wofea ZC-S014

Contents

Wofea Wireless Shock Sensor Vibration Detector

Model: ZC-S014

Instruction Manual

Wofea wireless shock sensor, high sensitivity, 433MHz/1527

Image: Front view of the Wofea wireless shock sensor.

1. Introduction

The Wofea ZC-S014 is a wireless shock sensor and vibration detector designed to enhance the security of your premises. Operating at 433MHz, this high-sensitivity sensor detects vibrations caused by impacts, such as glass breaking or forced entry, and transmits an alarm signal to a compatible alarm system. It is an essential component for a comprehensive security setup, providing early detection of potential threats.

2. Setup and Installation

This sensor is designed for easy installation. Please ensure you have a compatible 433MHz alarm system or RF signal receiver before proceeding, as this sensor cannot operate independently.

2.1 Package Contents

  • Wireless Vibration Sensor (ZC-S014) x1
  • Double-sided adhesive tape (may be included)
  • Note: 12V 23A battery is NOT included and must be purchased separately.

2.2 Battery Installation

  1. Carefully open the sensor casing.
  2. Insert one 12V 23A battery into the designated battery compartment, ensuring correct polarity.
  3. Close the sensor casing securely.
Internal view of the Wofea ZC-S014 sensor showing the battery compartment for a 12V 23A battery.

Image: Internal view of the Wofea ZC-S014 sensor, highlighting the battery compartment.

2.3 Mounting the Sensor

  1. Identify the desired mounting location, such as a window pane, door frame, or wall, where vibrations are likely to occur during an intrusion attempt.
  2. Clean the surface thoroughly to ensure proper adhesion.
  3. Peel off the protective backing from the double-sided adhesive tape (if provided) and firmly attach it to the back of the sensor.
  4. Press the sensor firmly onto the chosen surface for at least 30 seconds.
Wofea wireless vibration sensor mounted on a window, illustrating its function to detect shock.

Image: Wofea wireless vibration sensor mounted on a window, demonstrating its shock detection capability.

2.4 Pairing with Alarm System

Refer to your alarm system's instruction manual for specific pairing procedures. Generally, the process involves:

  1. Putting your alarm system into "learning" or "pairing" mode.
  2. Triggering the vibration sensor (e.g., by gently tapping the surface it's mounted on) to send a signal to the alarm panel.
  3. Confirming successful pairing on your alarm system's display or indicator.
Diagram showing the Wofea wireless vibration sensor wirelessly connected to various 433MHz alarm panels and a siren.

Image: Diagram illustrating the wireless connection of the vibration sensor to various compatible 433MHz alarm systems.

3. Operation

Once installed and paired with your alarm system, the Wofea ZC-S014 sensor operates automatically.

  • Detection: The sensor continuously monitors for vibrations. When it detects a significant shock or vibration (e.g., from glass breaking, a door being forced open, or an object hitting the protected surface), it will trigger.
  • Signal Transmission: Upon detection, the sensor immediately sends a wireless alarm signal (433MHz) to your connected alarm control panel.
  • Alarm Activation: Your alarm control panel will then process this signal according to its programming, typically activating sirens, sending notifications (if it has GSM/WiFi capabilities), or triggering other connected security devices.
Wofea wireless vibration sensor detecting vibrations on a window, with shattered glass in the background.

Image: The sensor actively detecting vibrations on a window, indicating its primary function.

4. Maintenance

4.1 Battery Replacement

The sensor is powered by a 12V 23A battery. When the battery level is low, your alarm system may indicate a low battery warning for the sensor. To replace the battery:

  1. Carefully open the sensor casing.
  2. Remove the old 12V 23A battery.
  3. Insert a new 12V 23A battery, observing correct polarity.
  4. Close the sensor casing securely.
  5. Test the sensor to ensure it is functioning correctly and communicating with your alarm system.

4.2 Cleaning

Wipe the sensor periodically with a soft, dry cloth to remove dust and debris. Do not use liquid cleaners or abrasive materials, as these can damage the device.

5. Troubleshooting

ProblemPossible CauseSolution
Sensor not triggering alarm.
  • Low or dead battery.
  • Sensor not properly paired with the alarm system.
  • Sensor mounted on an unstable surface.
  • Alarm system not armed.
  • Replace the 12V 23A battery.
  • Re-pair the sensor with your alarm system (refer to Section 2.4).
  • Relocate the sensor to a more stable surface.
  • Ensure your alarm system is armed.
False alarms.
  • Sensor sensitivity too high.
  • Sensor mounted near a source of minor vibrations (e.g., air vent, loose object).
  • Check if your alarm system allows for sensitivity adjustment for the sensor.
  • Relocate the sensor away from sources of unwanted vibrations.
Poor wireless range.
  • Obstructions between sensor and alarm panel.
  • Interference from other wireless devices.
  • Ensure clear line of sight or minimal obstructions between the sensor and the alarm panel.
  • Move the sensor or alarm panel to reduce interference.

6. Specifications

FeatureDetail
Model NumberZC-S014
Brand Namewofea
Wireless Frequency433MHz
IC Type1527 (with 330K resistor)
Power Supply1 x 12V 23A battery (not included)
Static Current≤18uA
Transmission Current≤16.5mA
Transmission DistanceUp to 100m in open air (approx. 80m without obstacle)
Operating Temperature-10°C to 40°C (14°F to 104°F)
Operating Humidity≤90%
Detection MethodVibration/Shock
ColorWhite
Dimensions (approx.)Length: 8cm, Width: 5cm, Height: 1cm
Weight (approx.)0.028 kg

7. User Tips

  • Compatibility Check: Always confirm that your existing alarm system operates on the 433MHz frequency and supports 1527 IC type sensors before purchasing. For example, this sensor is known to work with Kerui W181 433MHz alarm systems.
  • Optimal Placement: For best performance, mount the sensor directly on the surface you wish to protect (e.g., window glass, door panel). Avoid mounting on surfaces that experience frequent, non-threatening vibrations.
  • Battery Life: To maximize battery life, ensure the sensor is not placed in areas with extreme temperature fluctuations. Replace the battery promptly when a low battery warning is indicated by your alarm system.

8. Warranty and Support

For warranty information and technical support, please refer to the documentation provided by your retailer or contact Wofea customer service directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.