1. Introduction
The XY-S100H is a versatile 2.1-channel Bluetooth audio power amplifier module designed for high-fidelity sound reproduction. It features independent high and low tone controls for the main stereo channels and a dedicated output for a subwoofer, allowing for a customized audio experience. This module is ideal for DIY audio projects, home theater systems, and upgrading existing sound setups.
2. Key Features
- 2.1-Channel Audio Output: Provides stereo (Left/Right) and a dedicated subwoofer channel.
- Bluetooth Connectivity: Seamless wireless audio streaming from compatible devices.
- High and Low Tone Control: Adjustable treble and bass for main channels.
- Dedicated Subwoofer Output: Independent volume control for the subwoofer.
- High Power Output: Delivers up to 100 Watts RMS power into a 4-ohm load with low distortion (<1% THD+N).
- Wide Operating Voltage Range: Compatible with 12-26V DC power supplies.
- Built-in Protection: Includes safeguards against over-voltage, under-voltage, over-current, and short-circuits for enhanced durability and safety.
3. Specifications
| Feature | Specification |
|---|---|
| Model | XY-S100H |
| Type | Audio Power Amplifier Module |
| Channels | 2.1 (Left, Right, Subwoofer) |
| Power Output | Up to 100W RMS (into 4Ω load, <1% THD+N) |
| Operating Voltage | 12-26V DC |
| Protection Features | Over-voltage, Under-voltage, Over-current, Short-circuit |
| Dimensions (L x W x H) | Approx. 13 cm x 11 cm x 8 cm |
| Weight | Approx. 0.241 kg |
4. Package Contents
The package typically includes:
- 1 x XY-S100H 2.1-Channel Bluetooth Audio Power Amplifier Board Module
- Control knobs (pre-installed or separate)
- Other necessary components (e.g., standoffs, small connectors) if included by the manufacturer.
5. Setup Instructions
Before connecting, ensure all components are powered off. Handle the module with care to avoid static discharge.
- Identify Components: Familiarize yourself with the module's layout.
- Connect Power Supply: Connect a 12-26V DC power supply to the DC-IN terminals on the board. Ensure correct polarity (+ to +, - to -). A power supply with sufficient current capacity (e.g., 5A or higher) is recommended for optimal performance, especially at higher volumes.
- Connect Speakers:
- Connect your passive stereo speakers to the L/R OUT terminals. Ensure correct polarity for each speaker.
- Connect your passive subwoofer to the SUB OUT terminal. Ensure correct polarity.
- The amplifier is designed to deliver up to 100W RMS into a 4-ohm load. Ensure your speakers and subwoofer are compatible with this power output and impedance.
- Connect Audio Input:
- Bluetooth: Once the module is powered on, it will enter Bluetooth pairing mode.
- AUX Input: Alternatively, connect an audio source (e.g., smartphone, PC, MP3 player) to the AUX input using a 3.5mm audio cable.
- Initial Power On: After all connections are secure, turn on the DC power supply. The module should power on, and a status indicator (if present) may light up.



Video 1: Demonstration of XY-S100H Amplifier Board Features. This video showcases the physical aspects of the amplifier board, its power output capabilities, and built-in protection mechanisms. It also provides a visual guide to the various connection points and control knobs.
6. Operation
- Bluetooth Pairing:
- Power on the XY-S100H module.
- On your audio source device (e.g., smartphone, tablet), go to Bluetooth settings.
- Search for available devices and select "XY-S100H" to pair. A confirmation sound may be heard from the speakers once paired.
- Audio Playback:
- Start playing audio from your connected Bluetooth device or AUX source.
- Adjust the master volume knob on the amplifier board to your desired listening level.
- Tone Control:
- Use the "TREBLE" knob to increase or decrease the high-frequency response of the main stereo channels.
- Use the "BASS" knob to increase or decrease the low-frequency response of the main stereo channels.
- Use the "SUBWOOFER" knob to adjust the output level of the dedicated subwoofer channel independently.
7. Maintenance
- Cleaning: Keep the module clean and free from dust. Use a soft, dry cloth for cleaning. Avoid using liquid cleaners or solvents.
- Environment: Operate the module in a dry, well-ventilated area. Avoid exposure to moisture, direct sunlight, or extreme temperatures.
- Ventilation: Ensure adequate airflow around the module to prevent overheating, especially during prolonged use at high volumes.
8. Troubleshooting
- No Sound Output:
- Check if the power supply is correctly connected and providing the specified voltage (12-26V DC).
- Verify that all speaker wires are securely connected to the correct terminals and that polarity is observed.
- Ensure your audio source is playing and its volume is turned up.
- If using Bluetooth, confirm the module is successfully paired with your device. If using AUX, ensure the cable is fully inserted into both the module and the audio source.
- Check the master volume knob on the amplifier board; ensure it is not set to minimum.
- Distorted Sound:
- Reduce the volume on both the amplifier module and your audio source. Overdriving the input or output can cause distortion.
- Ensure your speakers and subwoofer are compatible with the amplifier's power output and impedance (4-ohm recommended for 100W output).
- Check the quality of your audio source and cables.
- Verify that the power supply is stable and provides sufficient current.
- Bluetooth Disconnection:
- Ensure your audio source device is within the effective range of the Bluetooth module.
- Try unpairing and re-pairing the device.
- Check for potential interference from other wireless devices operating on the same frequency band.
9. User Tips
- Speaker Matching: For optimal performance and to achieve the rated 100W RMS output, use 4-ohm speakers. Using higher impedance speakers will result in lower power output.
- Power Supply Quality: A stable and clean DC power supply (12-26V) with adequate current capacity is crucial for minimizing noise and maximizing power output. Avoid using under-rated power supplies.
- Protection Features: The XY-S100H includes built-in protection against over-voltage, under-voltage, over-current, and short-circuits. While these features enhance safety, always ensure proper wiring and operation to prevent triggering them unnecessarily.
- Cable Quality: Use good quality audio cables and speaker wires to minimize signal loss and interference, ensuring the best possible sound quality.
10. Warranty and Support
The XINYI Sini Audio XY-S100H module is manufactured by CAIYUSHENG ELECTRONICS and is designed to meet high-quality standards. This product is compliant with relevant certifications such as CE, FCC, and RoHS, ensuring it meets safety and environmental requirements.
For any technical support, warranty claims, or inquiries regarding the product, please contact your point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.