QIACHIP KT05-ABCD-4, RX480E-4

Contents

QIACHIP 433 MHz RF Remote Control Transmitter and Receiver Switch Module User Manual

Model: KT05-ABCD-4 (Transmitter), RX480E-4 (Receiver)

Brand: QIACHIP

1. Introduction

This manual provides detailed instructions for the QIACHIP 433 MHz RF Remote Control Transmitter and RX480E-4 Receiver Switch Module. It covers product features, applications, setup, operating modes, wiring, and important precautions to ensure safe and effective use.

For a downloadable PDF version of the user manual, please refer to the official product page or contact customer support.

2. Product Features

  • Working Voltage: DC 3V-5V
  • Working Frequency: 433.92MHz (RX480E-4); 315MHz (RX480E-3)
  • Receiving Sensitivity: -108dBm
  • Good selectivity and stray radiation suppression ability, easy to pass CE / FCC international certification
  • Temperature Range: -40~85℃
  • Ultra small size: 28×12×8mm (Including pin thickness)

3. Applications

The QIACHIP RF Remote Control system is versatile and can be used in various applications:

  • Wireless power switch and socket
  • Remote control for curtains, access control, and electric vehicles
  • Security and monitoring systems
  • Hotel room control
  • Smart home products
  • Electric cars, motorcycles, automobile anti-theft products
  • Remote door openers, closers control systems
  • Home security products, electric doors, alarm host, alarm systems
  • Room controls, shutter doors, windows
  • Remote control sockets, LED lighting, audio systems
  • Remote control electric doors, garage doors, retractable doors, rolling gates, sliding doors
  • Remote control curtains, MP3 players, audio systems
Diagram showing various applications like electronic rolling gates, garage doors, retractable doors, and vehicles.
Figure 1: Common applications for the RF remote control system.

4. Specifications

AttributeValue
ModelKSL-RX480E-4 (Receiver), KT05-ABCD-4 (Transmitter)
Working VoltageDC 3.3V-5V
Working Frequency433 MHz (RX480E-4), 315 MHz (RX480E-3)
Frequency Band±0.2MHz
Receive Sensitivity-108dBm
Quiescent Current<=5mA
Receive Distance20-100M (open space)
Working Temperature-25~75°C (Receiver), -40~85°C (Module)
Wireless CommunicationRF
Channel4
Matching ModeIntelligent Learning Code
Working ModeMomentary, Toggle, Latching
Module Dimensions28×12×8mm (Including pin thickness)
CertificationCE
Diagram showing the dimensions of the RX480E-4 receiver module, which is 28mm long and 12.3mm wide.
Figure 2: RX480E-4 Receiver Module Dimensions.

5. Setup

5.1 Pin Definition and Module Layout

The RX480E-4 receiver module features 8 pins. Understanding their function is crucial for proper setup.

Bottom view of the RX480E-4 receiver module showing the pin labels: GND, +V, D0, D1, D2, D3, VT, ANT.
Figure 3: RX480E-4 Receiver Module Pinout.
Pin No.NameDescription
1GND (-)Negative pole of power supply
2V (+)Positive electrode of power supply (3V-5V)
3D0Signal output pin corresponds to remote control button value 1 (0001)
4D1Signal output pin corresponds to remote control button value 2 (0010)
5D2Signal output pin corresponds to remote control button value 4 (0100)
6D3Signal output pin corresponds to remote control button value 8 (1000)
7VTExternal pairing button (High level active)
8ANTAntenna

5.2 Wiring Instructions

The module uses 2.54mm standard spacing 4-pin connectors. Ensure correct polarity and voltage when connecting.

Close-up of the RX480E-4 receiver module showing the learning button and pin headers.
Figure 4: RX480E-4 Receiver Module with Learning Button.

Connected to LED Circuit Diagram

Wiring diagram for connecting the RX480E-4 receiver module to LEDs, showing connections for GND, +V, D0, D1, D2, D3, and VT with an external pairing button and indicator light.
Figure 5: Wiring Diagram for LED Output.

Connected to Relay Circuit Diagram

Wiring diagram for connecting the RX480E-4 receiver module to a ULN2003 driver chip and four 12V relays, with a 78L05 voltage regulator for power supply.
Figure 6: Wiring Diagram for Relay Output.

5.3 Antenna Installation

Proper antenna installation is crucial for optimal range and performance. The module supports both 315M and 433M antennas.

General Application Antenna (433M)

  • Antenna core diameter (including outer skin): 1.0mm
  • Antenna core diameter (excluding outer skin): 0.35mm
  • Length of wire at welded end: 12mm
  • Diameter of antenna winding (excluding outer skin): 3.0mm
  • Winding turns: 26 turns
  • Length of winding: 36mm
Diagram showing the specifications for a 433M antenna: 3.0mm winding diameter, 12mm wire length at welded end, 26 turns, and 36mm winding length.
Figure 7: 433M Antenna Specifications.

General Application Antenna (315M)

  • Antenna core diameter (including outer skin): 1.0mm
  • Antenna core diameter (excluding outer skin): 0.5mm
  • Length of wire at welded end: 17.5mm
  • Length of wire at antenna end: 9.5mm
  • Diameter of antenna winding (including outer skin): 5mm
  • Winding turns: 15
Diagram showing the specifications for a 315M antenna: 5mm winding diameter, 17.5mm wire length at welded end, 9.5mm wire length at antenna end, and 15 turns.
Figure 8: 315M Antenna Specifications.

