RETEVIS RM01

Contents

Retevis RM01 VHF Marine Radio Transceiver User Manual

Model: RM01

1. Introduction

The Retevis RM01 is a VHF Marine Radio Transceiver designed for reliable communication in marine environments. It features IP67 waterproofing, a floating design, and a vibration draining function to ensure durability and performance even when exposed to water. This manual provides essential information for safe and effective use of your RM01 radio.

Video: Retevis RM01 Product Demonstration and Features Overview.

2. Safety Information

General Precautions

  • Always power off the radio in flammable and explosive environments.
  • The radio meets IPX7 waterproof requirements. However, if the radio has been dropped, its waterproof protection cannot be guaranteed due to potential damage to the sealed structure.
  • Ensure the earphone/charging jack cover and battery cover buckle are tightly fixed to prevent water leakage.
  • Use only the supplied AC adaptor or DC charger for charging.
  • When installing batteries, ensure positive (+) and negative (-) electrodes correspond correctly. Do not install them in the opposite direction.

RF Energy Exposure and Product Safety Guide

Before using this radio, read this guide which contains important operating instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.

  • This two-way radio uses electromagnetic energy (RF) for communication. Improper use can cause biological damage.
  • All Retevis two-way radios are designed, manufactured, and tested to meet government-established RF exposure levels.
  • Users should be fully aware of and able to control their exposure to meet occupational requirements.
  • To transmit on regulated radio frequencies, a license may be required from local radio management departments.
  • Unauthorized modifications or adjustments to the radio are prohibited and may void user authority.

Operating Instructions for RF Exposure Compliance

  • Transmit no more than 50% of the time. Transmitting 50% or less is important for compliance.
  • When operating in front of the face or body-worn, always place the radio in a Retevis approved clip, holder, holster, case, or body harness.
  • In hand-held mode, hold the radio vertically with the microphone at least 2.5 cm (one inch) away from the nose or lips. Keep the antenna away from the eyes.
  • In phone mode, hold the radio as you would a wireless telephone.

Electromagnetic Interference/Compatibility

  • Nearly every electronic device is susceptible to electromagnetic interference (EMI).
  • Turn off your radio in facilities where posted notices instruct you to do so (e.g., hospitals, aircraft, blasting sites).

Avoid Choking Hazard

This product contains small parts. Not for children under 3 years.

Protect Your Hearing

  • Use the lowest volume necessary.
  • Increase volume only in noisy surroundings.
  • Decrease volume before adding a headset or earpiece.
  • Limit the time you use headsets or earpieces at high volume.
  • Do not place the radio's speaker directly against your ear.
  • Excessive sound pressure from earphones and headphones can cause hearing loss.

3. Standard Accessories

Carefully unpack your radio and identify the following items before discarding packing materials:

ItemQuantityItemQuantity
Marine Transceiver1AAA NiMH Batteries5
Antenna1Belt Clip1
AC Adaptor1Hand Strap (Lanyard)1
DC Charger (Car Charger)1Instruction Manual1

Image: Package contents of the Retevis RM01.

Package contents including radio, batteries, antenna, chargers, belt clip, lanyard, and manual.

4. Get Acquainted: Parts and Controls

Familiarize yourself with the main components and controls of your RM01 radio:

Diagram of Retevis RM01 front panel with numbered parts.

Image: Front panel diagram of the Retevis RM01 showing numbered parts.

Keyboard Description

  1. [PTT] Key: Hold down to transmit, release to receive.
  2. Power Key (⑁): Hold for 1 second to power ON/OFF the radio.
  3. Channel 16/CALL Channel [C/16]: Press to select Channel 16. Hold for 1 second to select Call Channel. Hold for 3 seconds (when Call Channel is selected) to enter Call Channel programming mode. Press to exit menu mode.
  4. High/Low Power/Lock Key [LOCK]/[H/L]: Press to select high or low output power. Hold for 1 second to turn Lock Function ON or OFF.
  5. Menu Key [MENU]: Press to enter menu mode. Hold for 1 second to set or clear the TAG channel.
  6. Volume/Squelch/Monitor Key [VOL/SQL]/[MONI]: Press to enter volume adjustment mode. Press again for squelch adjustment mode. Hold for 1 second to activate Monitor function. Press [▲] while holding to turn on/off Volume Maximum Function. Press [▼] while holding to turn on/off Volume Mute Function.
  7. Up/Down Key [▲]/[▼]: While standby, press to select operating channel. In menu mode, press to select menu items. In channel scan, press to change scan direction.
  8. Antenna Connector: Connect with the supplied 50Ω antenna.
  9. Earphone/Charging [SP/MIC]/[CHR]: For connecting external earphone/microphone, or AC Adaptor/DC Charger. Rotate the jack cover counter-clockwise to open, clockwise to close. NOTICE: Make sure the jack cover is fixed tightly.

