dawupine Subterrene-MWQ

Contents

PPR Water Pipe Hot Melt Device Instruction Manual

Model: Subterrene-MWQ | Brand: dawupine

1. Introduction

This Portable Digital Display PPR Water Pipe Hot Melt Device is designed for efficient and reliable welding of plastic pipes. It features high power, fast heating, and intelligent temperature control for uniform and stable heat conduction. The device is powered by a compatible 18V Li-ion battery (not included), offering wireless convenience for various construction scenarios.

2. Important Safety Warnings

TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE.

Keep this manual in a safe, dry place for future reference.

General Safety Rules:

  • This device is intended for use by individuals 8 years of age and older with appropriate supervision and understanding of hazards. Children must not play with this device.
  • Cleaning and user maintenance should not be performed by children without supervision.
  • Do not expose to rain. Store indoors.
  • Use only as described in this manual. Use only accessories recommended by the manufacturer.
  • Do not operate this product with wet hands.
  • Do not put anything into the opening.
  • Keep hair, loose clothing, fingers, and all body parts away from openings and moving parts.
  • Turn off all controls before removing the battery.
  • Do not use near open flames, hot embers, or explosive atmospheres, such as the presence of flammable substances, liquids, gases, or dust. Cordless tools can create sparks that may ignite dust or fumes.
  • Do not use if there are broken, bent, cracked, or damaged parts. Any device showing damage or malfunction should be repaired by a professional.
  • Do not leave the device powered on and unattended.

Battery Safety:

  • Always turn off the device before installing or removing the battery.
  • When installing or removing the battery, hold the device and the battery firmly. Failure to hold them firmly can cause them to slip out of your hands, resulting in damage to the device, battery compartment, and personal injury.
  • Fully install the battery. Otherwise, it could accidentally fall out of the device, causing injury to you or those around you.
  • Do not use force when installing the battery case. If the battery compartment does not slide in easily, it is not inserted correctly.
  • This product does not include batteries.

3. Package Contents

Please check the package for the following items:

  • 1 x Lithium Electric Fuser (Main Unit)
  • 6 x Replacement Scalding Heads (20mm, 25mm, 32mm pairs)
  • 1 x Wrench
  • 2 x Nuts
Package contents including the hot melt device, wrench, nuts, and three pairs of scalding heads (32mm, 25mm, 20mm).
Figure 3.1: Included components of the hot melt device kit.

4. Setup

4.1. Battery Installation

This device is designed to be powered by a Milwaukee 18V Li-ion Battery (not included). Ensure you have a compatible battery before use.

  1. Align the tabs on the battery with the grooves in the device's housing.
  2. Slide the battery into place until it locks with a click.
  3. To remove the battery, press the release button and slide the battery out.

Important: This device is NOT suitable for Milwaukee "V18" or "48-11-2200" series lithium batteries.

Image showing the correct battery slot for compatible Milwaukee 18V Li-ion batteries.
Figure 4.1: Compatible battery slot for Milwaukee 18V Li-ion batteries.
Image showing incompatible Milwaukee V18 and 48-11-2200 series lithium batteries marked with an X.
Figure 4.2: Incompatible battery types (V18, 48-11-2200).

Compatible Milwaukee 18V Li-ion Battery Models:

  • 48-11-1815, 48-11-1828, 48-11-1840
  • 4932 3520 02, 4932 3520 71, 4932 3526 67, 4932 4300 63
  • 4932352002, 4932352071, 4932352667, 4932430063
  • C18 B, C18BX, M18, M18B, M18B2, M18B4, M18BX

4.2. Installing Scalding Heads

The device comes with three sizes of scalding heads: 20mm, 25mm, and 32mm. Choose the appropriate size for your pipe diameter.

  1. Ensure the device is turned off and cool.
  2. Attach the desired scalding heads to the heating plate using the provided nuts and wrench.
  3. Tighten securely to prevent movement during operation.

5. Operating Instructions

5.1. Power On and Temperature Setting

  1. Insert a charged, compatible 18V Li-ion battery into the device.
  2. Press and hold the 'Electric switch' button (usually for 3 seconds) to power on the device. The digital display will illuminate.
  3. The device features an intelligent temperature control chip. The working temperature is adjustable from 230°C to 320°C.
  4. Use the '+' and '-' buttons on the control panel to adjust the desired welding temperature. The 'Display screen' will show the current temperature.
  5. Wait for the device to reach the set temperature. The 'Temperature reaches' indicator will light up when ready.
Close-up of the control panel showing the digital display, power display, start heating indicator, temperature reached indicator, temperature rise (+) button, cooling (-) button, and electric switch.
Figure 5.1: Control panel overview.
Digital display showing the current temperature reading.
Figure 5.2: Digital temperature display.

