VDIAGTOOL VD70 Lite

Contents

VDIAGTOOL VD70 Lite Diagnostic Tool User Manual

Model: VD70 Lite | Brand: VDIAGTOOL

1. Introduction

The VDIAGTOOL VD70 Lite diagnostic tool is designed to interface with a vehicle's Electronic Control Unit (ECU), enabling users to retrieve diagnostic trouble codes (DTCs), access real-time data streams, and perform active tests (bi-directional controls). It supports comprehensive diagnostics across multiple vehicle systems—including engine, transmission, anti-lock braking system (ABS), SRS (airbag), chassis, body, and more.

The tool allows simultaneous graphing of up to eight live data parameters on a single screen for efficient analysis and also provides detailed ECU information.

This chapter offers an overview of the diagnostic tool's core features, covering control buttons, data ports, battery pack, and power options. Technical specifications are provided at the end of the chapter.

Safety Information

To ensure your safety and prevent damage to the device or vehicle, please carefully read and follow all instructions in this manual before use.

When operating the device, always verify proper testing procedures and strictly adhere to the instructions provided. As automotive electrical systems may vary, you must assess potential risks and ensure a safe testing environment.

Always observe all safety warnings, use appropriate tools, and disconnect power sources when necessary. Improper operation may result in personal injury, equipment damage, or voided warranty.

Safety Messages

Safety messages use standardized signal words to indicate hazard levels and prevent injuries or equipment damage:

DANGER

Will result in death or serious injury if ignored. Indicates an immediately life-threatening hazard.

WARNING

Could result in death or serious injury if ignored. Indicates a potentially dangerous situation.

Safety Instructions

This manual covers known safety hazards, but cannot anticipate all possible risks. You are responsible for ensuring safe operating conditions and procedures.

DANGER

  • Always ventilate the service area when engine is running or use building exhaust removal system if available.
  • Carbon monoxide is odorless and deadly - can cause loss of consciousness or death.

WARNINGS

  • Always conduct testing in a safe, controlled environment.
  • Wear ANSI-approved safety goggles during all operations.
  • Keep all objects away from moving or hot engine components.
  • Ensure proper ventilation to avoid toxic exhaust fumes.
  • Secure the vehicle in PARK (automatic) or NEUTRAL (manual) with parking brake engaged.
  • Place wheel chocks and never leave the vehicle unattended during tests.
  • Exercise extreme caution around ignition systems - hazardous voltages are present.
  • Maintain an ABC-rated fire extinguisher within immediate reach.
  • Never connect/disconnect test equipment with ignition on or engine running.
  • Keep all test equipment clean, dry and free from contaminants.
  • Never operate test equipment while driving - focus solely on testing.
  • Strictly follow the vehicle service manual's diagnostic procedures.
  • Verify full battery charge and secure DLC connections before testing.
  • Never place test equipment near the distributor due to EMI risks.

Trademarks
VDIAGTOOL is a registered trademark of Shenzhen VDIAGTOOL Technology Co., Ltd in the United States and other jurisdictions. All other product names mentioned herein may be trademarks of their respective owners.

Copyright Information
© 2017 Shenzhen VDIAGTOOL Technology Co., Ltd. All rights reserved.

No reproduction, distribution, or transmission of this manual is permitted without express written authorization from VDIAGTOOL. This prohibition applies to all forms of copying including electronic, mechanical, photocopying, and recording.

Disclaimer & Liability Statement
Product Documentation Notice
All illustrations, specifications, and technical data in this manual are for reference only and subject to change without notice.
For the latest documentation, visit: www.vdiagtool.com/support/downloads

Limitation of Liability
VDIAGTOOL expressly disclaims all liability for:

  • Any direct, indirect, incidental, or consequential damages
  • Loss of profits or business interruption
  • Product modifications or unauthorized use

This manual does not:

  • Modify existing purchase/lease agreements
  • Create additional liabilities for VDIAGTOOL
  • Constitute additional product warranties

IMPORTANT:

Always consult this manual before operation, with special attention to all safety warnings. VDIAGTOOL reserves the right to modify product specifications at any time.

2. Setup and Getting Started

2.1 Data and Power Connections

The diagnostic tool uses a main cable with a DB15 male connector on one end (for the tool) and an OBDII-16 male connector on the other end (for the vehicle) to establish communication.

VD70 Lite device with data and power connections
VD70 Lite device with data and power connections. DB15 Male Connector connects to the diagnostic tool, OBDII-16 PIN Male Connector connects to the vehicle's OBDII port.

2.2 Battery Pack and Stand

Back view of VD70 Lite with battery pack and stand
Back view of VD70 Lite showing the battery pack and stand.

2.3 Power Sources

The VDIAGTOOL VD70 Lite diagnostic tool can be powered by either of the following sources:

  • Internal Battery Pack
  • AC Power Supply

Internal Battery Pack
The tool is equipped with an internal rechargeable battery that supports approximately 3.5 hours of continuous operation on a full charge.
The battery charges automatically when the device is connected to the AC power supply and a functioning AC power outlet.

AC Power Supply
The diagnostic tool can also be operated via a standard AC outlet using the provided AC power adapter. Connect the output cable of the adapter to the DC input jack located on the top of the device.
To ensure safety and compatibility, use only the original AC power supply included with the tool.

2.4 What's In The Box

ItemQuantity
VD70 Lite Diagnostic Tool1
Type-C to Type-A Adapter (for PC Connection)1
Type-C to Type-C Charger Cable1
Power Adapter (US Standard)1
Power Adapter (EU Standard)1
Power Adapter (UK Standard)1
DB15 Main Cable1
Color Retail Box1
Quick Start Guide1
Packing List1
Protective Hard Case1

2.5 Initial Powering On/Off

Ensure the diagnostic tool is adequately charged or connected to an external power source (refer to Power Sources on page 2 for details).

Note: The images and illustrations shown in this manual are for reference only and may differ slightly from the physical product.

Powering On, Off, and Force Restart
This section explains how to turn the VDIAGTOOL VD70 Lite diagnostic tool on and off, as well as how to perform an emergency shutdown when necessary.

2.5.1 Powering On
To turn on the device, press and hold the power button (located on the top-right side) for 3 seconds. The tool will power on if the battery is sufficiently charged or if it is connected to the AC power adapter.
If the battery is completely drained, allow the device to charge for a few minutes before attempting to turn it on.

2.5.2 Powering Off
To turn off the device, press and hold the power button for more than 3 seconds. The diagnostic tool will shut down automatically.

Important:

Always terminate all vehicle communication before powering off the diagnostic tool. A warning message will appear if you attempt to turn off the device while it is actively communicating with the vehicle.
Forcing a shutdown during communication may cause errors in the vehicle's ECM on certain models.
Never disconnect the DB15 main cable while the tool is communicating with the vehicle ECU.

2.5.3 Emergency Shutdown
Under normal circumstances, always power off the device using the standard procedure described in section 2.2. The emergency shutdown procedure should only be used if the diagnostic tool becomes unresponsive to button input or exhibits abnormal behavior.
To perform an emergency shutdown, press and hold the power button for 5 seconds until the device powers off.

Important:

Using emergency shutdown during active communication with a vehicle ECU may cause ECU malfunctions on certain models.

