MAT-TUNER mAT-S1500

Contents

mAT-S1500 SWR & Power Meter User Manual

Model: mAT-S1500 | Brand: MAT-TUNER

Introduction

Thank you for purchasing the mAT-S1500 SWR & Power Meter. This manual provides essential information for the safe and effective use of your device. The mAT-S1500 is a digital standing wave meter and power meter designed for HF shortwave radio stations, operating within the 1.8-54MHz frequency range.

For detailed technical specifications, manuals, or software specific to your model, please contact the seller.

Safety Warnings

Before using this product, please read and comply with all safety instructions.

Electrical Safety

  • Use only the power adapter provided with the product or a compliant power supply.
  • Do not use in humid environments unless the product specifically states a waterproof rating.
  • If the power cord is damaged, discontinue use immediately and contact for replacement.
  • Always disconnect the power before cleaning.

Usage Environment

  • Operating temperature range: -10°C to 40°C (subject to model specifications).
  • Avoid direct sunlight, high temperatures, and dusty environments.
  • Ensure good ventilation and do not block heat dissipation holes.

Operational Safety

  • Do not disassemble or modify the product yourself; there are no user-repairable parts inside.
  • Prevent liquid from entering the product interior.
  • If the product emits smoke, unusual odors, or abnormal noise, immediately disconnect the power and contact after-sales service.

Setup and Basic Operations

Unpacking Inspection

After opening the package, please check that all items are complete. If any items are missing or damaged, contact us immediately.

First Use

Ensure the product is fully charged before use (if applicable). Check if the power supply voltage is consistent with the product specifications (AC100-240V, 50/60Hz, applicable worldwide).

The device features built-in two high-capacity 18650 lithium batteries, providing approximately 8 hours of battery life.

Device Overview

Front view of the mAT-S1500 SWR & Power Meter showing the 4.3-inch LCD display with FWD-15W and SWR readings.
Front view of the mAT-S1500 SWR & Power Meter.
Dimensions of the mAT-S1500 SWR & Power Meter: 140mm length, 95mm width, 80mm height.
Dimensions of the mAT-S1500 SWR & Power Meter.

Connections and Ports

Rear panel of the mAT-S1500 showing Power switch, Charge port (Type-C), Data port (DB9), RF IN, and RF OUT ports.
Rear panel connections: Power switch, Charge (Type-C), Data (DB9), RF IN, RF OUT.
Detailed view of RF IN and RF OUT ports. RF IN connects to the radio station, RF OUT connects to the antenna or false load.
RF IN and RF OUT port connections.
  • RF IN: Connects to the radio station.
  • RF OUT: Connects to the antenna or a false load.
  • CHARGE: Type-C charging port.
  • DATA: DB9 data interface (not used yet).
  • POWER: Power switch.

Basic Operations

  • Power On/Off: Press and hold the power button for 3 seconds to turn the device on or off.
  • Function Selection: Short press the mode button to switch functions.
  • Display Screen: The 4.3-inch high-resolution LCD screen uses a dual display design for numbers and progress bars. It automatically sets the background color of the screen according to ambient light, offering both daytime and night modes.
mAT-S1500 display in daytime mode and night mode, showing FWD-15W and SWR readings.
Daytime and Night Mode display examples.

Measurement Features

  • Automatic Range Switching: The 3-speed power range (15W, 150W, 1500W) automatically switches according to the input RF signal strength. The range scale displayed on the screen will also change accordingly.
  • High Precision Measurement: Designed with a radio frequency special measuring chip for good frequency consistency and accurate measurement of power and standing wave ratio.
  • Peak and Instantaneous Power Display: The device can display both peak power (MAX PEP) and instantaneous power.
  • High SWR Alarm: Progress bars show standing wave ratios in three colors: green (1.0-2.0), yellow (2.0-3.0), and red (3.0-10). If the measured SWR is higher than 3, the progress bar will turn red and an audible "Didi" alarm will sound.
Image illustrating automatic range switching for 15W, 150W, and 1500W power ranges.
Automatic power range switching.
Display showing peak power (MAX PEP) and instantaneous power readings.
Peak and Instantaneous Power display.
Display showing SWR alarm with color-coded bars: green for 1.0-2.0, yellow for 2.0-3.0, red for 3.0-10.
High SWR alarm indication.

