
4.6 Datum Test Point
The instrument cover includes a built-in test board (labeled T and B) that allows the user to verify the accuracy of the meter's datum point. This feature helps prevent errors during detection by ensuring the instrument is functioning correctly. To perform a datum point test, remove the protective cap and press the pins into the designated test points on the cap. The display should show a specific reference value (e.g., T-52% / B-27%±5%) as indicated in the manual or on the cap itself.

Figure 7: Datum Point Test
5. Maintenance
- Cleaning: Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Probe Care: Keep the electrode pins clean and free from debris. Always replace the protective cap after use to prevent bending or dulling of the pins.
- Storage: Store the meter in a dry environment within the specified storage temperature range of -10℃ to 60℃. If storing for extended periods, remove the batteries to prevent leakage.
- Battery Replacement: Replace batteries when the low battery indicator appears on the display to ensure accurate readings.
6. Troubleshooting
- No Display/Device Not Turning On:
- Check if batteries are installed correctly.
- Replace with fresh 1.5V AAA batteries.
- Ensure the power button is pressed firmly.
- Inaccurate Readings:
- Ensure the correct material group (MAT) is selected for the material being tested.
- Verify the electrode pins are making firm and proper contact with the material.
- Perform a datum point test using the protective cap to check the meter's calibration.
- Ensure the electrode pins are clean and not bent or damaged.
- Display is Dim or Flickering:
- This usually indicates low battery. Replace the batteries.
7. Specifications
| Parameter | Value |
|---|---|
| Protection level | IP20 |
| Electrode length | 10mm |
| Measuring range (Wood) | 1~75% |
| Measuring range (Building material) | 0.1~2.4% |
| Measuring range (Ambient temperature) | -10~60℃ |
| Measuring range (Environmental relative humidity) | 0-100% |
| Resolution power | 0.1%, 0.1℃, 1%RH |
| Error (1-75%) | ±5% |
| Ambient temperature error (0-45℃) | ±1% |
| Ambient temperature error (-10-0℃, 45-60℃) | ±1.5% |
| Ambient humidity error (20-80%RH) | ±4.0%RH |
| Ambient humidity error (0-20%, 80-100%RH) | ±5.0%RH |
| Automatic shutdown | About 10 minutes later |
| Measuring rate | 0.5 second |
| Storage temperature | -10~60℃ |
| Ambient temperature (use environment) | 0~40℃ |
| Relative humidity of use environment | 0-85%RH |
| Power supply | 2x1.5V AAA battery (Not included) |
| Size (including protective cap) | 147X42X25mm |
| Weight (including protective cap) | 90g |
Table 2: Technical Specifications

Figure 8: Technical Index
8. User Tips
- Choose the Right Mode: Always ensure you select the correct material group (MAT) before taking a measurement. This is crucial for obtaining accurate results, as different materials have different electrical properties.
- Firm Contact: For best results, press the electrode pins firmly and evenly into the material. Poor contact can lead to inconsistent or inaccurate readings.
- Regular Calibration Check: Utilize the built-in datum test point on the protective cap regularly to verify the meter's accuracy. This helps ensure your measurements remain reliable over time.
- Environmental Awareness: Be mindful of ambient temperature and humidity, especially when measuring materials that are sensitive to environmental conditions. The meter's ability to display these values can provide useful context.
- Protect the Probes: The high-strength stainless steel probes are durable, but always replace the protective cap when not in use to prevent damage and maintain their sharpness and integrity.
9. Warranty and Support
For any questions, technical support, or warranty inquiries regarding your WM700 Digital Wood Moisture Meter, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific contact information.