MicroZone MC6C Mini V2

Contents

MicroZone MC6C Mini V2 2.4G 6CH Remote Control Transmitter and Receiver User Manual

Model: MC6C Mini V2

Brand: MicroZone

1. Introduction

The MicroZone MC6C Mini V2 is a compact and lightweight 2.4G 6-channel remote control system designed for a wide range of RC models, including fixed-wing aircraft, drones, multirotors, helicopters, and boats. This system offers reliable control with advanced features such as runaway protection, simulation training compatibility, and long battery life. This manual provides essential information for the proper setup, operation, and maintenance of your MC6C Mini V2 remote control system.

MicroZone MC6C Mini V2 Transmitter with MC7RB-V2 Receiver and lanyard
MicroZone MC6C Mini V2 Transmitter with MC7RB-V2 Receiver and lanyard.

2. Setup

2.1 Transmitter Battery Installation

  1. Locate the battery compartment on the rear of the transmitter.
  2. Open the battery compartment cover.
  3. Insert four (4) 1.5V AA batteries or two (2) lithium batteries, ensuring correct polarity. The transmitter requires a 6V power supply.
  4. Close the battery compartment cover securely.
Diagram showing battery installation for the transmitter (4 AA batteries or 2 lithium batteries)
Transmitter battery compartment and installation options.

2.2 Receiver Connection

Connect the receiver to your model's components (servos, ESC, etc.) using the appropriate channels. The receiver provides PWM signals for individual channels and an SBUS signal for compatible flight controllers.

Standard receiver analysis for MC6RE-V2, showing SBUS, PWM signals, and binding instructions
MC6RE-V2 Receiver port layout (1 SBUS signal, 6 PWM signals).
Image of MC7RB-V2 receiver
MC7RB-V2 Receiver.

2.3 Binding Procedure (Pairing Transmitter and Receiver)

To establish communication between the transmitter and receiver:

  1. Ensure the receiver is powered on.
  2. Locate the 'BIND' button or contact point on the receiver.
  3. Press and hold the 'BIND' button/contact on the receiver.
  4. While holding the 'BIND' button, turn on the remote control transmitter.
  5. Release the 'BIND' button on the receiver once the binding process is successful (indicated by a solid LED light on the receiver).

3. Operating Instructions

3.1 Transmitter Controls Overview

Familiarize yourself with the various controls and indicators on the MC6C Mini V2 transmitter:

Detailed diagram of MC6C Mini V2 Transmitter controls and indicators
MC6C Mini V2 Transmitter Controls and Indicators.
  • Power Light: Indicates power status.
  • D/R Switch: Dual Rate switch for adjusting control sensitivity.
  • Channel 5 & 6 Switches: Auxiliary channel controls.
  • Rocker (Gimbals): Main control sticks for Aileron, Elevator, Throttle, and Rudder.
  • Trim Levers: Fine-tune control surfaces (Throttle Trim, Elevator Trim, Rudder Trim, Aileron Trim).
  • Power Switch: Turns the transmitter on/off.
  • Mode Light: Indicates the current operating mode.
  • Mode Switch: Changes between different flight modes.
  • Lock Indicator & Switch: For locking certain functions.
  • Channel Reverse Indicators: Show the current reverse status for AIL, ELE, THR, RUD.
  • V Tail Mixed Control Indicator: Indicates V-tail mixing is active.
  • Delta Wing Mixed Control Indicator: Indicates Delta wing mixing is active.
  • Hybrid Control Function Switch: Activates hybrid control.
  • Channel Forward Indicator: Indicates normal channel direction.

3.2 Channel Reverse Function

The transmitter supports channel reverse for Aileron (AIL), Elevator (ELE), Throttle (THR), and Rudder (RUD). Use the dedicated buttons to reverse the direction of these channels as needed for your model's setup.

Comparison of 6C-MINI and MC6C function switches
Comparison of 6C-MINI and MC6C function switches, highlighting the 6C-MINI's key switches with indicator lights and key lock function.

3.3 Simulation Training

The MC6C Mini V2 remote control can be connected to a computer for simulation training. This allows users to practice flying skills without risking their physical models.

Image showing simulation training with the remote control connected to a computer
Transmitter connected to a simulator for training.

3.4 Runaway Protection Settings

The system includes runaway protection. If the receiver loses signal from the transmitter or the signal strength falls below a predefined threshold, the runaway protection will activate. This feature is designed to return the model to a safe state (e.g., throttle to idle, control surfaces neutral) to prevent damage.

