Sunshine SS-818

Contents

Sunshine SS-818 UV Glue Curing Lamp

Model: SS-818

User Instruction Manual

1. Introduction

The Sunshine SS-818 UV Glue Curing Lamp is a specialized LED UV device designed for mobile phone repair and green oil curing applications. Featuring a 36W power output and a four-tube design with 180-degree irradiation, it ensures fast and efficient curing without leaving dead angles. This manual provides essential information for the safe and effective use of your UV curing lamp.

2. Safety Information

  • **UV Radiation:** Avoid direct exposure of eyes and skin to UV light. Use appropriate protective eyewear and gloves during operation.
  • **Electrical Safety:** Ensure the device is connected to a power source matching the specified voltage (220-240V). Do not operate with wet hands or in damp environments.
  • **Ventilation:** Use in a well-ventilated area to dissipate any fumes from curing materials.
  • **Placement:** Place the lamp on a stable, flat, and heat-resistant surface. Keep away from flammable materials.
  • **Children:** Keep out of reach of children.
  • **Damage:** Do not use if the power cord or device is damaged. Contact support for repairs.

3. Package Contents

Please check the package for the following items:

  • Sunshine SS-818 UV Glue Curing Lamp
  • Power Cable
  • User Manual (this document)

4. Product Overview

Familiarize yourself with the components and controls of your SS-818 UV Curing Lamp.

Sunshine SS-818 UV Glue Curing Lamp front view

Figure 4.1: Front view of the Sunshine SS-818 UV Glue Curing Lamp.

Dimensions of the UV Curing Lamp

Figure 4.2: Dimensions of the UV Curing Lamp (Length: 240mm, Width: 200mm, Height: 95mm).

Work area dimensions of the UV Curing Lamp

Figure 4.3: Work area dimensions (approximately 14.8cm x 13.9cm).

Control buttons for the UV Curing Lamp

Figure 4.4: Control Buttons. The Red button activates the 120-second timer. The Black button is a 3-position switch: '0' for off, '1' for continuous light mode, and '2' for timing mode.

Diagram showing 180-degree irradiation from four UV tubes

Figure 4.5: 180-degree irradiation from four tubes for comprehensive curing.

5. Specifications

Feature Specification
Model SS-818
Power 36W
Voltage 220-240V, 50/60Hz
Material Plastic
Type Combination (UV Glue Curing Lamp)
Irradiation Angle 180 degrees (four-tube)
Dimensions (L x W x H) 240mm x 200mm x 95mm
Work Area (approx.) 14.8cm x 13.9cm
Weight 0.65 kg

6. Setup

  1. **Unpack:** Carefully remove the UV curing lamp and all accessories from the packaging.
  2. **Placement:** Place the lamp on a stable, level, and dry surface. Ensure there is adequate space around the device for ventilation.
  3. **Power Connection:** Connect the power cable to the lamp's power input port, then plug the other end into a compatible 220-240V AC power outlet.
  4. **Inspection:** Before first use, inspect the lamp for any visible damage.

7. Operating Instructions

The SS-818 UV Curing Lamp offers two operating modes: Continuous Light Mode and Timing Mode.

7.1 Continuous Light Mode

  1. Ensure the lamp is properly connected to power.
  2. Flip the Black button switch to the '1' position. The UV tubes will illuminate continuously.
  3. Place the item to be cured within the work area of the lamp.
  4. Once curing is complete, flip the Black button switch to the '0' position to turn off the lamp.

7.2 Timing Mode (120 Seconds)

  1. Ensure the lamp is properly connected to power.
  2. Flip the Black button switch to the '2' position (Timing Mode).
  3. Place the item to be cured within the work area of the lamp.
  4. Press the Red button. The UV tubes will illuminate and operate for 120 seconds, then automatically turn off.
  5. If you need to stop the curing process before 120 seconds, flip the Black button switch to the '0' position.

Note:

  • Always wear UV protective eyewear when operating the lamp.
  • Curing times may vary depending on the type and thickness of the UV glue or green oil.

8. Maintenance

  • **Cleaning:** Disconnect the power before cleaning. Use a soft, dry cloth to wipe the exterior of the lamp. Do not use abrasive cleaners or solvents.
  • **Storage:** When not in use, store the lamp in a cool, dry place, away from direct sunlight and moisture.
  • **Bulb Replacement:** The UV tubes are designed for long life. If a tube needs replacement, contact the seller or a qualified technician.

9. Troubleshooting

Problem Possible Cause Solution
Lamp does not turn on No power, loose connection, faulty switch/bulb Check power outlet and cable connection. Ensure Black switch is not in '0' position. If problem persists, contact support.
Glue/Oil not curing properly Insufficient curing time, incorrect material, faulty UV tube Increase curing time. Ensure the material is UV-curable. Check if all UV tubes are illuminating.
Lamp overheats Poor ventilation, prolonged use Ensure adequate ventilation. Allow the lamp to cool down between prolonged uses.

10. User Tips

  • **Handle with Care:** Some users have noted sharp edges on the product. Exercise caution when handling the lamp, especially during unpacking and setup.
  • **Material Compatibility:** Always verify that your specific glue, resin, or green oil is compatible with UV curing and the wavelength emitted by this lamp for optimal results.
  • **Voltage Check:** Double-check the voltage requirements on the product label to ensure it matches your local power supply before plugging in.

11. Frequently Asked Questions (FAQ)

Q: What is the voltage of this lamp?
A: The Sunshine SS-818 UV Glue Curing Lamp operates on 220-240V, 50/60Hz. Please check the label on your specific unit for confirmation.
Q: Can I use this lamp with 110V?
A: No, this model is specified for 220-240V. Using it with a 110V power supply without a proper voltage converter may damage the device or prevent it from functioning correctly. Always match the device's voltage requirements with your power supply.
Q: Is this lamp suitable for curing polymer stamps?
A: This lamp is primarily designed for UV glue and green oil curing in mobile phone repair. While UV light is used in polymer stamp making, compatibility depends on the specific polymer material and its required UV wavelength and intensity. Please consult the manufacturer's guidelines for your polymer material.

12. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or retailer from whom you purchased the product. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.