HORACO HC-SWTGW215AS

Contents

HORACO 2.5GbE Managed Switch User Manual

Model: HC-SWTGW215AS

Brand: HORACO

1. Introduction

This manual provides comprehensive instructions for the installation, configuration, and maintenance of the HORACO 2.5GbE Managed Switch. It is intended for network installers and system administrators. A basic understanding of network communication protocols and technical networking terms is assumed.

The HORACO 2.5GbE Managed Switch is a high-performance network device designed to meet the demands of modern high-speed networks. It features 5x 2.5Gbps RJ45 ports and 1x 10Gbps SFP+ uplink slot, offering advanced web management capabilities including VLAN, QoS, Link Aggregation, and more.

2. Safety Information

Please read and follow all safety instructions carefully to prevent injury or damage to the device.

  • Ensure the power supply voltage matches the device's requirements (DC 12V1A).
  • Do not expose the device to water or excessive humidity.
  • Operate the device within the specified temperature and humidity ranges (Working Temperature: 0~40℃, Working Humidity: 10%~90% Non-condensing).
  • Avoid blocking ventilation openings to prevent overheating.
  • Do not attempt to open or repair the device yourself. Refer all servicing to qualified personnel.

3. Package Contents

Verify that all items are present in the package:

  • Switch: 1 Pcs
  • Adapter: 1 Pcs
  • Manual: 1 Pcs
  • Certificate: 1 Pcs
  • Anti slip foot pad: x4

4. Product Overview

4.1 Front Panel

Front view of the HORACO 2.5GbE Managed Switch showing ports and LEDs.

The front panel features the following components:

  • PWR LED: Indicates power status.
  • 5 x 2.5G RJ45 Ports (Ports 1-5): For connecting network devices. Each port has two LEDs:
    • Green LED: Indicates 2.5G Link/Act.
    • Yellow LED: Indicates 10/100/1000M Link/Act.
  • 1 x SFP+ (10G) Port (Port 6): For connecting 1G/2.5G/10G SFP optical fiber modules.

4.2 Rear Panel

Rear view of the HORACO 2.5GbE Managed Switch showing power input and reset button.

The rear panel includes:

  • DC 12V1A Power Input: Connect the provided power adapter here.
  • Reset Button: Used to reset the device to factory defaults.

4.3 Design Features

  • Fanless Design: Ensures quiet operation.
  • Durable Construction: Made of matte textured iron metal body.
  • Efficient Heat Dissipation: Features heat dissipation holes on both sides for optimal performance.
Image showing the fanless design of the switch with heat dissipation holes.

The fanless design ensures quiet operation, making it suitable for various environments. The robust metal casing and heat dissipation features contribute to stable and reliable performance.

5. Specifications

Image detailing product parameters and specifications of the switch.

The following table outlines the technical specifications of the HORACO 2.5GbE Managed Switch:

AttributeValue
Product Name6 Port 2.5G Web Managed Ethernet Switch
Model NumberHC-SWTGW215AS
Port Definition5*100/1000/2500M RJ45 Port, 1*10G SFP Optical Port
Supply VoltageAdapter input: AC 100-240 V, Switch input: DC 12V1A
Backplane Bandwidth45Gbps
Packet Forwarding Rate33.48Mpps
MAC Address Table4K
Jumbo Frame16356bytes
Forwarding ModeStore and forward
Network ProtocolIEEE802.3, IEEE802.3u, IEEE802.3z, IEEE802.3ab, IEEE802.3x, IEEE802.3bz
Network Medium10Base-T: Cat3, 4, 5 or above UTP/STP(≤100m)
100Base-TX: Cat5 or above UTP/STP(≤100m)
1000Base-TX: Cat5 or above UTP/STP(≤100m)
Working Temperature0~40℃
Storage Temperature-40~70℃
Working Humidity10%~90%, Non-condensing
Storage Humidity5%~95%, Non-condensing
Product Net Weight223g
Product Gross Weight364g
Product Size (L×W×H)113mm×90mm×25mm
CertificationCE, FCC, RoHS
Image showing the switch in an environment with temperature resistance indicators, 0 to 40 degrees Celsius.

The switch is designed for normal operation between 0℃ and 40℃, making it adaptable to various environments.

