FLIPSKY 75100 V2.0

Contents

Flipsky 75100 V2.0 Electronic Speed Controller User Manual

Model: FSECS75100 V2.0

1. Introduction

The Flipsky 75100 V2.0 Electronic Speed Controller (ESC) is based on the VESC 75 series, offering advanced control for electric skateboards, scooters, and e-bikes. It is programmable via VESC_Tool 3.0 (firmware 5.2) and features overheat and overcurrent protection, as well as regenerative braking capabilities. Designed with an aluminum case for efficient heat dissipation, this ESC supports a maximum working voltage of 20S (84V). The 75100 V2.0 also includes single serial port functionality and integrates a power on/off switch or key switch for convenient operation.

Flipsky 75100 V2.0 ESC with integrated power button and various connectors.

Figure 1: Flipsky 75100 V2.0 ESC with integrated power button.

Flipsky 75100 V2.0 ESC with integrated key switch and various connectors.

Figure 2: Flipsky 75100 V2.0 ESC with integrated key switch.

2. Specifications

Dimensions of the Flipsky FSECS75100 V2.0 ESC: 103mm length, 58mm width, 18.5mm height.

Figure 3: Physical dimensions of the FSECS75100 V2.0 ESC.

FeatureDescription
Size103mm x 58mm x 24mm
Voltage Range14-84V (4-20S)
Continuous Current100A
Peak Current250A
Firmware5.02 (firmware upgrade available)
BEC Output5V@1A
Operating ModesDC, BLDC, FOC (sinusoidal)
Control Interface PortsUSB, CAN, UART
Supported SensorsABI, HALL, AS5047, AS5048A
Input Set SupportPPM, ADC, NRF, UART
Wire Size12AWG
ProgrammableYes
Regenerative CapacityYes
OriginMainland China
TypeController
Internal view of the Flipsky FSECS75100 V2.0 PCB with capacitors and main chip.

Figure 4: Internal PCB view of the FSECS75100 V2.0.

3. Setup and Wiring

Careful wiring is crucial for the proper function and safety of your ESC. Refer to the diagrams below for correct connections.

3.1 Main Wiring Diagram

Wiring diagram for Flipsky FSECS75100 V2.0 ESC showing connections for motor, battery, USB, PPM, CAN+POWER, 4.SWD, COMM, UART2, HALL, and POWER SWITCH.

Figure 5: Main wiring diagram for FSECS75100 V2.0.

This diagram illustrates the connection points for the motor, battery, and various control interfaces. Key connections are labeled:

  1. USB Port
  2. PPM (Pulse Position Modulation)
  3. CAN+POWER
  4. 4.SWD (Serial Wire Debug)
  5. COMM (Communication)
  6. UART2 (Universal Asynchronous Receiver-Transmitter)
  7. HALL Sensor Port
  8. POWER SWITCH Port

Note the blue and red/green LEDs for status indication. Always press to unplug connectors; do not pull directly on wires to avoid damage to the wires or connectors.

3.2 Multi-ESC (2WD) Setup

When building a 2WD system or using multiple ESCs, connect them via CAN-BUS wires. Ensure the following correct wiring between the master and slave ESCs:

  • Master board GND to Slave board GND
  • Master CANL to Slave CANL
  • Master CANH to Slave CANH
  • Master 5V to Slave PWR ON
Diagram showing how to connect master and slave ESCs via CAN-BUS wires.

Figure 6: Master/Slave ESC CAN-BUS wiring diagram.

Two Flipsky FSECS75100 V2.0 ESCs connected, one with a power button and the other with a key switch, illustrating a multi-ESC setup.

Figure 7: Example of two FSECS75100 V2.0 ESCs in a multi-ESC setup.

4. Operating Instructions

The Flipsky 75100 V2.0 ESC is programmable using the VESC_Tool 3.0 software. This tool allows for configuration of motor parameters, input settings, and various control modes (DC, BLDC, FOC).

