GEYA GYHO8 MTS

Contents

GEYA GYHO8 Manual Transfer Switch

Dual Power Manual Transfer Switch Interlock Circuit Breaker

1. Introduction

The GEYA GYHO8 dual power manual isolation switch is designed for reliable on-off, conversion, and isolation functions. It allows for free switching between two loads carried by a group of lines or between two power sources. This makes it an ideal product for industrial equipment and circuits requiring power switching and isolation.

The switch is constructed with a PA66 injection molded shell, ensuring high flame retardant performance. It is designed for easy and safe installation on a standard DIN rail (35×7.5).

GEYA GYHO8 Dual Power Manual Transfer Switch

Figure 1: GEYA GYHO8 Dual Power Manual Transfer Switch

2. Technical Specifications

The GEYA GYHO8 series complies with standard IEC: 60947-3.

AttributeSpecification
Rated Voltage240/415V~ (AC220/240V, 400V)
Rated Current16A, 25A, 32A, 40A, 63A, 80A, 100A, 125A
Rated Frequency50/60Hz
Number of Poles1P, 2P, 3P, 4P
Contact Form1-0-II (Three stable positions)
Electrical Life1500 Cycles
Mechanical Life10000 Cycles
Protection DegreeIP20
Ambient Temperature-5°C to 40°C
Terminal/Cable Size25mm²
InstallationMounting on 35mm DIN rail
Smart DeviceNo
Wireless FunctionalityNo
Battery IncludedNo
EU LVD VoltageLow voltage: Below 50Vac or 75Vdc

Overall Dimensions

PolesWidth (mm)Height (mm)
1P1874
2P3674
3P5474
4P7274

Note: The height values 27, 50, 63 from the OCR are likely internal component dimensions, the consistent 74mm is the overall height.

3. Safety Information

  • Always disconnect power before installing or servicing the switch to prevent electric shock.
  • Installation should be performed by a qualified electrician in accordance with local and national electrical codes.
  • Ensure all connections are tight and secure to prevent overheating and potential fire hazards.
  • Do not operate the switch if it is damaged or shows signs of wear.
  • The switch is designed for specific voltage and current ratings. Do not exceed these ratings.
  • Ensure proper grounding where applicable.

4. Installation

The GEYA GYHO8 switch is designed for DIN rail mounting (35mm). Follow the steps below for proper installation and wiring.

Wiring Steps

Refer to the video demonstration and wiring diagrams for visual guidance.

Video: GEYA GYHO8 Conversion Switch Demonstration and Wiring

  1. Access Load: Connect the load wires to the designated output terminals of the switch.
  2. Connect Power Supply: Connect the main power source wires to the 'I' input terminals and the backup power source wires to the 'II' input terminals.
  3. Secure Connections: Ensure all wires are properly inserted and screws are tightened to prevent loose connections.
  4. Mounting: Snap the switch onto a 35mm DIN rail.
  5. Insulation: Apply insulating sheets or covers as necessary to exposed terminals for safety.

Connection Diagrams

The following diagrams illustrate typical wiring configurations for single-phase and three-phase systems with stand-by generators.

Wiring Diagram for 1P and 2P GEYA GYHO8 Switches

Figure 2: Connection Diagram for 1P and 2P Switches

Single Phase and Three Phase Wiring Diagrams with Generator

Figure 3: Single Phase and Three Phase Wiring Diagrams with Stand-by Generators

Important Note: The position of incoming and outgoing wires can be adjusted according to actual needs. However, when used for dual power switching, the lower input and upper output terminals must be utilized for correct functionality.

5. Operation

The GEYA GYHO8 manual transfer switch features a front operation with three stable positions: I, 0, and II.

  • Position I: Connects to the first power source (Main Supply).
  • Position II: Connects to the second power source (Standby Supply).
  • Position 0 (Middle Position): Both power sources are disconnected, providing complete isolation.

Specific Pole Configurations:

1P Manual Transfer Switch (MTS):

  • When the handle is in the 'I' position: Terminals 1 and 2 are connected.
  • When the handle is in the 'II' position: Terminals 1 and 4 are connected.
  • When the handle is in the middle ('0') position: Both groups are disconnected.

2P Manual Transfer Switch (MTS):

  • When the handle is in the 'I' position: Terminals 1 and 2 are connected; Terminals 5 and 6 are connected.
  • When the handle is in the 'II' position: Terminals 1 and 4 are connected; Terminals 5 and 8 are connected.
  • When the handle is in the middle ('0') position: Both groups are disconnected.

3P Manual Transfer Switch (MTS):

  • When the handle is in the 'I' position: Terminals 1 and 2 are connected; Terminals 5 and 6 are connected; Terminals 9 and 10 are connected.
  • When the handle is in the 'II' position: Terminals 1 and 4 are connected; Terminals 5 and 8 are connected; Terminals 9 and 12 are connected.
  • When the handle is in the middle ('0') position: Both groups are disconnected.

4P Manual Transfer Switch (MTS):

  • When the handle is in the 'I' position: Terminals 1 and 2 are connected; Terminals 5 and 6 are connected; Terminals 9 and 10 are connected; Terminals 13 and 14 are connected.
  • When the handle is in the 'II' position: Terminals 1 and 4 are connected; Terminals 5 and 8 are connected; Terminals 9 and 12 are connected; Terminals 13 and 16 are connected.
  • When the handle is in the middle ('0') position: Both groups are disconnected.

6. Maintenance

The GEYA GYHO8 Manual Transfer Switch is designed for durability and requires minimal maintenance. However, regular checks can ensure optimal performance and safety:

  • Visual Inspection: Periodically inspect the switch for any signs of physical damage, discoloration, or loose connections.
  • Terminal Tightness: Ensure all terminal screws remain tight. Loose connections can lead to overheating.
  • Cleanliness: Keep the switch free from dust, dirt, and moisture. Use a dry, soft cloth for cleaning.
  • Operational Check: Occasionally operate the switch handle through its 'I', '0', and 'II' positions to ensure smooth mechanical action.

If any issues are observed, consult a qualified electrician for inspection and repair.

7. Troubleshooting

This section addresses common issues you might encounter with your GEYA GYHO8 Manual Transfer Switch.

  • No Power to Load:
    • Check if the switch handle is firmly in either the 'I' or 'II' position, not in the '0' (off) position.
    • Verify that both the main and standby power sources are active.
    • Inspect all wiring connections for tightness and proper contact.
    • Check upstream circuit breakers or fuses for trips or blown fuses.
  • Switch Handle is Stiff or Stuck:
    • Ensure there are no obstructions preventing the handle from moving freely.
    • Do not force the handle. If it remains stiff, there might be an internal mechanical issue. Contact a qualified electrician.
  • Overheating or Burning Smell:
    • Immediately disconnect power to the switch.
    • This indicates a serious problem, likely loose connections or an overloaded circuit. Do not attempt to fix it yourself. Contact a qualified electrician immediately.

For any complex electrical issues, always consult a professional electrician.

8. User Tips

  • Professional Installation: For safety and optimal performance, it is highly recommended to have this electrical device installed by a certified electrician.
  • Quality Product: Users have reported high satisfaction with the quality and performance of this switch, noting it offers good value.
  • Emergency Preparedness: Familiarize yourself with the operation of the switch, especially the '0' (off) position, to quickly isolate power during emergencies or maintenance.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact GEYA customer service or refer to the official GEYA website. Ensure you have your product model number (GYHO8 MTS) and purchase details available when contacting support.

10. Additional Resources

A detailed user manual in PDF format is available for download. This document provides further in-depth information and diagrams.

Download User Manual (PDF)

© 2024 GEYA. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.