3. Operating the Diagnostic Tool

3.1 Overview of the Diagnostic Tool Interface

This chapter introduces the main diagnostic screen layout, key interface icons, and the Android system home screen along with its primary icons.

3.1.1 Diagnostic Screen Layout & Icons
Upon powering on, the diagnostic tool automatically launches the diagnostic application. The main diagnostic screen will appear once the program is loaded.

Main diagnostic screen interface of the VD70 Lite
Main diagnostic screen interface of the VD70 Lite.

A hidden toolbar is located at the bottom of the screen. Swipe upward from the bottom edge to temporarily display the toolbar, which remains visible for 3 seconds.
This section illustrates the layout of the diagnostic screen and the icons available in the toolbar.

3.1.2 Diagnostic Screen Icons

  • Auto Scan: Automatically identifies and decodes the vehicle's VIN, then performs a comprehensive diagnostic scan of all accessible electronic control modules.
  • Manual Diagnosis: Select this icon to access the diagnostic menu. From here, you can choose to identify the vehicle automatically by VIN, or manually specify the make, model, year, and other configurations. This section also provides access to the DEMO program and standard OBDII tests.
  • Special Function: This section provides access to commonly used vehicle maintenance and service functions, offering practical support for both DIY enthusiasts and professional technicians.
  • Report: This section provides access to diagnostic reports, data playback, and data review functions.
  • Updates: This section enables you to download diagnostic software updates individually or in batch.
  • More: This section allows you to manage user accounts and workshop profiles (where applicable), check subscription status, view firmware information, access the endoscope tool, and open the user manual in PDF format.
  • Settings: This section enables configuration of the diagnostic software language, measurement units, and USB mode. It also provides access to OS settings, including volume and display brightness adjustment. Additionally, you can view application version, OS version, diagnostic tool serial number, and VCI number here.
  • Remote Control: Select this icon to launch TeamViewer for remote assistance. Ensure TeamViewer is in "ready to connect" mode before your scheduled remote session. The TeamViewer ID is displayed on the right, and the connection status is shown at the bottom left of the screen.
  • Service Center: This section provides contact information and official social media accounts for customer support and other inquiries.

3.2 Hidden Toolbar and Home Screen

Swipe up from the bottom of the touchscreen to reveal the toolbar, which remains visible for 3 seconds. Tap the Home button on this toolbar to access the Android home screen of the diagnostic tablet.

3.2.1 Hidden Toolbar Icons

  • Screenshot icon: Takes a screenshot of what's on the screen.
  • Volume Down icon: Decreases the speaker volume.
  • Back icon: Returns to the previous menu or screen.
  • Home icon: Returns to the Android home screen.
  • Task List icon: Displays all ongoing tasks. Swipe up the respective task screen to kill the task.
  • Volume Up icon: Press to increase the speaker volume.
  • Diagnostic icon: Press to quickly launch the diagnostic application.
  • Screen Recorder icon: Press to start recording the screen and audio. Press again to stop recording.

3.2.2 Home Screen Layout

VD70 Lite Android home screen layout
VD70 Lite Android home screen layout.

3.2.3 Home Screen Icons

  • Calendar: Displays the calendar in day, week, or month view.
  • Camera: Activates the rear camera to capture images of vehicle components or issues.
  • VD70 Lite camera interface
    Camera interface for capturing images.
  • Contacts: Manage your contact list, add new contacts using the "+" icon, or import multiple contacts from a vcf file.
  • VD70 Lite contacts management screen
    Contacts management screen.
  • Clock: Set alarms, timers, use the stopwatch, or view the current time.
  • Email: Set up email accounts to send messages or share diagnostic reports.
  • Music: Play songs, create playlists, and manage music by albums or artists.
  • Sound Recorder: Record and play back audio messages.
  • Calculator: Perform basic mathematical calculations.
  • ES File Explorer: Manage documents, reports, and other files stored in the device memory.
  • Adobe Acrobat: View and manage PDF files. Connect to Dropbox with your accounts.
  • Quick Support: Allows our technical team to remotely control the tool to diagnose issues or provide guidance.
  • Endoscope: Use a connected endoscope for visual inspection. If no endoscope is connected, the built-in camera will activate automatically.
  • Settings: Configure system settings including Wi-Fi, battery, display, sound, and storage.
  • Gallery: View screenshots, camera photos, and screen recordings.
  • Video: Play recorded videos and screen recordings.
  • Explorer: Browse and manage files in internal memory.
  • Chrome: Browse the web to search for fault codes and other information.

3.3 Data Transfer via USB Type-C

To transfer data between the diagnostic tool and a PC:

  1. Connect the tool to a PC using the Type-C cable (to the device's Type-C port and the PC's USB port).
  2. Swipe down from the top of the screen to open the notification panel and tap Android System → Charging this device via USB.
  3. Select File Transfer.
  4. On the PC, open VD70 Lite to access files.

3.4 Red-Green Color Blindness Color Correction Mode

To enable color correction mode:

  1. Swipe up from the bottom to show the toolbar.
  2. Tap the Home button to go to the Android home screen.
  3. Go to Settings → Accessibility → Color correction and turn on Use color correction.

3.5 FCA AutoAuth - SGW

Security Gateway Module (SGW) - In 2018, the SGW was implemented by FCA USA to prevent unauthorized access. FCA said that SGW was developed to limit "the ability of non-registered and non-authenticated users to perform intrusive diagnostics such as "bi-directional controls", so users cannot directly clear the DTC, as well as any bi-directional control test (including actuation, relearn and calibration) on vehicles equipped with SGW.
VDIAGTOOL receives Certification by FCA to access SGW Module, and perform previously restricted actions, by registering with AutoAuth, an authentication service. VDIAGTOOL tablet scanner users can register through AutoAuth's Internet-based registration portal for $50 a year. (Note: This fee is NOT charged by VDIAGTOOL company.)
You can now access the SGW module and perform operations that were previously restricted by registering with the AutoAuth authentication service. This process eliminates the need for additional accessories. Users begin by registering through AutoAuth's web-based portal, selecting their desired package, and adding their VDIAGTOOL diagnostic tool.
The information above indicates that if you cannot find "Transmission" or a similar name in the diagnostic menu, you should locate "Transmission Oil Temperature" under the PID data (live data) menu of the Powertrain Control Module (or PCM). Similarly, if you are looking for the ABS Bleeding feature, you should go to the Special Function under the Brake Control Module (BCM). This approach helps navigate and locate specific diagnostic features within the diagnostic tool's interface.

3.6 Vehicle Diagnostics

This chapter outlines the basic operation of the diagnostic function.
The Diagnosis icon is located on the home screen. This function enables communication with the vehicle's electronic control systems, allowing you to:

  • Retrieve diagnostic trouble codes (DTCs)
  • View live PID data
  • Perform active tests
  • Access additional diagnostic functions

3.6.1 My Vehicles
The "My Vehicles" function allows you to save frequently used diagnostic programs for quick access.
To locate this feature, tap the Manual Diagnosis icon on the diagnostic screen. "My Vehicles" will be displayed in the top taskbar.
Adding Programs: Tap the "+" (add) icon, select the region of the vehicle brand, choose the desired brand(s), and tap "Complete" to confirm.
Removing Programs: Tap the pen (edit) icon, select the program(s) to remove, and tap "Remove" to confirm.