LCD Display Icons

IconDescription
TXAppears while transmitting.
LOWAppears when selecting low power. Flashes when forced to select low power.
USA/INT/CANAppears while respective Channel Group is selected.
BUSYAppears when channel is busy. Flashes while monitoring channel.
★Appears when TAG Channel is selected.
CALLAppears when Call Channel is selected.
Battery IconBattery indicator.
SCANFlashes while scanning.
Key Lock IconAppears while keyboards are locked.
DUPAppears while a duplex channel is selected.
DUALAppears while dual watch.
TRIAppears while tri-watch.
00/00Indicates the operating channel number or menu item options.
8888Indicates auxiliary channel or menu mode items.
Cloud IconAppears while weather alarm.
WXAppears while weather channel is selected.

5. Setup

Battery Installation

  1. Remove the battery cover by sliding the clip.
  2. Insert the 5 x 1.2V (AAA) NiMH batteries, ensuring correct polarity (+/-).
  3. Close the battery cover and secure the clip.
Image showing the battery compartment of the RM01 radio.

Image: Battery compartment of the RM01.

Image showing how to insert AAA batteries into the RM01 radio.

Image: Inserting AAA batteries into the RM01.

Charging the Batteries

  1. Plug the AC adaptor into an AC outlet, or the DC charger into a cigarette lighter.
  2. Rotate the earphone/charging jack cover counter-clockwise to open it.
  3. Insert the output terminal of the charging cable into the charging interface. The keyboard red light will turn on, indicating charging has started.

The charging time for NiMH batteries depends on their power level. Do not exceed 10 hours when the radio is OFF, and 18 hours when the radio is ON.

  • It is recommended to charge when the radio is powered OFF.
  • NOTICE: If alkaline batteries are used, NEVER charge, otherwise alkaline batteries and the radio will be damaged.
Diagram showing how to connect the AC adaptor or DC charger to the RM01 radio for charging.

Image: Charging setup for the Retevis RM01.

Antenna Attachment

Screw the supplied 50Ω antenna into the antenna connector on top of the radio until it is finger-tight.

6. Operating Instructions

Power ON/OFF

Hold down the Power Key (⑁) for 1 second to turn the radio ON or OFF.

PTT (Push-to-Talk) Key

Hold down the [PTT] key to transmit your voice. Speak with a normal tone. Release the [PTT] key to receive.

Channel Selection

  • Channel 16: Press the [C/16] key to select Channel 16, which is often used for distress and safety calls.
  • Call Channel: Hold the [C/16] key for 1 second to select the Call Channel.
  • Call Channel Programming: While the Call Channel is selected, hold the [C/16] key for 3 seconds to enter programming mode. Use [▲]/[▼] to select the desired channel, then press [C/16] to confirm.

High/Low Power Setting

Press the [LOCK]/[H/L] key to toggle between high (3W) and low (1W) output power. Low power conserves battery life, while high power provides longer communication distance.

Image illustrating selectable power output (3W for longer distance, 1W for longer battery life).

Image: Selectable power output (3W for longer call distance, 1W for longer battery life).

Volume and Squelch Adjustment

Press the [VOL/SQL] key to enter volume adjustment mode. Press again to enter squelch adjustment mode. Use [▲]/[▼] to adjust levels.

  • Hold [VOL/SQL] and press [▲] to activate/deactivate Volume Maximum Function.
  • Hold [VOL/SQL] and press [▼] to activate/deactivate Volume Mute Function.

Monitor Function

Hold the [VOL/SQL] key for 1 second to activate the Monitor function, allowing you to listen to weak signals.

Menu Operation

  1. Press the [MENU] key to enter menu mode.
  2. Use [▲]/[▼] keys to select the desired menu item.
  3. Press [MENU] again to enter the setting status for the selected item.
  4. Use [▲]/[▼] keys to select the desired setting.
  5. Press [C/16] to exit menu mode.

Channel Group Selection

The radio supports USA, International, and Canadian Channel Groups. In standby mode, press [MENU] then [LOCK] to switch between channel groups.

Weather Channel (NOAA)

The radio has 10 weather channels. In standby mode, press [MENU] then [VOL/SQL] to switch between the operating channel and weather channel. The RM01 supports NOAA's National Weather Service and can scan 10 NOAA radio channels. Setting a weather alert will automatically notify you of warnings from designated NOAA broadcast stations.

Image showing the RM01 radio with a stormy background and text '10 NOAA Channels'.

Image: The RM01 can receive 10 NOAA Weather Channels.

Scan Operation

Set the scan resume timer in menu mode.

