1. Product Overview
The YAXUN YX889A is a versatile 3-in-1 combination rework station designed for mobile phone repair and other electronic component work. It integrates a hot air station, a soldering iron, and an LCD touch separator into a single compact unit. This manual provides instructions for safe and efficient operation.
2. Safety Precautions
- Always operate the unit in a well-ventilated area.
- Wear appropriate personal protective equipment (PPE), such as safety glasses and heat-resistant gloves.
- Do not touch hot surfaces or components. Allow them to cool before handling.
- Ensure the power supply matches the unit's voltage requirements (110V or 220V).
- Keep flammable materials away from the work area.
- Unplug the unit from the power source before cleaning or maintenance.
- This device is ESD Safe. Take appropriate anti-static measures when working with sensitive electronic components.
3. Package Contents
Verify that all items are present in the package:
- YAXUN YX889A Main Unit (Hot Air Station, Soldering Station, LCD Separator)
- Hot Air Handle
- Soldering Handle
- Soldering Iron Stand with Sponge
- Hot Air Nozzles (various sizes)
- Power Cord
4. Setup Instructions
- **Unpacking**: Carefully remove all components from the packaging.
- **Placement**: Place the main unit on a stable, heat-resistant, and level surface. Ensure adequate ventilation around the unit.
- **Connect Hot Air Handle**: Connect the hot air handle to the designated port on the main unit.
- **Connect Soldering Handle**: Connect the soldering handle to the designated port on the main unit.
- **Soldering Iron Stand**: Place the soldering iron stand in a convenient location and moisten the cleaning sponge with water.
- **Power Connection**:
- Verify the voltage switch on the back of the unit matches your local power supply (110V or 220V).
- Connect the power cord to the main unit's power input.
- Plug the power cord into a grounded electrical outlet.
5. Operating Instructions
5.1 General Operation
- **Power On**: Flip the main POWER switch on the front panel to the "ON" position. The digital displays will illuminate.
- **Temperature Memory Function**: The unit features a temperature memory function for both the hot air and soldering iron. Press the temperature setting button (labeled "SET" or similar) to cycle through P0, P1, P2, P3. Adjust the temperature using the corresponding knobs. The unit will save the set temperature for each preset, eliminating the need to re-adjust every time.
5.2 Hot Air Station
- **Power On Hot Air**: Flip the "SMD REWORK" switch to "ON".
- **Set Temperature**: Use the "TEMP °C" knob for the hot air station to set the desired temperature. The digital display will show the current and set temperatures.
- **Adjust Airflow**: Use the "AIR" knob to adjust the airflow intensity. Start with a lower setting and increase as needed.
- **Operation**: When you pick up the hot air handle from its holder, the heating element will activate, and air will begin to flow.
- **Automatic Stoppage**: When the hot air handle is returned to its holder, the machine will automatically initiate a cool-down process by blowing cool air until the temperature drops to a safe level, then it will enter standby mode. This extends the life of the heating element.
- **Applications**: Suitable for unsoldering various components such as SOIC, CHIP, QFP, PLCC, and BGA, especially for flat cables and cable connectors. Also applicable for hot contraction, heating, depainting, degluing, defrosting, preheating, and rubber soldering.
5.3 Soldering Iron
- **Power On Soldering Iron**: Flip the "SOLDERING" switch to "ON".
- **Set Temperature**: Use the "TEMP °C" knob for the soldering iron to set the desired temperature. The digital display will show the current and set temperatures.
- **Pre-tinning**: Before first use, or after cleaning, pre-tin the soldering iron tip with solder to prevent oxidation.
- **Soldering**: Apply the soldering iron tip to the component and solder joint, then feed solder to the joint.
- **Cleaning**: Regularly clean the soldering iron tip using the wet sponge in the stand to remove excess solder and flux residue.
5.4 LCD Touch Separator
- **Power On LCD Separator**: Ensure the main power is on.
- **Activate Vacuum Pump**: Press the red "Pump" button to activate the vacuum suction.
- **Place Device**: Carefully place the mobile phone or LCD assembly onto the heating plate. The vacuum will hold it in place.
- **Set Temperature**: Use the "ENT" temperature control for the LCD Disassembly Machine to set the desired heating temperature for screen separation.
- **Separation**: Once the plate reaches the desired temperature, use appropriate tools (e.g., thin metal sheets, plastic cards) to carefully separate the LCD from the frame or glass.
- **Deactivate Vacuum**: Press the red "Pump" button again to release the vacuum.
Video 1: Demonstration of LCD separator vacuum function and temperature setting for the hot air gun.
6. Maintenance
- **Cleaning**: Regularly clean the unit's exterior with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
- **Soldering Tip Care**: Keep the soldering iron tip clean and tinned. Replace worn or oxidized tips to ensure optimal performance.
- **Hot Air Nozzles**: Ensure hot air nozzles are free from debris.
- **Air Filter (if applicable)**: Check and clean any air filters if present to maintain proper airflow.
- **Storage**: Store the unit in a dry, dust-free environment when not in use.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit does not power on. | No power supply; power switch off; faulty power cord. | Check power connection; ensure power switch is ON; test power cord. |
| Hot air gun not heating or low airflow. | Temperature/airflow set too low; handle not in active position; heating element fault. | Adjust temperature/airflow knobs; ensure handle is picked up; contact support if issue persists. |
| Soldering iron not heating. | Temperature set too low; faulty heating element/tip. | Adjust temperature knob; replace soldering tip; contact support if issue persists. |
| LCD separator vacuum not working. | Pump button not pressed; leaks in vacuum system; faulty pump. | Press the red "Pump" button; check for proper sealing of the device on the plate; contact support. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | YX-889A |
| Brand | YAXUN |
| Origin | Mainland China |
| Certification | CE |
| Function | Hot Air, Soldering, LCD Separator (3-in-1 Combination Rework Station) |
| Application | Mobile phone repair, unsoldering components (SOIC, CHIP, QFP, PLCC, BGA), hot contraction, heating, depainting, degluing, defrosting, preheating, rubber soldering. |
| Voltage | 110V / 220V (selectable) |
| Power | 780W |
| Frequency | 50/60Hz |
| Current | 8A |
| Dimensions (L x W x H) | Approx. 30cm x 17cm x 17cm |
| Package Weight | 5.9 kg |
| Package Dimensions (L x W x H) | 43cm x 25cm x 23cm |
9. User Tips
- **Temperature Presets**: Utilize the P0, P1, P2, P3 memory functions for frequently used hot air and soldering iron temperatures to save time during operation.
- **Voltage Check**: Always double-check the voltage switch on the back of the unit (110V/220V) before plugging it in to prevent damage.
- **Hot Air Nozzles**: Experiment with different hot air nozzles for various component sizes to achieve precise heating and prevent damage to surrounding parts.
- **LCD Separation**: For stubborn LCDs, ensure the heating plate has reached a stable temperature and allow sufficient time for the adhesive to soften before attempting separation.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.