3.6.2 Compatibility Check
This diagnostic tool supports all OBDII/EOBD compliant vehicles for generic code reading and basic functions. It also covers a wide range of specific makes and models across the United States, Europe, Asia, Australia, and other regions for full-system diagnostics. Note that available functions may vary significantly, even between vehicles of the same make, model, and year.

Important:

Special Functions on the main diagnostic screen are not universally available for all vehicles. Feature availability is strictly determined by vehicle compatibility based on the VIN, make, model, and year.
To verify compatibility, contact support at support@vdiagtool.com or view the online reference list at: https://www.vdiagtool.com/support/vehicle-coverage (Note: The online list is for reference only and must be confirmed with technical support.)

3.6.3 Software Version
The current software version for each vehicle manufacturer is displayed at the bottom of its selection tile. For example, the installed HONDA software version is shown as V12.40 in the illustration below.

3.6.4 Demo Program
The DEMO program simulates the vehicle navigation process, available functions, and menu interfaces. You can use it to practice operating the diagnostic tool before performing actual vehicle diagnostics.

Important:

The DEMO program may not reflect the latest diagnostic procedures or actual vehicle screens. It is not intended for verifying vehicle coverage or compatibility.

3.6.5 Trial Mode
The diagnostic tool includes a limited number of trial uses. These allow you to evaluate its functions and check vehicle compatibility before activating a full subscription. The number of available trials may vary based on factory inspection procedures (including routine and random sampling).

3.6.6 Wi-Fi Connection
The diagnostic tool supports connections to both 2.4 GHz and 5.0 GHz Wi-Fi networks.

To connect to Wi-Fi:

  1. Swipe up to show the toolbar and tap Home.
  2. Go to Network & internet and turn on Wi-Fi.
  3. Tap the Wi-Fi icon, select a network, and enter the password.

To use a mobile hotspot:

  • iOS: Enable Allow Others to Join and Maximize Compatibility in Settings > Personal Hotspot.
  • Android: Enable the portable hotspot in Settings > Wireless & networks > Tethering & portable hotspot. Set encryption to WPA2 PSK and ensure a connection slot is available.

Note: Wi-Fi is not required for diagnosing most vehicles. It is only necessary for certain brands (e.g., Peugeot) that require online server access during diagnostics.

3.6.7 Product Activation
When the trial period ends, you must register and activate the diagnostic tool to continue using all diagnostic functions.

To activate the product:

  1. Tap Register.
  2. Enter your email address.
  3. Set and confirm your password.
  4. Agree to the User Terms and submit.

Once the registration complete message appears, the tool is activated. Your login credentials will be saved, and no repeated logins are required for future use.

Note:

If you are unable to register or do not see the activation screen, please contact our support team at support@vdiagtool.com or complete the technical support form on our website www.vdiagtool.com for immediate assistance.

3.6.8 Connecting the Main Cable
To establish communication between the diagnostic tool and the vehicle, please follow the steps below:

  1. Power on the diagnostic tool.
  2. Connect the DB15 male connector to the tool's DB15 female port and secure the screws.
  3. Plug the OBDII-16 male connector firmly into the vehicle's OBDII port.
  4. Turn the ignition to the "ON" position and launch the diagnostic program.

3.6.9 Vehicle Identification
Accurate vehicle identification is required for the diagnostic tool to establish communication and perform diagnostics. The identification process is menu-guided—follow the on-screen prompts to enter the necessary information. Specific steps may vary depending on the vehicle's make, model, and year.

You can identify a vehicle using one of the following four methods:

  • Auto Scan: Tap the Auto Scan icon on the diagnostic screen. The tool will automatically scan and decode the vehicle's VIN to identify it.
  • Important:

    A common misconception is that the tool cannot diagnose a vehicle if it fails to read or decode the VIN. If Auto Scan fails, try alternative identification methods. Manual Selection remains the most reliable fallback option.

    Note: Auto Scan is not supported on all vehicles. If unsuccessful, please use another identification method.

  • Manual Diagnosis: Tap the Manual Diagnosis icon on the diagnostic screen to open the vehicle selection menu. Then, tap the icon in the top left corner to access the Auto Scan and Manual Input options. Select Manual Input to enter the 17-digit VIN manually. The tool will decode the VIN and identify the vehicle.
  • Note: Some VINs cannot be decoded. If both Auto Scan and Manual Input fail, try Automatic Detection or Manual Selection instead.

  • Automatic Detection: Tap Manual Diagnosis, select the region of the vehicle brand (e.g., Americas), choose the brand (e.g., CADILLAC), and then select Automatic Detection to allow the tool to automatically identify the connected vehicle.
  • Note: Automatic Detection is not supported on all vehicle models. If this method fails, please use Manual Selection.

  • Manual Selection: If Auto Scan, Manual Input, and Automatic Detection fail to identify the vehicle, use Manual Selection—the most reliable method—to proceed with diagnostics.

To identify a vehicle manually:

  1. Tap Manual Diagnosis.
  2. Select the vehicle brand's region (e.g., Americas).
  3. Choose the brand (e.g., CADILLAC).
  4. Select Manual Selection.
  5. Specify the model year, model name, and any subsequent options until Automatic Scan and System Selection appear.

3.6.10 Submit Feedback
Tap the message icon in the top right corner to submit feedback to our support team regarding any issues with the app or software.

3.6.11 CAN Fast Scan
Rapidly scans all accessible vehicle systems for post-2005 vehicles using CAN protocol communication.

3.6.12 System Selection
Select a specific vehicle control module for diagnostics when you already have an idea which system may be causing issues.

3.6.13 Diagnostics
After successful vehicle identification, the diagnostic tool can scan and access the vehicle's electronic control systems to retrieve diagnostic trouble codes (DTCs), read PID data (Parameter IDs), view freeze frame information, access ECU details, and perform tests such as active tests (bi-directional controls), and more.

  • Read Codes: Displays diagnostic trouble code (DTC) records stored in the vehicle's electronic control modules. Selecting this option may open a submenu with additional viewing choices. If the tool displays "System is OK” or “No Trouble Code”, this may indicate:
    • No relevant fault codes are stored in the ECU;
    • The fault is not within that specific ECU's domain (e.g., mechanical or circuit issues);
    • A sensor signal is abnormal but still within its operational range — such cases can be further analyzed using Live Data (PID).
  • Clear Codes: Erases both current and historical DTC records, along with related data, from the vehicle's electronic control modules.
  • Note: Clearing codes will also erase freeze frame data.

  • PID Data: Displays real-time PID data from vehicle sensors and control modules. View data in list or graph formats, set custom value thresholds, and monitor up to 8 sensors simultaneously in list, individual graph, or merged graph views.
  • Freeze Frame: When a fault code is triggered, the vehicle ECU will save related data at that moment to generate a freeze frame. It is usually used to analyze the root cause that triggers the fault code, together with fault codes and PID data.
  • Active Tests (Bi-Directional Controls): Active tests, also referred to as bi-directional controls, verify the operation of specific actuators—including solenoids, valves, and relays.
  • Exiting Diagnostics: The diagnostic session remains active while communication with the vehicle is maintained. To exit diagnostics and power off the tool, the communication link must be properly terminated. A warning message will appear if an attempt is made to shut down during active communication.
  • Note: Disrupting communication during testing may cause damage to the vehicle's electronic control module (ECU). Always ensure the main cable remains securely connected throughout the process. Exit all tests before disconnecting the cable or turning off the diagnostic tool.