6. Setup and Installation

6.1 Physical Connection

  1. Connect Network Devices: Use standard Ethernet cables (Cat5e or above) to connect your network devices (e.g., computers, NAS, WiFi 6 APs, 2.5G routers) to the 2.5G RJ45 ports (Ports 1-5) on the switch.
  2. Connect SFP+ Modules (Optional): If using SFP+ modules for uplink or high-speed connections, insert the adaptive 1G/2.5G/10G optical fiber module into the SFP+ (10G) port (Port 6).
  3. Power On: Connect the provided DC 12V1A power adapter to the power input on the rear panel of the switch, then plug the adapter into a power outlet. The PWR LED on the front panel should illuminate.
Image showing the switch meeting high performance and 2.5G device requirements, with icons for NAS, WiFi 6 AP, AC Manager, 2.5G Router, Computer.

The switch supports MDI/MDIX automatic flipping, allowing for plug-and-play connectivity without needing specific cable types (straight-through or crossover).

Image showing the switch with cables connected, highlighting SFP+ module support.

The SFP+ port is adaptive, supporting 1G, 2.5G, and 10G optical fiber modules.

7. Web Management Login

7.1 Accessing the Web Interface

  1. Connect PC: Connect your PC directly to any of the switch's RJ45 ports.
  2. Configure PC IP Address: Ensure your PC's IP address is in the same network segment as the switch but is different from the switch's default IP. For example, set your PC's IP to 192.168.2.x (where x is any number from 2 to 254, but not 1) and the subnet mask to 255.255.255.0.
  3. Open Web Browser: Launch a web browser (Chrome 23.0+, Firefox 20.0+, or IE 9.0+ are recommended).
  4. Enter Switch IP: In the browser's address bar, type the default switch IP address: http://192.168.2.1 and press Enter.

7.2 Login Credentials

Screenshot of the Web Management Login interface.

A login window will appear. Enter the default credentials:

  • Username: admin
  • Password: admin

Click "Log in" to access the switch's web management system.

7.3 Navigation Bar Overview

The web interface features a navigation bar with main menu items: System, Configuration, Security, Monitoring, and Tools. Each main item contains submenus for detailed settings.

Menu ItemSubmenuDescription
SystemInformationDisplay port state and product info
IP SettingConfigure and view the management IP address
User AccountConfigure and view the management account
Port SettingConfigure and view all ports

8. Configuration

8.1 System Settings

8.1.1 Information

Displays system details such as Device Model, MAC Address, IP Address, Netmask, Gateway, Firmware Version, Firmware Date, and Hardware Version.

8.1.2 IP Setting

Allows changing the management IP address of the switch.

  • DHCP Setting: Enable or disable DHCP client.
  • IP Address, Netmask, Gateway: Manually configure network settings.

8.1.3 User Account

Allows users to check and modify the current username and password for web management access.

8.1.4 Port Setting

Enables querying and configuring individual Ethernet ports.

  • State: Enable or disable the port.
  • Speed/Duplex: Configure the port's speed and duplex mode (e.g., 10M/Half, 100M/Full, 2500M/Full).
  • Flow Control: Enable or disable PAUSE frame reception/transmission to manage network congestion.

8.2 VLAN (Virtual Local Area Network)

VLANs segment a physical LAN into logical broadcast domains, enhancing network efficiency and security.

Diagram illustrating One-Click VLAN Setup to prevent network storms by segmenting the network.

The diagram above illustrates how VLANs can be used to segment a network, preventing network storms and isolating traffic.

8.2.1 802.1Q VLAN

Configure VLANs based on the IEEE 802.1Q standard.

  • VLAN ID: A unique identifier for the VLAN (range 1-4094). VLAN 1 is the default and cannot be deleted.
  • VLAN Name: An optional descriptive name for the VLAN.
  • Port Selection: Assign ports as Tagged, Untagged, or Not Member for the selected VLAN.

8.2.2 802.1Q VID

Configure Port VLAN ID (PVID) and accepted frame types for each port.

  • PVID: The default VLAN ID for untagged frames entering the port.
  • Accepted Frame Type: Defines the types of frames the port will accept.

8.3 QoS (Quality of Service)

QoS allows prioritizing network traffic to ensure critical applications receive sufficient bandwidth and low latency.

8.3.1 Port to Queue

Sets processing priorities for different tags of data frames.

  • Queue: Assigns a queue priority (1-8) to a port.

8.3.2 Queue Weight

Configures the weight for each queue, influencing how bandwidth is allocated.