Runaway protection explanation with a shield icon
Runaway Protection feature for model safety.

4. Maintenance

  • Keep the transmitter and receiver clean and free from dust and moisture.
  • Avoid exposing the components to extreme temperatures or direct sunlight for prolonged periods.
  • If not using the remote control system for an extended period, remove the batteries from the transmitter to prevent leakage.
  • Regularly check all connections for security and wear.

5. Troubleshooting

  • No Power/Low Voltage Alarm: If the LED indicator flashes and the buzzer sounds, replace the transmitter batteries immediately. Ensure batteries are inserted with correct polarity.
  • Loss of Control/Signal: Re-perform the binding procedure to ensure the transmitter and receiver are properly paired. Check for potential interference sources in the operating environment. Ensure the transmitter batteries are fully charged.
  • Incorrect Control Response: Verify that all servo connections to the receiver are correct. Check channel reverse settings on the transmitter.
  • Limited Control Range: Ensure the transmitter antenna is fully extended (if applicable) and unobstructed. Check for environmental interference.

6. Specifications

6.1 Transmitter (6C-MINI)

Feature Specification
Model6C-MINI
ColorGrayish White
Number of Channels6
Applicable ModelsFixed wing, car, boat, multi-axis, lawn mower, intelligent agricultural machinery
Control Range>800m
Frequency Range2401MHz - 2478MHz
Rocker Dynamic Range80% - 120%
Fine-tuning ModeElectronic trimming
Transmit Power≤100mW
Input VoltageDC4.5-9V
Modulation ModeFSK
Power Supply Requirements4 x 1.5V AA batteries or 2 x lithium batteries
Low Voltage AlarmSupported (LED indicator and buzzer)
Analog Interface (PPM)Supported
Channel Forward/Reverse IndicationSupported
Runaway Protection SettingsSupported
LED IndicationSupported
Supported ReceiversMC6RE-V2, MC7RB-V2, MC6RE, MC7RB, MC9002, E6R-E
Dimensions (L*W*H)160mm * 80mm * 165mm
Weight470g
Certification StandardsFCC, CE_RED
Remote control specifications table for 6C-MINI
Detailed specifications for the 6C-MINI Transmitter.
Comparison of MC6C Mini V2 (470g, 160x165mm) and old MC6C (550g, 180x185mm) dimensions
Size and weight comparison between MC6C Mini V2 and the older MC6C model.

6.2 Receiver (MC6RE-V2 / MC7RB-V2)

Feature MC6RE-V2 MC7RB-V2
ModelMC6RE-V2MC7RB-V2
ColorTransparent brownTransparent brown
ApplicationFixed wing, multi-axle, car, boatFixed wing, multi-axle, car, boat
Channel Output6 PWM signals, 1 SBUS signal7 PWM signals, 1 SBUS signal
Frequency Band2401MHz - 2478MHz2401MHz - 2478MHz
Receiving Distance>800m>800m
Receiver Supply VoltageDC4.5-6VDC4.5-6V
SBUS SignalSupportSupport
Frequency-to-Frequency ModeContact pair frequencyContact pair frequency
Recovery PerformanceFast signal recoveryFast signal recovery
Runaway Protection SettingsSupportSupport
Support Remote Control6C-MINI, C7-MINI, 8B-MINI, Classic-106C-MINI, C7-MINI, 8B-MINI, Classic-10
Antenna TypeExternal antennaBuilt-in antenna
Antenna Length110mmN/A
Dimensions (L*W*H)37mm * 23mm * 13mm42mm * 30mm * 13mm
Weight7g7g
Receiver specifications table for MC6RE-V2 and MC7RB-V2
Detailed specifications for MC6RE-V2 and MC7RB-V2 Receivers.
Compatibility chart for receivers (MC6RE-V2, MC7RB-V2, MC6RE, E6R-E, MC7RB, MC9002)
Compatibility with various MicroZone receivers.

7. User Tips

  • Check Package Contents: The product may be sold as a transmitter-receiver set or individual components (e.g., 'only MC7RB-V2 RX'). Always verify your purchase to ensure you have all necessary parts.
  • Practice with Simulator: Utilize the simulation training feature to hone your control skills before flying actual models, especially for complex maneuvers.
  • Monitor Battery Levels: Pay attention to the low voltage alarm to avoid unexpected power loss during operation.
  • Understand Channel Reversing: Incorrect channel reversing can lead to unpredictable model behavior. Always test control surface directions carefully before flight.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

© 2024 MicroZone. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.