1. Introduction and Warnings
Thank you for choosing the RUSHFPV RUSH MAX SOLO 5.8GHz 2.5W VTX. This video transmitter is designed for extreme long-range FPV applications, featuring robust performance and efficient cooling. Please read this manual thoroughly before operation.
1.1. Important Warnings
- The user needs to have relevant professional knowledge while mounting or operating the VTX product. Any illegal use may cause potential danger. Please ensure that you have the skills of operating FPV equipment, or operate under the guidance of a professional.
- The VTX will generate a lot of heat while working. Please ensure adequate airflow to provide a well-ventilated environment and prevent burns.
- Ensure all cables and plugs are installed correctly. Before powering up, the antenna must be installed correctly to the VTX RF output. Failure to do so will burn out the RF amplifier.
- There are a large number of precision components in the VTX. Do not disassemble, repair, or modify this product personally. Consult your dealer for technical support if the VTX malfunctions.
- Always follow local radio regulations. A HAM license may be required for operating on HAM channels or at non-HAM power levels. Some channels may require notification to local radio regulatory agencies. Ensure compliance with all local laws and regulations regarding drones and radio use.
- It is strictly forbidden to fly in restricted FPV zones such as airports, military facilities, and over crowds.
- The RF amplifier is very sensitive to SWR when operating at high power output. A damaged antenna or coaxial cable can lead to amplifier failure.
- If SmartAudio is not connected, the VTX will default to the lowest power output every time it starts.
- Do not block the airflow duct of the high-efficiency cooling fan. Ensure the VTX is mounted in a frame with good air circulation.
- The 5V output is for camera use only. Do not connect it to the power input or battery, as this will cause damage to the VTX.


2. Features
- Developed for extreme long-range pilots, featuring a compact and efficient active cooling design to unleash full VTX performance.
- LOCK-ON technology ensures jitter-free transmit channels and no sweep interference, ideal for multi-pilot flights.
- Factory power consistency calibration for all channels.
- Low noise DC-DC power supply design for clean video screens.
3. Specifications
| Parameter | Value |
|---|---|
| Channel | 48CH / 37CH (US) |
| Power Level | PIT-25mW-500mW-1000mW-MAX* |
| Input Voltage | DC 7-36V (6S LIPO) |
| Output Voltage | DC 5V (Max 500mA) |
| Video Input | CVBS PAL / NTSC |
| Audio Input | 6.5M MONO |
| Antenna Connector | MMCX 50Ω |
| External Control | Smart Audio |
| Dimensions (H*W*D) | 40mm * 24mm * 10.5mm |
| Weight | 15g (without cable) |
*MAX Power level can provide 2500mW (34dBm) or more power depending on the environment's ability to dissipate heat.
4. Package Contents
The RUSH MAX SOLO VTX package typically includes:
- RUSH MAX SOLO Image Transmission Unit x1
- Power Cable x2
- MMCX to SMA Adapter Cable x1
- Antenna x1

5. Setup and Installation
5.1. Wiring Diagram


5.2. SmartAudio Connection
- Connect the SmartAudio port of the VTX to a free UART-TX pad on your Flight Controller (FC).
- Open the BetaFlight configurator. Navigate to the Ports tab.
- Under the 'Peripherals' section, next to the UART connected to the VTX's RX pad, select TBS SmartAudio. The speed can typically be left at <auto>.
- Save the settings in BetaFlight.
6. Operating Instructions
6.1. Button Controls

- CHANNEL/BAND BUTTON: Press to set the channel. Press and hold to set the band.
- POWER BUTTON: Press to set the power level. Press and hold to toggle ON/OFF Pit Mode.
6.2. Power/Frequency Display
The chosen channel and band will be displayed in sequence. The number of flashes in red indicates the channel, and blue flashes for the band.
| LED Color | Power Level |
|---|---|
| GREEN | 25mW |
| BLUE | 500mW |
| RED | 1000mW |
| PURPLE | MAX |
- PIT Mode: Indicated by a flashing Power LED.
- EXIT PIT Mode: Press and HOLD the Power Button to select the desired Power Level.
- Overheated: The Power LED flashes rapidly, and the VTX slowly reduces transmit power. Once the VTX cools down, it will resume transmitting power, and the Power LED will stop flashing.
6.3. SmartAudio Control
The RUSH MAX SOLO VTX has a built-in SmartAudio Control Protocol. This allows VTX parameters to be quickly set via the OSD (On-Screen Display) or your radio control, after connecting to the Flight Controller (FC) or CRSF.
- Turn on your radio control. Set the Throttle (THR) to middle, Yaw to left, and Pitch to up to enter the OSD menu.
- In the OSD menu, navigate to Function > VTX SA to set the VTX working state.
- In the CONFIG menu:
- If set to RACE mode, the VTX will automatically enter PIT mode after booting.
- If set to FREE mode, the VTX will transmit normally after booting.
After switching the working mode, you may need to reconnect the power for the settings to take effect.
For more information on SmartAudio, please visit: https://github.com/betaflight/betaflight/wiki/Unify-Smartaudio
7. Maintenance
- Keep the VTX clean, especially the cooling fan and heatsink fins, to ensure optimal heat dissipation.
- Regularly inspect all cable connections and the antenna connector for any signs of wear or damage.
- Ensure the VTX is mounted in a location that allows for adequate airflow to prevent overheating, which can degrade performance and shorten lifespan.
- Avoid exposing the VTX to excessive moisture, dust, or extreme temperatures.
8. Troubleshooting
- No Video/Poor Signal:
- Ensure the antenna is securely connected to the VTX before powering on.
- Check all wiring connections for continuity and correct polarity.
- Verify the VTX is receiving the correct input voltage (DC 7-36V).
- Confirm the channel and band settings on the VTX match your FPV receiver.
- If using SmartAudio, ensure it is correctly configured in BetaFlight and the VTX is not stuck in Pit Mode.
- VTX Overheating:
- Check for obstructions around the cooling fan and heatsink.
- Ensure the VTX is mounted in a location with sufficient airflow.
- Reduce the power output if operating in a confined space or without adequate cooling.
- VTX Not Powering On:
- Verify the input voltage is within the specified range (DC 7-36V).
- Check power cable connections for shorts or disconnections.
- Damaged Antenna/Coaxial Cable:
- Replace any damaged antennas or coaxial cables immediately to prevent damage to the VTX's RF amplifier.
9. User Tips
- The built-in fan is crucial for maintaining high power output, especially at 2.5W, ensuring consistent performance and clean video.
- Always ensure proper airflow around the VTX when installing it in your drone frame to prevent overheating and maintain optimal performance.
- Always connect the antenna before powering on the VTX to prevent damage to the RF amplifier.
- The RUSH MAX SOLO is known for delivering clean video even in areas with moderate interference, making it suitable for long-range and freestyle FPV.
10. Warranty and Support
For warranty claims, technical support, or service inquiries, please contact your original point of purchase or the official RUSHFPV support channels. Keep your proof of purchase for any warranty-related requests.