  1. Enter the "Scdu" menu item to select Scan. Exit menu mode to start Normal Scan or Priority Scan.
  2. "SCAN" will flash on the LCD. "16" appears on the sub-channel readout during priority scan.
  3. The scan pauses when a signal is received (resume time can be set in the set mode). Channel 16 is monitored in priority scan.
  4. Use [▲]/[▼] to change the scan direction.
  5. Press [MENU] again, or [PTT]/[C/16]/[⑁] to stop scanning.

Watch Operation (Dual/Tri Watch)

The radio features Dual/Tri Watch, selectable in menu mode. This allows simultaneous monitoring of multiple channels.

  • Dual Watch: Monitors the current channel and Channel 16 alternately.
  • Tri Watch: Monitors the current channel, Channel 16, and the Call Channel alternately.

A "BEEP" sound indicates a signal received on Channel 16. Tri Watch switches to Dual Watch if a signal is received on the Call Channel.

Diagram explaining Dual Watch and Tri Watch functions on the RM01 radio.

Image: Dual/Tri Watch function diagram.

Vibration Water Draining Function

This function helps drain water from the loudspeaker housing, preventing water ingress from affecting voice quality.

  • In standby mode, press [MENU] then [⑁] to activate this function.
  • A deep sound will emit for 10 seconds to drain water. Any key operation is invalid during this process.
Image showing the RM01 radio vibrating to drain water out after being submerged.

Image: The RM01 radio demonstrating its Vibration Draining feature.

7. Maintenance

  • Keep the radio clean and dry.
  • Ensure all covers and buckles are securely fastened to maintain IP67 waterproofing.
  • Regularly check battery contacts for corrosion or debris.
  • If the radio has been submerged, use the Vibration Water Draining Function.
  • Do not use harsh chemicals or solvents for cleaning.

8. Troubleshooting

  • Radio not powering on: Ensure batteries are correctly installed and charged. Check battery contacts for proper connection.
  • Charging issues: Verify the charger is correctly connected to the radio and power source. Ensure the charging jack cover is fully open for connection. Remember, do not charge alkaline batteries.
  • Poor audio quality: Check if the Vibration Water Draining Function is needed if the radio has been exposed to water. Ensure the antenna is securely attached.
  • No signal reception/transmission: Verify the correct channel group is selected (USA/INT/CAN). Check antenna connection.

9. Specifications

CategoryItemSpecification
GeneralFrequency RangeTX: 156.000-162.000MHz, RX: 156.000-163.275MHz
Type of EmissionFM (16K0F3E)
Frequency Interval25kHz
NiMH BatteriesDC1.2V×5, 850mAh (AAA)
Operating Temperature-20℃ ~ +60℃
Waterproof LevelIP67 (1 Meter Depth of Water for 30 Minutes)
PhysicalDimensions (W×H×D)63mm×119mm×35mm
Weight (With Batteries)136g
Portable DesignLength: 270mm/10.6in, Width: 55mm/2.1in, Thickness: 34mm/1.3in, Weight: 480g (with belt clip and lanyard)
TransmitterOutput Power3W/1W
Output Current≤1.3A/0.8A
Max. Frequency Deviation±5kHz
Spurious Emission≤0.25μW
Adjacent Channel Power≥65dB
Transmit Audio Distortion≤5%
ReceiverReceiving sensitivity≤0.2μV
Signal-to-Noise Ratio≥40dB
Adjacent Channel Selectivity≥65dB
Spurious Response Immunity≥70dB
Audio Output Power≥0.6W

Image: Detailed technical specifications for the Retevis RM01.

Table of main parameters, receiver, and transmitter specifications.

10. User Tips

  • Battery Contacts: If your radio is not charging or powering on, ensure the battery contacts are clean and making good connection. Some users have found lifting the contacts slightly can help.
  • Charging: Always charge the radio when it is powered OFF for optimal battery life and to prevent potential damage.
  • Alkaline Batteries: Never attempt to charge alkaline batteries in the radio, as this can damage both the batteries and the device.
  • Water Exposure: After exposure to water, always use the Vibration Draining Function to expel water from the speaker and microphone areas.

11. Warranty and Support

Most new products carry a two-year manufacturer's warranty from the date of purchase. For warranty service, you will need to provide a receipt or proof of purchase from the actual seller for verification.

For further details and support resources (brochures, software/firmware, manuals), please contact your direct reseller or visit the official Retevis website: http://www.retevis.com/after-sale/

Exclusions from Warranty Coverage:

  • Damage caused by accident.
  • Misuse or abuse of the product, or unauthorized alterations or repairs.
  • If the serial number has been altered, defaced, or removed.

You can also find the user manual in PDF format for download: Retevis RM01 User Manual (PDF)

© 2023 RETEVIS. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.