  • Full System Diagnostic Report: After completing diagnostics and returning to the main diagnostic screen, enter the VIN, mileage, and model year in the report generation form, then tap OK to create a diagnostic report for review or sharing.
  • Fault Code Report: Another way to generate a diagnostic report is through the Vehicle Scan / Auto Scan results. After scanning all available electronic control modules, a "Generate Report" option appears at the bottom. This produces a simplified diagnostic report showing only the retrieved fault codes and the affected vehicle systems.

4. OBDII/EOBD Functions

This chapter introduces the concept, protocols, test functions, and basic operations of the OBDII/EOBD feature. To access this function, navigate to: MANUAL DIAGNOSIS → Region Selection → OBDII

OBDII/EOBD provides a fast way to:

  • Retrieve DTCs and determine the cause of an illuminated Malfunction Indicator Lamp (MIL)
  • Check monitor status before emissions tests
  • Verify repairs and perform other emissions-related services

The OBDII function enables access to "generic” OBDII/EOBD data, which is limited to emissions-related diagnostics, including:

  • Reading emissions-related Diagnostic Trouble Codes (DTCs)
  • Identifying the cause of an illuminated MIL
  • Checking monitor status prior to emissions certification testing

IMPORTANT:

Generic OBDII/EOBD data is not included in engine system diagnostic data.

4.1 OBDII Protocols

Global OBD uses the following five communication protocols:

  • SAE J1850 PWM
  • SAE J1850 VPW
  • ISO 14230-4 (KWP2000)
  • ISO 9141-2
  • ISO 15765-4 / SAE J2480

4.2 Basic Operations

To access generic OBDII/EOBD data, follow these steps:

  1. Select MANUAL DIAGNOSIS on the main diagnostic screen.
  2. Choose the region of the vehicle manufacturer.
  3. Click the OBDII icon next to DEMO.

4.3 Auto Scan & Protocol Selection

There are two methods to access OBDII/EOBD data from the connected vehicle:

  • Auto Scan: When this option is selected, the diagnostic tool automatically attempts to communicate using each available protocol to identify the one utilized by the vehicle.
  • Protocol Selection: A communication protocol is a standardized method for data exchange between an ECM and the diagnostic tool. If the vehicle's protocol is known, you can manually select it to establish a direct connection.

4.4 10 Modes of OBDII

  • Mode $01 - Live Data
  • Mode $02 – Freeze Frame Data
  • Mode $03 - Stored Trouble Codes
  • Mode $04 – Clear/Reset Emission-Related Data
  • Mode $05 – Oxygen Sensors Test Results
  • Mode $06 – On-Board System Tests Results
  • Mode $07 – Pending Trouble Codes
  • Mode $08 – Control On-Board Systems
  • Mode $09 – Vehicle Information
  • Mode $0A – Permanent Trouble Codes

4.5 OBDII/EOBD Menu

4.5.1 Read Trouble Code
This option displays a list of current emission-related DTCs, including:

  • Stored Codes (Generic and Manufacturer-Specific)
  • Pending Codes
  • Permanent Codes

4.5.2 Generic & Manufacturer-Specific Codes
Code Definitions
Diagnostic Trouble Codes (DTCs) are used by OBDII systems to identify and communicate issues within the vehicle. The first character of a DTC indicates whether it is a generic code (applicable to all OBDII systems) or a manufacturer-specific code. The remaining three characters specify the affected system and circuit.

  • Generic Codes: DTCs with the second character as “0” are generic codes.
  • Manufacturer-Specific Codes: DTCs with the second character as “1” are specific to the vehicle manufacturer.

First DTC Character
The first character of a DTC is always a letter, indicating the general system where the fault is located. There are four types of codes:

  • P Codes: Powertrain – issues related to the engine, transmission, drivetrain, or fuel system.
  • C Codes: Chassis – problems in mechanical systems outside the passenger compartment, such as steering, suspension, or braking.
  • B Codes: Body – faults in components within the passenger compartment area.
  • U Codes: Network – problems with the vehicle's onboard computer systems or communication integration functions managed by OBD.

Second DTC Character
The second character in a DTC is a numeric digit—either “0” or “1”—that indicates the code's definition source:

  • 0: Indicates a standard SAE international code (also called a generic code), applicable to all OBDII-compliant vehicles.
  • 1: Represents a manufacturer-specific code (also referred to as an enhanced code), unique to the vehicle's make or model. For further details on such codes, consult the vehicle manufacturer directly.

Third DTC Character
If the second character is “0” (indicating a generic code), the third character specifies the malfunctioning subsystem. The values are defined as follows:

  • 0: Fuel and air metering and auxiliary emission controls
  • 1: Fuel and air metering injection system
  • 2: Fuel and air metering (injection system)
  • 3: Ignition systems or misfires
  • 4: Auxiliary emission controls
  • 5: Vehicle speed control, idle control systems, and auxiliary inputs
  • 6: Computer output circuit
  • 7-8: Transmission

Fourth and fifth DTC Characters
The fourth and fifth characters of a DTC form a two-digit number ranging from 00 to 99, known as the “Specific Fault Index.” This value identifies the exact nature of the malfunction.

4.5.3 Clear Trouble Code (Mode $04)
This function clears all emission-related diagnostic data—including DTCs, freeze frame data, and test results from the selected ECM's memory. Although OBDII/EOBD only displays generic data, clearing codes will erase all stored information, including enhanced codes and freeze frames.
A confirmation screen will appear to prevent accidental data loss. Select Yes to proceed.

4.5.4 Live Data (Mode $01)
This function displays real-time emission-related data from the selected electronic control module (ECM). The data is displayed in two columns: the left column shows parameter descriptions, and the right column displays the corresponding values, units, or states.

4.5.5 Read Freeze Frame (Mode $02)
Freeze frame data captures a "snapshot" of key parameter values at the moment a DTC is triggered. This function displays freeze frame data for stored emission-related DTCs. Typically, the stored frame corresponds to the most recent DTC. However, higher-priority DTCs—those with greater impact on emissions—may overwrite previous records, ensuring the most critical data is retained.

4.5.6 I/M Readiness (Smog Check)
This function checks the status of the vehicle's emission monitoring system, making it ideal for pre-inspection before state emissions tests. Selecting I/M Readiness opens a sub-menu with two options:

  • Since DTCs Cleared: Displays the status of emission monitors since the last time diagnostic trouble codes were cleared.
  • This Driving Cycle: Displays the status of emission monitors since the start of the current driving cycle.

4.5.7 O2S Monitoring Test (Mode $05)
This function provides a menu of tests to evaluate the integrity of oxygen sensors. Selecting a test displays all relevant O2S parameters, with the test identification (ID) shown at the top of the data list.

4.5.8 On-Board Monitor Test (Mode $06)
This function displays the results of On-Board Monitor tests, which are particularly useful after performing vehicle service or clearing control module memory.
A menu of available test results for monitored systems is provided, covering both continuously monitored components (e.g., misfire counters) and non-continuous monitors. Select a test to view its results.

4.5.9 Component Test (Mode $08)
This function enables limited bidirectional control of the ECM, allowing the diagnostic tool to operate specific systems, tests, or components—such as initiating an EVAP leakage test. It is useful for verifying whether the ECM responds correctly to commands.