Special Enhanced Antenna (for longer communication distance)

  • Antenna core diameter (including outer skin): 1.2mm
  • Antenna core diameter (excluding outer skin): 0.5mm
  • Length of wire at welded end: 20mm
  • Diameter of antenna winding (excluding outer skin): 6.8mm
  • Winding turns: 13 turns
  • Length of winding: 23.5mm

6. Operating Instructions

6.1 Programming Modes

The receiver module supports three main working modes: Momentary, Toggle, and Latching. These modes are set during the pairing process using the learning button on the receiver module.

Close-up of the RX480E-4 receiver module showing the learning button and text descriptions for Inching Mode (Momentary), Self-Lock Mode (Toggle), and Interlocked Mode.
Figure 9: Learning Button and Mode Selection.

Momentary Mode (Inching Mode)

  • When the corresponding button of the remote controller is pressed, the pin corresponding to RX480E outputs a high-level signal "1".
  • When the remote controller button is released, the pin corresponding to RX480E outputs a signal "0".

Toggle Mode (Self-Lock Mode)

  • When the corresponding button of the remote controller is pressed once, the pin corresponding to RX480E always outputs a high-level signal "1".
  • When the same button of the same remote controller is pressed once again, the output signal of the pin corresponding to RX480E becomes "0".

Latching Mode (Interlocked Mode)

  • When the "A" button of the remote controller is pressed once, the "D3" pin of the RX480E always outputs the high-level signal "1".
  • When the "B" button of the remote controller is pressed once, the "D3" pin of the RX480E outputs the signal "0", and the "D2" pin of the RX480E always outputs the high-level signal "1".

6.2 Programming Steps

  1. Delete Existing Data: Press the learning button on the receiver module 8 times. The LED will flash 7 times to indicate successful data deletion.
  2. Learning Remote Code:
    • Press the learning button once for Momentary Mode.
    • Press the learning button twice for Toggle Mode.
    • Press the learning button three times for Latching Mode.
    • Press the learning button four times for Two-way Toggle + Two-way Momentary mode.
    • Press the learning button five times for Two-way Momentary + Two-way Latching mode.
    • Press the learning button six times for Two-way Toggle + Two-way Latching mode.
    • Press the learning button seven times for Two-way Latching + Two-way Latching mode.

    After pressing the learning button the desired number of times, the LED will turn on, indicating that learning mode is active. Then, press any button on your remote control. The LED indicator will flash three times, confirming successful learning.

  3. Test: After completing the programming, the receiver board should now be controllable by the remote control.

You can learn and store more transmitters with different IDs by repeating step 2. A mixture of different modes is possible.

6.3 Video Demonstration

Video 1: Demonstration of setting working modes (Inching, Self-Lock) for the RF receiver module using the learning button and a transmitter.

7. Maintenance

To ensure the longevity and optimal performance of your QIACHIP RF Remote Control system, follow these maintenance guidelines:

  • Keep the modules clean and free from dust and moisture.
  • Avoid exposing the modules to extreme temperatures or direct sunlight.
  • Regularly check wiring connections for any signs of wear or damage.
  • Ensure the power supply is stable and within the specified voltage range (DC 3.3V-5V).

8. Troubleshooting

If you encounter issues with your RF Remote Control system, consider the following:

  • No response from receiver: Check power connections to the receiver module. Ensure the transmitter has a working battery. Verify that the remote control is paired correctly with the receiver (re-do programming steps if necessary).
  • Limited range: Check the antenna connection on the receiver module. Ensure the antenna is properly sized and positioned. Avoid obstructions between the transmitter and receiver.
  • Interference: Ensure the device is well grounded. If the power supply is unstable or has large ripple, add a filter at the power input.
  • Incorrect mode behavior: Re-program the receiver module to the desired mode (Momentary, Toggle, or Latching) following the programming steps.

9. Precautions

  • This product is a CMOS device. Pay attention to anti-static measures during storage, transportation, and use.
  • The device must be well grounded during use.
  • RF devices are voltage-sensitive. If the power supply is unstable or has a large ripple, add a filter at the power input to ensure the supply voltage does not exceed the maximum working voltage of the product.
  • Ensure the transmitter encoding type is compatible (e.g., EV1527 PT2262). Incompatible transmitters will not work with the receiver.

10. User Tips

  • Power Supply: The receiver module requires a DC 3.3V-5V power supply. Ensure your power source provides stable voltage within this range for optimal performance.
  • Transmitter Battery: While the receiver module is powered externally, the remote control transmitter will require its own battery. Check the transmitter's specifications for the correct battery type and replacement instructions.
  • Experiment with Modes: The different operating modes (Momentary, Toggle, Latching) offer flexibility for various projects. Experiment to find the best mode for your specific application.

11. Warranty and Support

QIACHIP products are designed for reliability and performance. For any technical assistance or support, please contact the seller or refer to the official QIACHIP RF Remote Store. Keep your purchase records for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.