  • Weight: Can be set to "Strict priority" or a value from 1-15 for Weighted Round Robin (WRR) scheduling.

8.4 Loop Protocol

Loop detection and prevention mechanisms help maintain network stability by identifying and mitigating network loops.

Diagram illustrating Loop Protocol Settings and detection in a network.

The switch sends loop detection packets. If a loop is detected, the corresponding port LED will blink, and if loop avoidance is enabled, the port will be blocked to prevent network storms.

8.4.1 Loop Detection/Prevention

  • Loop Function: Enable or disable loop detection, loop prevention, or Spanning Tree.
  • Time Interval: Sets how often loop detection packets are sent (1-32767 seconds).
  • Recover Time: Sets the time before a blocked port can recover (0 or 4-255 seconds).

8.4.2 STP Global (Spanning Tree Protocol)

RSTP (Rapid Spanning Tree Protocol) eliminates physical loops in the data link layer, ensuring an optimal tree topology and fast convergence.

  • Force Version: Configure STP mode (e.g., RSTP).
  • Priority, Maximum Age, Hello Time, Forward Delay: Configure STP parameters.

8.4.3 STP Port

Configure STP settings for individual ports.

  • Path Cost: Cost associated with the port for STP calculations.
  • Priority: Port priority for STP.
  • P2P (Point-to-Point): Enable or disable P2P link type.
  • Edge: Configure as an edge port (typically for end devices).

8.5 IGMP Snooping (Internet Group Management Protocol)

IGMP Snooping optimizes multicast traffic by forwarding it only to ports where multicast receivers are present, preventing unnecessary flooding.

  • Enable: Enable or disable IGMP Snooping.
  • Dump IGMP entry: Display multicast group entries.

Link Aggregation (LAG) bundles multiple physical Ethernet links into a single logical link, increasing bandwidth and reliability.

Image showing the switch connected to a NAS, illustrating Link Aggregation support.

The switch supports Link Aggregation, allowing you to combine multiple ports for increased throughput and redundancy, as shown with the NAS connection.

8.6.1 Static Trunk Group

Manually configure Eth-Trunks and add member interfaces. All active links participate in data forwarding and share traffic evenly.

  • Group ID: Identifier for the trunk group (1-2).
  • Ports: Select up to 4 member ports for the LAG.

Dynamically aggregates and disaggregates links based on IEEE 802.3ad, exchanging information with opposite network devices via LACPDU.

  • Group ID: Identifier for the LACP group.
  • Type: Select LACP.
  • Member port, Aggregated Port: Select ports to be part of the LACP group.

8.7 Port-based Mirroring

Copies traffic from a specified source port to a destination port for monitoring and analysis.

  • Mirror Direction: Select Rx (receive), Tx (transmit), or Both.
  • Mirroring Port: The port where traffic is copied from (source port).
  • Mirrored Port List: The port where the copied traffic is sent to (destination port).

8.8 Port Isolation

Prevents communication between specified ports within the same VLAN, enhancing security.

  • Port: Select the port to configure.
  • Port Isolation List: Define the list of ports that will be isolated from the selected port.

8.9 Bandwidth Control

Restricts the data transmission and reception rates on physical interfaces.

  • Port: Select the port.
  • Type: Ingress (inbound) or Egress (outgoing) direction.
  • State: Enable or disable rate limiting.
  • Rate: Set the maximum rate in Kbit/sec.

8.10 Jumbo Frame

Configures the Maximum Transmission Unit (MTU) of the port to support larger Ethernet frames, improving efficiency for high-throughput applications.

  • Jumbo Frame (Bytes): Set the MTU size (default 16383 bytes).

8.11 MAC Constraint

Limits the number of MAC addresses that can be learned on a specific port, enhancing security.

  • Port: Select the port.
  • State: Enable or disable MAC constraint.
  • Entry Limits: Set the maximum number of MAC addresses allowed (e.g., Unlimited or a specific number).

8.12 EEE (Energy Efficient Ethernet)

Enables or disables Energy Efficient Ethernet functionality, allowing the switch to save power during periods of low network activity.

  • EEE Function: Enable or disable EEE.

9. Security

9.1 MAC Address

Manages MAC address entries for efficient and secure forwarding of network messages.

Displays the dynamically learned MAC address table, including MAC Address, VLAN ID, and Port.