4.5.10 Read Vehicle Information (Mode $09)
This function allows the diagnostic tool to request and display vehicle-specific information, such as the VIN, calibration identification, and CVN.

5. Special Functions & Maintenance Services

This chapter introduces various scheduled service and maintenance functions, also referred to as "Special Functions". These functions are typically presented as a series of menu-driven executable commands. By following the on-screen instructions—selecting appropriate options, entering correct values, and performing necessary actions—you will be guided through the complete process of executing each function.
Since vehicle configurations vary by model, specific operation steps for each function are not listed here. In general, please follow the prompts displayed on the tool screen.

For further assistance, please contact our support team at support@vdiagtool.com and provide the device serial number, vehicle VIN, and the required function.

5.1 Oil Reset

The diagnostic tool allows you to reset the engine oil life system, which estimates the optimal oil change interval based on driving conditions and climate. The oil life reminder must be reset after each oil change so the system can calculate the next service due date.

This function is used in the following scenarios:

  • The service lamp is illuminated, indicating required maintenance. After servicing, reset the mileage or time to turn off the lamp and start a new service cycle.
  • After an oil change or replacement of oil life monitoring sensors, the service lamp must be reset.

Operation Steps:

  1. Enter the Oil Reset menu and select the vehicle model.
  2. Follow the on-screen instructions specific to the vehicle and press OK after completing each step.
  3. Enter the maintenance mileage reset menu.
  4. Select INPUT, enter a reasonable value for the remaining oil life, and press OK.
  5. Confirm the [New Value] and select OK in the lower right to complete the process.
  6. A "Write successfully” message will appear upon completion.

5.2 EPB (Electronic Parking Brake)

The Electronic Parking Brake (EPB) reset function allows you to perform maintenance operations such as resetting the brake system, retracting or releasing brake pistons, and calibrating the G-sensor and vehicle level. It ensures safe and effective servicing of the electronic brake system, including deactivating/activating control systems, assisting with brake fluid procedures, and applying/releasing brakes after replacing pads or discs.

Typical Use Cases:

  1. After replacing worn brake pads or sensors, a reset is required to clear related fault codes and prevent false warnings.
  2. A reset is also necessary in the following situations:
    • The brake pad or wear sensor has been replaced
    • The brake pad indicator is illuminated
    • The brake sensor circuit is shorted
    • The servo motor has been replaced

Operation Steps:

  1. Enter the EPB menu and select the corresponding vehicle model.
  2. Follow the on-screen instructions and press YES when prompted.
  3. Enter Maintenance Mode, release the handbrake, and press OK.
  4. Wait for a "Successful operation” message, then press OK.
  5. Select Exit Maintenance Mode and confirm upon another success message.

5.3 SAS (Steering Angle Sensor)

Steering Angle Sensor (SAS) calibration permanently stores the current steering wheel position as the straight-ahead reference in the SAS EEPROM. Before calibration, ensure the front wheels and steering wheel are precisely aligned in the straight-ahead position. The VIN is also read from the instrument cluster and stored in the SAS EEPROM. By successful calibration, all SAS fault codes will be cleared automatically.
This procedure establishes the zero reference point for straight-line driving, enabling the ECU to accurately calculate left and right steering angles.

When to Perform SAS Calibration:
After any of the following services:

  • Replacing the steering angle sensor
  • Replacing steering mechanical components (e.g., gearbox, column, tie rod, knuckle)
  • Performing a four-wheel alignment
  • Repairing the vehicle body

Operation Steps:

  1. Enter the SAS menu and select the corresponding vehicle model.
  2. Choose Set steering angle sensor and follow the on-screen instructions.
  3. When prompted, press OK to proceed.
  4. Continue following the instructions and press Yes to confirm.
  5. Wait for the "Function execution is completed" message to indicate successful calibration.

5.4 BMS Reset (Battery Management System)

The Battery Management System (BMS) Reset function enables the diagnostic tool to evaluate the battery state, monitor current, register battery replacement, and activate the vehicle's rest state. This process clears existing low-battery fault information and performs battery matching to ensure accurate power management.

When to Perform BMS Reset:

  • After replacing the main battery, to clear previous fault data and prevent false detection by control modules.
  • To rematch the control module and monitoring sensor for accurate battery usage tracking, avoiding error messages on the instrument cluster.

Failure to reset may disable electric features such as auto start-stop, one-touch sunroof, or automatic power windows.

Operation Steps:

  1. Enter the BMS Reset menu and select the corresponding vehicle model.
  2. Turn on the ignition switch.
  3. Press OK to continue.
  4. Enter the battery capacity (within the specified range) and press OK.
  5. Enter the battery manufacturer and press OK.
  6. Enter the 10-digit battery serial number and press OK.

5.5 Injector Coding

This function writes the identification code of a fuel injector into the ECU, enabling the ECU to recognize and accurately control the new injector.
Injector coding is required after replacing the ECU or an injector to ensure proper cylinder-specific fuel injection control. Coding is typically not necessary after cleaning. The injector identification includes both precision and type values.
When replacing an injector, use a compatible model.
Most modern vehicles support injector coding.

Operation Steps:

  1. Enter the Injector Coding menu and select the appropriate chassis model.
  2. Choose Fuel Injection Nozzle Injection Volume Adjustment.
  3. Read the note carefully and press OK.
  4. Review and confirm the current values stored for each cylinder.
  5. For each replaced injector, enter the new 5-digit value and press OK. Wait for the "Write successfully" message.
  6. Turn off the ignition switch.
  7. When prompted, turn the ignition switch back on.
  8. Re-enter the adjustment menu to verify the new values.

5.6 TPMS Reset (Tire Pressure Monitoring System)

This function supports learning, matching, and resetting operations for tire pressure sensors.

When to Perform TPMS Reset:

  • After replacing tires
  • When troubleshooting tire pressure-related issues
  • When the tire pressure sensor signal is lost

Important Notes:

  • Some vehicle models require a TPMS activation tool for sensor matching.
  • After resetting, driving for a period may be necessary to clear the fault light.
  • Tire pressure imbalance can also trigger the tire pressure warning light.
  • This function only works with pre-activated sensors. For new sensors, use a professional TPMS tool.

Even for the same vehicle model, the tire pressure monitoring system may vary depending on the region of manufacture. To accommodate these differences, the TPMS Reset function provides six regional sub-menus covering major automotive manufacturing regions: Korea, Japan, USA, China, Australia, and Europe.

Select the sub-menu matching the vehicle's region of origin, then choose the specific model to continue.

TPMS reset can be categorized into four methods—Automatic Relearn, Static Relearn, Copy ID, and OBD Relearn—depending on the specific vehicle model. Even when the relearning methods share the same name, the actual procedures may vary.

  • Automatic Relearn:
    1. Install the tire pressure sensors correctly.
    2. Adjust all tire pressures to the specified values.
    3. Keep the vehicle stationary for over 20 minutes (engine and power off).
    4. Drive at 30–100 km/h for more than 15 minutes.
    5. The system will automatically relearn the sensor values, and the tire pressure warning will clear upon completion.
    6. If relearn fails, repeat steps 2–5.
  • Static Relearn:
    1. Install all tire pressure sensors correctly.
    2. Apply the parking brake.
    3. Turn the ignition to ON/RUN (engine off).
    4. Enter tire pressure learning mode via the instrument panel (methods vary by model; refer to the vehicle manual or consult a professional).
    5. Starting with the left front wheel (some models will flash the corresponding turn signal), activate the sensor using a TPMS Activation Tool. A horn sound or turn signal flash confirms successful activation.