Product Demonstration Video

Short video demonstrating the mAT-S1500 SWR & Power Meter in operation.

Specifications

Table of product parameters including Brand, Model, Frequency range, Power measurement range, Power accuracy, Interface, Standing wave ratio measurement range, Standing wave ratio accuracy, Impedance, Weight, Origin, Warranty Period.
Key product specifications.
ParameterValue
BrandMAT-TUNER (AISANRAY)
Model NumbermAT-S1500
TypeMini Amplifier (SWR & Power Meter)
Frequency Range1.8-54MHz
Power Measurement Range1-1500W
Power Accuracy+/-5% (7MHz)
InterfaceSO-239 (M mother)
Standing Wave Ratio Measurement Range1.00-9.99
Standing Wave Ratio Accuracy+/-3% (1.8-54MHz)
Impedance50Ω
Weight1.21kg
OriginMainland China
Input PowerAC100-240V, 50/60Hz or DC5V/9V/12V
Operating Temperature-10°C ~ 40°C
Storage Temperature-20°C ~ 60°C
Protection LevelIP20 (for indoor use, except for waterproof models)
CertificationNONE (Compliant with EU directives)
Built-in BatteryYes (two high-capacity 18650 lithium batteries, approx. 8 hours life)
Recommended Headphone Maximum Impedance< 32 Ohm (Note: This specification may be a generic category attribute and not directly applicable to this device's primary function.)
Output TypeLINE OUT (AUDIO OUT) (Note: This specification may be a generic category attribute and not directly applicable to this device's primary function.)
Input TypeLINE IN (AUDIO IN) (Note: This specification may be a generic category attribute and not directly applicable to this device's primary function.)

Note: Specifications are subject to change without prior notice. Please refer to the product label for the most accurate information.

Maintenance and Care

  • Cleaning: Wipe the outer casing with a soft, dry cloth. Do not use chemical solvents.
  • Storage: When not in use for an extended period, clean and store in a cool, dry place.
  • Battery (if applicable): If not used for an extended period, remove the battery to prevent leakage.

Troubleshooting Common Problems

ProblemPossible ReasonsSolution
Unable to power onPower not connected/battery depletedCheck the power connection, charge, and try again.
No display/Display errorPoor connection/Incorrect settingsRestart the device and check the connection.
Inaccurate measurement values (instrument-related)Range error/calibration requiredConfirm the measurement range and contact calibration services.
Other faults-Contact customer service for technical support.

User Tips

  • Charging Precaution: Do not measure while the device is charging, as this may damage the standing wave meter.
  • Range Switching: The power range can only be switched from a lower setting to a higher setting during use. To switch to a lower power range, you must restart the standing wave meter.
  • Frequency Range: The device is designed for 1.8-54MHz. If you require a wider frequency range (e.g., up to 500 MHz), please check for alternative models or contact the seller for specific product versions.

Warranty and Support

  • Warranty Policy: 12/24 months from the date of purchase (subject to store announcement).
  • Technical Support: For detailed technical documentation, calibration certificates, or hard copies of the manual, please contact us via AliExpress internal message or email: alisupport2026@163.com. Response time is typically within 24 working hours.

EU Compliance Information

CE Declaration of Conformity

This product complies with the essential requirements of the following EU directives:

  • Low Voltage Directive (LVD) 2014/35/EU
  • Electromagnetic Compatibility Directive (EMC) 2014/30/EU
  • RoHS Directive 2011/65/EU

Waste Electrical and Electronic Equipment (WEEE)

The wheeled bin symbol marked with an X on the product indicates that, according to EU Directive 2012/19/EU, this product must not be disposed of as unsorted municipal waste and must be collected and recycled separately.

Disclaimer

This instruction manual is a general version; the actual product functions and parameters shall prevail. The manufacturer reserves the right to change product designs and specifications without prior notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.