JOYELEC LT-211

Contents

LT-211 Lever Wire Connector Instruction Manual

For Quick Connection 28-12 AWG (0.08-4mm²) 32A 250V

1. Introduction

The LT-211 Lever Wire Connector is designed for quick, safe, and reliable electrical connections. Made from flame-retardant materials, these compact splice terminals ensure a firm and insulated connection for a variety of cable sizes. They are ideal for organizing complex wiring in diverse applications, from residential to industrial settings.

Various LT-211 Lever Wire Connectors
Figure 1: Overview of LT-211 Lever Wire Connectors in different configurations.

2. Setup and Installation

The LT-211 connectors offer a fast and secure wiring solution, significantly reducing installation time compared to traditional methods. Follow these steps for proper installation:

  1. Prepare the Wire: Strip off approximately 10mm (0.39 inches) of the wire sheath. Ensure the exposed conductor is clean and free from damage.
  2. Open the Lever: Turn on the booster handle (lever) of the connector to open the wiring hole.
  3. Insert the Wire: Insert the stripped portion of the wire completely into the wiring hole. Ensure that no bare conductor is exposed outside the connector.
  4. Close the Lever: Press the booster handle down firmly to lock the wire in place. This completes the installation.
Step-by-step wiring instructions for LT-211 connectors with different wire types
Figure 2: Detailed wiring steps for single strand, multi-strand hard, and multi-strand cord wires.

The connector is compatible with various wire types and gauges:

  • Single Strand (BV): 0.08-4.0mm² (24AWG-12AWG)
  • Multi-strand Hard Wire (BVR): 0.08-4.0mm² (24AWG-12AWG)
  • Multi-strand Cord Wire (RV): 0.08-2.5mm² (24AWG-12AWG)
Labeled diagram of LT-211 connector components
Figure 3: Key components of the LT-211 connector, including booster handle, incoming/outgoing holes, measuring hole, and wire diameter indicator.

3. Operating Instructions

Once installed, the LT-211 connector provides a secure and insulated connection. The design allows for quick and efficient wiring, as highlighted by its '2 Seconds Wiring' capability.

LT-211 connector demonstrating '2 Seconds Wiring' and safety features
Figure 4: The LT-211 connector enables quick and safe connections, featuring flame retardant material and safety testing.

The integrated test hole allows for easy voltage testing without disconnecting the wires, enhancing safety and convenience during operation and troubleshooting.

4. Maintenance

The LT-211 connectors are designed for durability and require minimal maintenance. Periodically inspect connections for any signs of damage, corrosion, or loose wires. Ensure the levers are fully closed and the wires are securely held. The insulated material is robust, but avoid exposing the connectors to extreme physical stress or harsh chemicals.

5. Troubleshooting

The LT-211 connectors are designed to prevent common wiring hazards associated with traditional methods, such as exposed wires, loose connections, and potential for electrical leakage or fire.

Comparison of traditional wiring hazards versus LT-211 connector safety
Figure 5: Traditional wiring can pose hidden dangers like electrical leakage and cumbersome connections, which the LT-211 connector aims to eliminate.

If a connection is not working as expected:

  • Check Wire Stripping: Ensure the wire is stripped to the recommended 10mm length. Too little stripping may result in poor contact, while too much can expose the conductor.
  • Verify Wire Insertion: Confirm that the wire is fully inserted into the connector and that the stripped part is not exposed.
  • Secure Lever: Make sure the booster handle (lever) is fully pressed down and locked, securing the wire firmly.
  • Inspect for Damage: Check the connector and wire for any visible damage. Replace if necessary.

6. Specifications

AttributeValue
Product NameLT-211 Quick Terminal
Model NumberLT-211
Shell MaterialPA/PC Flame Retardant Nylon (Ignifugo PA66 material)
Wire Range0.08-4.0 mm² / 28-12 AWG
Applicable CablesFlexible/Hard Wire
Rated Current/Voltage32A / 250V / 4KV
Voltage (General)220 V
Stripping Length9-10 mm / 0.39 inches
Dimensions (L x W x H)39 x 8.5 x 15 mm
Conductive MaterialCopper Nickel Plating
Working Temperature-25~85℃
CertificationCE
Product dimensions and detailed specifications table for LT-211 connector
Figure 6: Visual representation of LT-211 dimensions and key specifications.

7. User Tips

  • Always ensure power is off before making any electrical connections.
  • Use the appropriate size connector for your wires to ensure a secure fit.
  • For multi-wire connections, ensure each wire is individually stripped and inserted correctly.
  • The compact design helps save space in junction boxes and electrical panels.

8. Warranty and Support

For any questions regarding the LT-211 Lever Wire Connectors, or for support, please contact the seller directly through the platform where the purchase was made. Please refer to your purchase details for specific warranty information provided by the seller.

© 2023 JOYELEC Store. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.