    Note: Complete the first sensor activation within 2 minutes. If exceeded, repeat from step 4.

    1. After left front activation, proceed in order: right front → right rear → left rear. Success is indicated similarly to step 5.

    Note: Complete the remaining sensors within 3 minutes. If exceeded, restart from step 4.

    1. Turn off ignition and power. Adjust all tire pressures to specified values.
    2. The tire pressure warning light will clear after success. If failed, repeat steps 4–7.
  • OBD Relearn:
    1. A TPMS Activation Tool is required.
    2. Install all tire pressure sensors correctly.
    3. Adjust all tire pressures to the specified values.
    4. Activate the sensors in the following order: left front → right front → right rear → left rear.
    5. Connect the TPMS Activation Tool to the vehicle's OBD port and execute the OBD Relearn function to write the sensor IDs.
    6. Keep the vehicle powered off for more than 25 minutes.
    7. Drive at 30-100 km/h for over 15 minutes.
    8. If successful, the tire pressure warning light will turn off. Otherwise, repeat steps 4–7.
  • Copy ID Relearn:

    Note: This method requires copying the original sensor ID to the new sensor. If the new sensor does not support ID modification, it must be replaced using OEM-specific equipment.

    Method 1:

    1. Use a TPMS Activation Tool to read the original sensor ID.
    2. Program the copied ID into the new sensor (ensure ID format matches the original).
    3. Replace the original sensor with the newly programmed sensor and reinstall the tire.

    Method 2:

    1. Connect the TPMS Activation Tool to the OBD port, access the tire pressure system, and copy the target sensor ID.
    2. Program the copied ID into the new sensor (ensure ID format matches the original).
    3. Replace the original sensor with the newly programmed sensor and reinstall the tire.

    Method 3:

    1. Remove the original sensor.
    2. Manually copy the original sensor ID to the new sensor using the TPMS Activation Tool (ensure ID format matches).
    3. Install the new sensor, adjust tire pressure to the specified value, and reinstall the tire.

    Notes:
    A. Tire pressure standards are typically found in:

    • The vehicle owner's manual
    • A label near the driver's door (B-pillar)
    • The driver's side storage compartment
    • The fuel tank cap

    B. This diagnostic tool cannot perform the functions of a dedicated TPMS activation tool. It supports TPMS reset/relearn functions but cannot activate sensors. For professional TPMS tools, consult your local dealer.

5.7 ABS Bleeding (Anti-Lock Braking System)

The Anti-Lock Braking System (ABS) prevents immediate tire lock-up during braking. Maintaining ABS in optimal condition ensures full braking effectiveness, reduces braking time and distance, prevents skidding and loss of control during emergency stops, improves driving stability and steering control, and minimizes tire wear by avoiding excessive friction with the ground.
When air enters the ABS, the ABS Bleeding function must be used to purge the brake system and restore braking sensitivity.

When to Perform ABS Bleeding:

  • After replacing the front or rear brake distributor pump
  • Severe brake fluid loss
  • Brake fluid replacement

Operation Steps:

  1. Carefully read the on-screen instructions and precautions before starting. Ensure the vehicle and equipment are properly prepared.
  2. Attach a bleeder bottle to the left rear bleeder screw.
  3. Open the left rear bleeder screw.
  4. Click "OK" to begin the bleeding procedure. Continuously pump the brake pedal with steady applications every 2 seconds throughout the process.
  5. Continue pumping until no air bubbles are visible, then select OK to proceed to the left front wheel.
  6. Repeat the bleeding operation three times for each wheel in the following sequence: left front → right front → right rear.
  7. Stop pumping the brake pedal and close the right rear bleeder screw.
  8. Select OK to complete the procedure.

Cautions:

  • The ABS pump screw must be loosened before bleeding.
  • Brake fluid may be under pressure—secure the bleed hose and open bleeder screws slowly.
  • Some vehicles require manual bleeding instead of automatic support.

5.8 Power Balance

This function sequentially disables individual fuel injectors and monitors the corresponding drop in engine RPM. By comparing the power output reduction across cylinders, it identifies underperforming or malfunctioning cylinders based on their relative contribution to engine power.

5.9 Seat Calibration

Also referred to as Seat Configurations, this function is used to match or configure replaced or repaired seats equipped with memory functions.

5.10 EEPROM

This function requires the use of an EEPROM adapter (not included in the standard package) to read from and write data to EEPROM chips.

5.11 Language Change

This function allows you to modify the system language displayed on the instrument cluster or control console.

5.12 Transport Mode

Vehicles are placed in a partially activated state called Transport Mode during factory shipment to minimize battery drain. This function is used at the dealership to deactivate Transport Mode and fully enable all vehicle systems.

5.13 Control Unit Reset

This function resets the ECU software to resolve faults caused by abnormal operating temperatures or voltage fluctuations.

5.14 Throttle

Also referred to as Throttle Reset or Throttle Match, this function resets the throttle actuators and clears learned values stored in the ECU, restoring them to default settings. This ensures precise control of throttle or idle regulation and accurate adjustment of air intake.

5.15 A/F Reset

This function resets or relearns the air/fuel ratio parameters to optimize combustion efficiency.

5.16 HV Battery

This function checks the voltage of individual battery packs in hybrid or electric vehicles.

5.17 Gearbox Match

This function performs transmission self-learning to improve shift quality after disassembly or repair, resolving issues such as shifting delays or harsh engagement.

5.18 Crank Sensor Relearn

This function performs crankshaft position variation learning to turn off the Malfunction Indicator Lamp (MIL).
It is required in the following cases:

  • After replacing the engine ECU, crankshaft position sensor, or crankshaft flywheel.
  • When a DTC indicating "tooth not learned" is present.

5.19 Stop/Start Reset

This function enables or disables the automatic Start/Stop feature by modifying hidden settings in the ECU (requires vehicle hardware support and hidden function availability).

5.20 EGR Relearn

Also known as EGR Adaptation, this function recalibrates the Exhaust Gas Recirculation (EGR) valve after cleaning or replacement.

5.21 A/C Relearn

This function performs an AC system recalibration after replacing the AC ECU or actuator, or when ECU memory loss occurs.

5.22 Headlight

Also referred to as Headlight Adjustment, Headlight Matching, or AFS Reset, this function initializes the adaptive headlight system. It enables automatic headlight activation based on ambient light, and adjusts the lighting angle according to vehicle speed, body posture, and other driving conditions.

5.23 SRS (Supplemental Restraint System)

This function resets the acceleration sensor when replaced or when providing erroneous data to systems such as SRS, anti-theft, or navigation.

5.24 Windows Initialization

This function restores the power window automatic operation and ECU memory by performing window matching, typically required after vehicle battery disconnection causes window malfunction.

5.25 VGT Relearn (Variable Geometry Turbocharger)

Also referred to as VGT Turbo Calibration, this function calibrates newly installed variable geometry turbocharger (VGT) components. It is required after initial installation or replacement of a VGT, and when the component is detected operating outside its normal range.