4.1 Power On/Off

The ESC integrates either a power on/off button or a key switch, depending on your specific model. Use this switch to safely power the unit on and off. Ensure all connections are secure before powering on.

4.2 Firmware Configuration

Connect the ESC to your computer via the USB port and use VESC_Tool 3.0 for initial setup and parameter adjustments. Refer to the VESC_Tool documentation for detailed instructions on motor detection, input configuration (PPM, ADC, NRF, UART), and mode selection.

5. Maintenance

To ensure the longevity and optimal performance of your Flipsky 75100 V2.0 ESC, follow these maintenance guidelines:

  • Keep Clean: Regularly inspect the ESC for dust, dirt, or debris. Clean gently with a soft, dry brush or compressed air.
  • Avoid Moisture: While the aluminum case provides some protection, avoid exposing the ESC to water or excessive moisture to prevent internal damage.
  • Connection Integrity: Periodically check all wire connections for looseness or corrosion. Secure any loose connections.
  • Firmware Updates: Keep your ESC firmware updated to the latest stable version. When upgrading to firmware 5.03 or newer, it is critical to turn off the phase filter in the VESC_Tool settings to prevent issues.

6. Troubleshooting

If you encounter issues with your ESC, consider the following common problems and solutions:

  • ESC Not Powering On: Check battery connections, power switch functionality, and ensure the battery is charged.
  • Motor Not Responding: Verify motor phase wire connections and sensor wire connections (if applicable). Perform motor detection in VESC_Tool.
  • Overheat Protection Triggered: Ensure adequate airflow around the ESC. Reduce load or check for short circuits in the motor or wiring.
  • Overcurrent Protection Triggered: This indicates excessive current draw. Check for motor issues, incorrect motor parameters in VESC_Tool, or short circuits.
  • Battery Compatibility Issues: While the ESC supports 4-20S (14-84V), some users have reported compatibility issues with specific 18S and 20S 72V nominal battery configurations. If experiencing problems, verify your battery's actual voltage and discharge capabilities against the ESC's specifications and consider consulting the manufacturer or community forums for known incompatibilities.
  • Sparking During Battery Connection: The integrated power button or key switch may not fully eliminate sparks when connecting high-voltage batteries. It is recommended to use an anti-spark connector or take appropriate precautions during battery connection to minimize sparking and potential damage to connectors.

7. User Tips

  • Always ensure correct wiring, especially for multi-ESC setups, to prevent damage and ensure synchronized operation.
  • When upgrading firmware to VESC_Tool 5.03 or newer, remember to turn off the phase filter in the software settings.
  • Be aware of potential battery compatibility issues; some users have reported issues with 18S and 20S 72V nominal batteries despite the stated 4-20S range. Verify compatibility with your specific battery setup.
  • Consider using an anti-spark connector or taking precautions when connecting the battery, as the integrated power button may not fully prevent sparks.

8. Safety Information

⚠️️ WARNING: Please mind potential fire risk and strictly follow the instruction manual for charging and storage of batteries connected to this device.

This ESC is a high-power electronic device. Improper use or installation can lead to serious injury or damage. Always observe the following safety precautions:

  • Electrical Safety: Always disconnect the battery before performing any wiring or maintenance. Avoid touching exposed wires or components when the system is powered.
  • Voltage Limits: Do not exceed the maximum voltage rating of 84V (20S). Over-voltage can permanently damage the ESC.
  • Current Limits: Do not exceed the continuous or peak current ratings. Excessive current can lead to overheating and failure.
  • Heat Management: Ensure the ESC has adequate ventilation. The aluminum case aids in heat dissipation, but prolonged high-current operation in enclosed spaces can still lead to overheating.
  • Component Integrity: Do not use the ESC if any components appear damaged or if the casing is compromised.

9. Warranty and Support

For technical support, troubleshooting assistance, or warranty inquiries regarding your Flipsky 75100 V2.0 ESC, please contact the FLIPSKY Official Store directly. Provide your product model and a detailed description of the issue to facilitate prompt support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.