HGLRC SPECTER F460 Stack

Contents

HGLRC SPECTER F460 Stack Instruction Manual

Model: SPECTER F460 Stack

1. Introduction

The HGLRC SPECTER F460 Stack is a high-performance flight control system designed for FPV freestyle drones. It integrates the SPECTER F405 V2 Flight Controller and the SPECTER 60A 4in1 Electronic Speed Controller (ESC) into a compact and efficient unit. This manual provides essential information for the proper setup, operation, and maintenance of your SPECTER F460 Stack.

2. Key Features

  • Flight Controller (FC): Utilizes the stable MPU6000 gyroscope and F405 main control chip for fast operation and smooth control.
  • ESC: Features a new imported FD6288 processor paired with ON3109 high-performance MOS for continuous current handling and stable output.
  • Connectivity: Designed for quick, solder-free connections to camera, receiver, image transmission, LED, and GPS units via dedicated sockets.
  • Power Output: Supports BEC 9V2A and BEC 5V2.5A, providing stable voltage and current for external devices.
  • Durability: Immersion gold high-tech design ensures temperature and current resistance, with large pads on the ESC for robust connections.
  • Data Logging: Integrated 16MB black box for recording flight data.
  • Current Monitoring: Onboard galvanometer module allows real-time viewing of current feedback.

3. Specifications

3.1. HGLRC SPECTER F460 Stack

ParameterValue
Input Voltage2-6S Lipo (7.4V-22.8V)
Installing Hole30.5x30.5mm, M3
Support ProtocolsDShot600/300/150/Oneshot125/42, MultiShot
Weight29g

3.2. SPECTER F405 FC

ParameterValue
MCUSTM32F405
GYROMPU6000
OSDAT7456E
Blackbox16MB
UART4
BEC9V2A/5V2.5A
FC FirmwareHGLRCF405V2
Size38mm*38mm

3.3. SPECTER 60A ESC

ParameterValue
Constant Current60A
Peak Current70A (10s)
ESC FirmwareBL_S (J-H-30)
Size37x42.7mm

4. Setup and Installation

IMPORTANT: Before soldering, connect the stack to Betaflight (BF) to ensure all sensor functions are normal. Contact customer service immediately if any issues arise.

4.1. Physical Installation

The HGLRC SPECTER F460 Stack is designed for a 30.5x30.5mm mounting pattern with M3 screws. Ensure proper alignment and secure fastening within your drone frame.

Schematic diagram showing front and back views with dimensions for SPECTER F405 and SPECTER 60A
Figure 1: Schematic diagram of front and back views of SPECTER F405 and SPECTER 60A, including dimensions.

4.2. Wiring Connections

The SPECTER F460 Stack supports plug-and-play connections for various peripherals, minimizing the need for soldering. Refer to the detailed wiring diagram below for connecting your camera, receiver, image transmission, LED, and GPS modules.

Detailed wiring diagram for HGLRC SPECTER F460 Stack, showing connections for camera, receiver, video transmitter, GPS, and LED
Figure 2: Detailed wiring diagram for the HGLRC SPECTER F460 Stack.
Diagram illustrating plug-and-play connections for camera, receiver, image transmission, LED, and GPS on the flight controller
Figure 3: Plug-and-play connections for various peripherals.

The flight controller features dedicated ports for:

  • Camera
  • SBUS Receiver
  • Analog Video Transmission
  • LED/Buzzer
  • GPS
  • CRSF Receiver

4.3. Firmware and Configuration

The Flight Controller uses HGLRCF405V2 firmware, and the ESC uses BL_S (J-H-30) firmware. Connect the FC to your computer via USB and use Betaflight Configurator for initial setup, calibration, and parameter adjustments. Ensure you have the latest Betaflight Configurator installed.

5. Operating Instructions

5.1. Pre-Flight Checks

  • Verify all connections are secure and correctly wired.
  • Ensure propellers are correctly mounted and tightened.
  • Check battery voltage and ensure it is within the 2-6S Lipo range.
  • Confirm flight controller and ESC settings in Betaflight.

5.2. Flight Data Recording

The integrated 16MB black box automatically records flight data. This data can be downloaded via Betaflight Configurator for analysis and tuning, which is crucial for optimizing flight performance and troubleshooting issues.

5.3. Real-time Monitoring

The onboard galvanometer module provides real-time current feedback, which can be viewed through your OSD (On-Screen Display) or Betaflight. This helps monitor power consumption and battery health during flight.

Diagram highlighting key features of the SPECTER F405 Flight Controller, including MPU6000 gyroscope, STM32F405, 8M black box, barometer, and BEC
Figure 4: SPECTER F405 Flight Controller Function Display.
Diagram highlighting key features of the SPECTER 60A ESC, including Bluejay/96K firmware support, oversized pads, high-end MOS tubes, and onboard ammeter
Figure 5: SPECTER 60A ESC Function Display.

6. Maintenance

  • Regularly inspect all solder joints and connections for any signs of damage or looseness.
  • Keep the stack clean and free from dust, dirt, and moisture. Use compressed air or a soft brush for cleaning.
  • Check for any physical damage to the boards or components after crashes.
  • Ensure adequate airflow around the stack during operation to prevent overheating, especially for the ESC.
  • Periodically check for firmware updates for both the FC (Betaflight) and ESC (BLHeli_S or Bluejay/96K) to benefit from performance improvements and bug fixes.

7. Troubleshooting

7.1. Initial Power-Up Issues

  • No power/lights: Double-check battery connection polarity and ensure the battery is charged. Inspect for any short circuits.
  • Smoke/Burning smell: Immediately disconnect power. This indicates a short circuit or incorrect wiring. Carefully inspect all connections, especially power leads, for reversed polarity or bridging.

7.2. Flight Controller Not Connecting to Betaflight

  • Ensure correct USB cable is used (data cable, not just charging).
  • Install necessary VCP (Virtual COM Port) drivers for STM32 microcontrollers.
  • Try a different USB port or computer.
  • If in DFU mode, use the Betaflight 'Flash Firmware' tab to re-flash the FC firmware.

7.3. Motor Issues (No spin, erratic spin)

  • Verify motor connections to the ESC are correct.
  • Check ESC calibration in Betaflight.
  • Ensure ESC firmware (BL_S) is correctly flashed and configured.
  • Inspect motors for physical damage or debris.

7.4. Sensor Malfunctions

If sensors (gyro, accelerometer, barometer) are not functioning correctly, ensure the FC is properly mounted and free from vibrations. Re-calibrate sensors in Betaflight. If issues persist, re-flash the FC firmware.

8. User Tips

  • Always perform a dry run (without propellers) after any changes to wiring or settings to ensure motors spin correctly and in the right direction.
  • Utilize the black box data to fine-tune your PID settings for optimal flight performance.
  • Keep your firmware updated to benefit from the latest features and stability improvements.
  • When connecting peripherals, double-check the voltage requirements to avoid damaging components. The BEC provides 9V and 5V outputs.

9. Warranty and Support

For technical support, warranty claims, or any questions regarding your HGLRC SPECTER F460 Stack, please contact the seller or manufacturer directly. Retain your proof of purchase for warranty purposes.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.