5.26 Coolant Bleeding

Also known as Electric Water Pump Activation, this function activates the electric water pump following its replacement to ensure proper coolant circulation.

5.27 Suspension

This function adjusts the vehicle height sensor and performs level calibration in air suspension systems. It is used after replacing the height sensor or control module, or when the vehicle level is incorrect.

5.28 Tire Size Reset

This function resets the tire size configuration in the vehicle system when tires are replaced or upgraded.

5.29 Sunroof Initialization

When the vehicle battery is disconnected, the windows may not work right. This function is used to perform sunroof matching to recover the ECU initial memory, and recover the automatic ascending and descending function of power window.

5.30 TCM Oil Reset (Transmission Control Module)

The diagnostic tool can be used to reset the TCM oil life system, which calculates the optimum oil life change interval based on the vehicle's driving conditions and climate. The oil life reminder must be reset each time the oil is changed so that the system can calculate when the next oil change is due.

6. Settings

This chapter introduces the configuration options for the diagnostic software and tablet device, including language selection, measurement units, USB port mode, and other system preferences.

6.1 Language

To use the diagnostic program in your desired language, please contact our support team and provide the serial number (S/N) of your diagnostic tool to authorize the corresponding language software.

6.2 Unit

This setting offers three unit systems for measuring sensor values:

  • Metric Units: Centimeters, kilometers, grams, kilograms, °C, liters, Pa, kPa
  • Imperial Units: Inches, feet, yards, ounces, pounds, °F, PSI, miles, gallons
  • US Units: Inches, feet, yards, ounces, pounds, °F, PSI, mils, miles

6.3 USB Setting

This option allows you to configure the USB Type-C mode:

  • Data Transfer Mode: Enables data transfer between the Android tablet and a PC.
  • Expansion Mode: Connect extension accessories (e.g., EEPROM adapter).

6.4 Sound & Display

Adjust the volume of the built-in speaker and the brightness of the display screen.

6.5 Storage Management

This function provides access to manage your device's storage space. Here, you can delete content you no longer need (e.g., diagnostic packages) to free up space.

6.6 About

Displays the app version, OS version, diagnostic tool serial number (S/N), and VCI name. Also allows configuration of operating system settings.

7. Software Updates

This chapter explains the software subscription model and basic update procedures.

This diagnostic tool comes with free lifetime updates and does not require any additional subscription.

To update, connect the device to Wi-Fi or a mobile hotspot. A mobile hotspot is recommended for greater reliability and fewer restrictions compared to home Wi-Fi.

If a "Network abnormal” message appears, try an alternative network, check your router settings, or contact support at support@vdiagtool.com.

To update the software programs, you have two options:

  • Option 1: Update All Software Programs
    Tap "Update All" at the bottom right of the update screen to update all programs at once.
  • Option 2: Update Individual Software Program
    Tap the "Update" icon (↑) next to any program to update it individually. If the update is interrupted, tap the icon again to resume.

Delete Software Program:
If the diagnostic tool is running slowly due to limited storage space, you can free up memory by removing rarely used software programs.

To delete a diagnostic software program:

  1. Go to Manual Diagnosis → Select Region.
  2. Press and hold the icon of the vehicle manufacturer you wish to remove.
  3. Tap "Delete" in the menu that appears.

8. Troubleshooting and FAQs

This section addresses common questions and issues users may encounter.

8.1 General FAQs

Q1: Why can't I find the I/M Readiness function in the menu?
A: To access I/M Readiness, enter Manual Diagnosis, select the region (e.g., America/Europe/Asia), tap the "OBDII" icon in the upper-left corner, perform an Auto Scan or manually select the OBDII Protocol, and then choose I/M Readiness from the menu.
Q2: Why can't I find live sensor data such as Short-Term/Long-Term Fuel Trim like a generic OBD2 scanner?
A: To access live OBD2 data (including LTFT and STFT), please enter Diagnosis, select the appropriate region (e.g., America / Europe / Asia), tap the "OBDII" icon in the upper-left corner, perform an Auto Scan or manually choose the OBDII Protocol, enter Live Data, and then select the desired parameters such as LTFT, STFT, or related terms.
Q3: Why can't I find misfire data for my Ford/Dodge/Chrysler/Jeep vehicle?
A: To access misfire data, please navigate as follows: Manual Diagnosis → select region (e.g., America/Europe/Asia) → tap the OBDII icon (located in the upper-left corner) → perform an Auto Scan or manually select the OBDII Protocol for your vehicle → enter On-Board Monitor Test → then choose "Misfire Cylinder Data" or a similar menu option.
Q4: How can I export live data as a CSV file?
A: To generate a CSV file: While viewing Live Data, tap the Menu or Export icon, select Custom or set desired parameters, then choose Export to CSV or a similar option.
To locate the exported file: Open ES File Explorer, navigate to Internal Storage → diagnosis → csv_records, and your CSV files will be stored there.
Q5: The device is not charging when plugged in. The battery is very low (around 10%). What should I do?
A: Please charge the device for at least one hour, then unplug the USB-C cable, press and hold the power button for 15 seconds, release it, and check if the device powers on successfully.
Q6: When activating the device, shows error message "registration failure" after entering your email address.
A: This issue is often network-related; please try using a mobile hotspot (recommended) or switching to a different Wi-Fi network, then attempt activation again.
Q7: When entering the diagnosis software, error messages such as "license exception" or "Failed" are displayed. How can this be resolved?
A: Please try pressing and holding the diagnosis software icon to uninstall it, then re-download the software from the "Updates" section. If the issue continues, contact our support team at support@vdiagtool.com with your diagnostic tool's serial number (S/N) for further assistance.
Q8: I cannot update. I've tried both Wi-Fi and mobile hotspot, but it keeps showing connection failure. What should I do?
A: This issue is commonly caused by network restrictions, such as router firewall settings or regional network limitations. Please check whether your network allows access to the update server. If the problem continues, contact our support team at support@vdiagtool.com for assistance.
Q9: Is it possible to install the Google Play Store on the diagnostic tool?
A: This device does not support the Google Play Store. If you wish to install a third-party application, you may manually install it via an APK file. Please note, however, that we do not recommend installing third-party apps as they may impact device performance and stability.
Q10: Why can't the automatic VIN feature recognize my vehicle?
A: Automatic VIN scanning may not work on all vehicles. This can occur if the VIN is not stored in the ECU, is not yet included in our database, or if the vehicle (such as some Dodge models) uses a command-based communication protocol. You can try the following alternatives:
  • Turn the ignition ON but do not start the engine, then attempt an auto scan. For older vehicles, try with the engine running.
  • Manually enter the VIN.
  • Navigate to: Diagnosis → Select Region → Vehicle Selection → Automatic Detection.
  • Navigate to: Diagnosis → Select Region → Vehicle Selection → Manual Selection.
Q11: Why can't my diagnostic tool connect to Wi-Fi?
A: Connection issues can arise from several causes. Please try the following solutions based on your situation:
  • If the connection times out, check your router settings. Ensure it is set to WPA2 (not WPA3) for maximum compatibility, and confirm it does not block traffic to regions like China. Using a mobile hotspot often resolves this; you can switch back to your home Wi-Fi after activation.
  • If you use a Wi-Fi extender, try disconnecting from the main router and connecting directly to the extender.
  • If the tool is connected to the internet but displays "connect internet to sync your device,” the issue may be a time zone mismatch. Please set the time zone to Pacific Time by going to: Main Screen → Settings → System → Date & Time → Select Time Zone.
Q12: How can I change the menu language to Spanish?
A: To use the diagnostic tool in Spanish, please contact support@vdiagtool.com with your device's serial number (S/N) to request authorization for the Spanish software. Once authorized, go to Settings → Language and select Spanish, then navigate to Updates to download and install all available Spanish software packages. After installation is complete, the interface will be fully available in Spanish.
Q13: Why does the scanner show "report shared successfully," but I don't receive the email?
A: Reports are sent from our email address: noreply@service-vdiagtool.com. Even if the device shows "send successfully," your email provider may block this message. Since you use Gmail, you can try whitelisting our sender address to prevent blocking. Instructions can be found here: https://downtimemonkey.com/blog/how-to-whitelist-an-email-address-in-gmail.php
Note that not every user needs to set up a whitelist, as blocking does not always occur. You may also check your spam or junk folder for messages from noreply@service-vdiagtool.com.