5.2. Welding Process

This device is suitable for welding common pipes such as PPR, PPB, and PPE.

  1. Once the device reaches the desired temperature, carefully insert the pipe ends into the corresponding scalding heads.
  2. Hold the pipe ends in place for the recommended heating time (refer to pipe manufacturer specifications for exact times). The device provides uniform and stable heat conduction for rapid fusion.
  3. Remove the pipe ends from the scalding heads and immediately join them together, applying slight pressure.
  4. Hold the joint firmly until the plastic cools and sets, creating a tight and secure weld.
Image illustrating the rapid fusion process of pipes using the hot melt device.
Figure 5.3: Rapid fusion for pipe welding.
Examples of PPR, PPB, and PPE tubes that can be welded with the device.
Figure 5.4: Compatible pipe types (PPR, PPB, PPE).
Collage of images showing the hot melt device being used in various construction scenarios without a direct power supply, highlighting its portability.
Figure 5.5: Device in various construction scenarios.
Image showing the hot melt device connected to a water pipe, emphasizing its wireless portability and use in locations without power supply.
Figure 5.6: Wireless portability for welding water pipes.

Video 5.1: Product overview and demonstration of the hot melt device.

6. Maintenance

6.1. Cleaning

  • Ensure the device is turned off, unplugged (if applicable), and completely cool before cleaning.
  • Wipe the heating plate and scalding heads with a clean, dry cloth to remove any plastic residue.
  • Do not use abrasive cleaners or solvents that could damage the surface.
  • Cleaning and user maintenance should not be performed by children without supervision.

6.2. Storage

  • Store the device indoors in a dry place, away from direct sunlight and moisture.
  • Ensure all components, especially the scalding heads, are clean and dry before storage.
  • Remove the battery from the device if storing for extended periods.
Image showing the heat dissipation ports on the device, indicating proper ventilation for long working times.
Figure 6.1: Heat dissipation ports for maintaining device temperature.

7. Troubleshooting

  • Device not powering on: Ensure a charged, compatible 18V Li-ion battery is correctly installed. If the battery compartment does not slide in easily, it is not inserted correctly.
  • Device not heating: Verify the power switch is engaged and the temperature is set. If the device is damaged, do not attempt to repair it yourself.
  • Poor weld quality: Check that the correct scalding heads are used for the pipe size. Ensure sufficient heating time and proper pressure during joining.
  • Device malfunction after impact/water exposure: If the device has been dropped, damaged, left outside, or dropped into water, get it repaired by a professional. Do not use if there are broken, bent, cracked, or damaged parts.
  • Battery mismatch: If the product cannot function properly due to battery mismatch (e.g., using V18 or 48-11-2200 series batteries), the buyer is responsible for this incompatibility.

8. Specifications

Feature Specification
Model Number Subterrene-MWQ
Rated Voltage 21V
Rated Power 280W
Clamping Size (Scalding Heads) 20mm, 25mm, 32mm
Working Temperature 230°C ~ 320°C (Digital display, adjustable)
Dimensions (Approx.) 28cm (Length) x 13cm (Height)
Weight (Approx.) 0.8 kg
DIY Supplies Category Plumbing
Origin Mainland China
Diagram showing the dimensions of the hot melt device: 28cm in length and 13cm in height.
Figure 8.1: Approximate dimensions of the device.

9. User Tips

  • Battery Life: The lithium electric fuser is a high-temperature heating tool that requires significant power for continuous work. For extended operation, it is recommended to use high-capacity lithium batteries (e.g., greater than 5Ah) or have multiple batteries on hand.
  • Pre-heating: Allow the device to fully reach the set temperature before starting any welding to ensure consistent and strong joints.
  • Pipe Preparation: Always ensure pipe ends are clean, dry, and cut squarely before welding for optimal results.

10. Warranty and Support

For any questions, technical support, or warranty inquiries, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific warranty terms and contact information.

A user manual in PDF format is available for download. Please refer to the product page or contact customer support for the link: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.