9. User Tips

Based on common user inquiries and feedback, here are some helpful tips for using your VD70 Lite Diagnostic Tool:

  • Keep Software Updated: Regularly check the 'Updates' section to ensure your diagnostic software is current. This ensures compatibility with the latest vehicle models and access to new features.
  • Utilize Manual Selection for Tricky VINs: If the 'Auto Scan' feature struggles to identify your vehicle's VIN, don't hesitate to use 'Manual Selection'. It's the most reliable method for ensuring accurate diagnostics.
  • Backup Data Regularly: Export important diagnostic reports and live data as CSV files to your PC. This provides a secure backup and allows for more in-depth analysis using external tools.
  • Connect to Stable Wi-Fi for Updates: For software updates, a stable Wi-Fi connection or a mobile hotspot is recommended over less reliable networks to prevent interruptions.
  • Familiarize with OBDII Modes: Understanding the 10 modes of OBDII can help you quickly navigate to specific diagnostic data, such as Live Data (Mode $01) or Freeze Frame Data (Mode $02).
  • Use Remote Control for Support: If you encounter complex issues, the built-in TeamViewer 'Remote Control' feature allows VDIAGTOOL's technical support to assist you directly.

10. Technical Specifications

ItemDescription / Specification
Display7-inch touch screen, 1024 × 600 resolution
Operating SystemAndroid 10.0
ProcessorQuad-core, 1.5 GHz
Memory2GB RAM + 64GB ROM
ConnectivityBluetooth 4.1, Wi-Fi (2.4GHz & 5GHz), Type-C
SensorGravity accelerometer, Ambient light sensor
AudioBuilt-in microphone
SpeakerBuilt-in speaker
Camera8-megapixel
Battery Capacity18.25Wh (DC 7.3V, Rechargeable Li-ion, 2500mAh)
Tested Battery Life3.5 hours (continuous operation)
Power AdapterInput: 100-240V AC, Output: 5.0V=3.0A
Operating Voltage9V – 36V
Dimensions240 × 150 × 36.4 mm (9.45 × 5.91 × 1.43 in)
Net Weight0.91 kg (2.0 lbs)
Gross Weight2.2 kg (4.85 lbs)
Operating Temperature0°C to 40°C (32°F to 104°F)
Storage Temperature-10°C to 50°C (14°F to 122°F)
Operating Humidity<90% RH (non-condensing)

11. Warranty and Support

11.1 Limited Two-Year Warranty

This warranty is expressly granted to buyers who purchase the VDIAGTOOL VD70 Lite product for resale or for use in the ordinary course of their business.
VDIAGTOOL warrants that the VD70 Lite diagnostic tool shall be free from defects in materials and workmanship for a period of two years (24 months) from the date of delivery to the original buyer.

This warranty does not cover any part that has been subjected to misuse, alteration, used for unintended purposes, or operated in a manner inconsistent with the product instructions. The exclusive remedy for any tool found to be defective under this warranty shall be, at VDIAGTOOL's option, repair or replacement of the product. VDIAGTOOL shall not be liable for any consequential or incidental damages arising from the use or inability to use the product.

11.2 Contact Us

Warranty & Support
Email: support@vdiagtool.com
Website: www.vdiagtool.com

Product Support & Training Resources
Technical Support

Training Videos
Free product operation videos:

  1. Visit Training Center: https://www.vdiagtool.com/support/training-center
  2. Select Diagnostic Tools category
  3. Watch model-specific tutorials

Follow Us on Social Media

  • Facebook Page: Search for "vdiagtool"
  • Facebook User Group: Search for "VDIAGTOOL OFFICIAL User Group"
  • Instagram: Search for "vdiagtool_official"
  • TikTok: Search for "vdiagtool_us"
  • YouTube: Search for "Vdiagtool Official"

11.3 Service Center

This section provides various ways you can contact us, including warranty claims, technical support, video tutorials, marketing collaboration, business opportunities, and feedback to help us improve diagnostic tools.

Remote Control
This function allows you to request remote assistance from our technical team. They can directly operate the diagnostic tool to help you with unfamiliar functions or procedures.

To use remote assistance:

  1. Ensure your diagnostic tool is connected to a Wi-Fi network.
  2. Tap the "Remote Control” icon to launch TeamViewer.
  3. Wait until the status "Ready to connect (secure connection)” appears at the bottom left of the screen.
  4. Provide the TeamViewer ID (displayed in the center-right of the screen) to our support team when scheduling a remote session in advance.

Schedule a Remote Control
To schedule a remote assistance session with our technical team, please follow these steps:

  1. Visit our official website: www.vdiagtool.com
  2. Navigate to "Support" → "Tech Support", or directly access: https://www.vdiagtool.com/support/tech-support
  3. Complete the “Remote Assistance” form with your request and details.

Data Logging
For software-related issues—such as vehicle communication failures or function errors—data logs are often essential for effective troubleshooting. To ensure our technical team can retrieve and analyze these logs, please keep your diagnostic tool connected to Wi-Fi for at least 15 minutes and provide its serial number (S/N) when submitting a support request.

12. Compliance Information

12.1 Regulatory Compliance Statements

United States (FCC)
FCC ID: 2BE93VDT700
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

Interference Guidance: If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Warning:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

12.2 RF Exposure & SAR (FCC & ISED)

This device complies with FCC and ISED Canada RF exposure guidelines. Its radiated output power is below the radio frequency exposure limits.
The Specific Absorption Rate (SAR) is measured using standard operating positions with the device transmitting at its highest certified power level. The FCC SAR limit is 1.6 W/kg. The device is designed to operate at multiple power levels to minimize exposure and uses only the necessary power to maintain communication.
To ensure compliance with RF exposure requirements, minimize human contact with the antenna during normal operation.

12.3 Additional Compliance (RoHS, CE & UKCA)

RoHS: This product is compliant with Directive 2011/65/EU on the restriction of hazardous substances.

CE: This product conforms to the essential requirements of the following European Directives:

  • EMC Directive 2014/30/EU
  • RED Directive 2014/53/EU
  • Low Voltage Directive 2014/35/EU

UKCA: This product is declared to conform to the essential requirements of the relevant UK statutory instruments and carries the UKCA mark accordingly.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.