  • Clear Dynamic Entries: Clears all dynamically learned MAC addresses.

9.1.2 Static MAC

Allows manual configuration of MAC address entries, which do not age out.

  • MAC Address, VLAN ID, Port: Manually add static MAC entries.

9.2 Storm Control

Prevents network storms caused by excessive broadcast, unknown multicast, or unknown unicast traffic by suppressing messages that exceed configured rate thresholds.

  • Storm Type: Select Broadcast, Known Multicast, Unknown Unicast, or Unknown Multicast.
  • Port: Select the port to apply storm control to.
  • State: Enable or disable storm control.
  • Rate: Set the maximum allowed rate in kbps.

10. Monitoring

10.1 Port Statistics

Displays real-time statistics for each port, useful for network diagnostics and performance monitoring.

  • Port: The port number.
  • State: Current state of the port (Enable/Disable).
  • Link Status: Current link status (Link Up/Link Down).
  • TxGoodPkt: Number of successfully transmitted packets.
  • TxBadPkt: Number of unsuccessfully transmitted packets.
  • RxGoodPkt: Number of successfully received packets.
  • RxBadPkt: Number of unsuccessfully received packets.
  • Clear: Clears the current port statistics.

11. Tools

11.1 Firmware Upgrade

Allows updating the switch's firmware to the latest version.

  1. Navigate to Tools > Firmware Upgrade.
  2. Select the firmware file from your local machine.
  3. Click "Upgrade".

Note: Do not power off the device during the upgrade process. Stay on the upgrade page for approximately 1 minute until the upgrade is complete.

11.2 Configuration Backup

Backs up the current switch configuration to a file.

  1. Navigate to Tools > Configuration Backup.
  2. Click "Backup" to save the configuration file.

11.3 Reset

Resets the switch to its factory default settings.

  1. Navigate to Tools > Reset.
  2. Click "Restore" to perform a factory reset and reboot the system.

11.4 Save

Saves the current running configuration to persistent memory, ensuring settings are retained after a reboot.

  1. Navigate to Tools > Save.
  2. Click "Save" to save the configuration.

11.5 Reboot

Restarts the switch system.

  1. Navigate to Tools > Reboot.
  2. Click "Reboot" to restart the switch.

11.6 Logout

Exits the web management interface.

  1. Navigate to Tools > Logout.
  2. Click "Login" (or similar button) to log out.

12. Troubleshooting

Common Issues and Solutions

  • No Power:
    Ensure the power adapter is securely connected to both the switch and a working power outlet. Verify the power outlet is functional.
  • No Link on Port:
    Check the Ethernet cable connection at both ends. Ensure the cable type is appropriate (Cat5e or above). Verify the connected device is powered on and functioning correctly. Check the port's Link/Act LEDs.
  • Cannot Access Web Management Interface:
    Verify your PC's IP address is in the same subnet as the switch (e.g., 192.168.2.x, subnet mask 255.255.255.0) and is not the same as the switch's IP (192.168.2.1). Ensure you are using the correct default IP address (http://192.168.2.1). Try a different web browser. If still unable to access, reset the switch to factory defaults (see Section 11.3) and try again.
  • Forgot Login Password:
    If you have forgotten the login password, you will need to perform a factory reset (see Section 11.3) to restore the default username "admin" and password "admin".

Frequently Asked Questions (FAQ)

  • Q: What is the fabric switching capacity of this switch?
    A: The fabric switching capacity is 45Gbps.
  • Q: Is this a Layer 2 or Layer 3 switch?
    A: This is a Layer 2 (Ethernet) managed switch.
  • Q: Where can I find the software for updates?
    A: Firmware updates are typically provided by the manufacturer. Please refer to the official HORACO website or contact their technical support for the latest firmware and instructions.

13. User Tips

  • For optimal performance, especially with 2.5GbE and 10GbE connections, always use high-quality Ethernet cables (Cat6a or Cat7 recommended for longer runs).
  • Regularly back up your switch configuration (see Section 11.2) before making significant changes or firmware upgrades.
  • If experiencing network issues, check the port statistics (Section 10.1) for errors or unusual traffic patterns.
  • Utilize VLANs (Section 8.2) to segment your network for improved security and performance, especially in environments with multiple device types or user groups.
  • Consider using Link Aggregation (Section 8.6) for connections to devices like NAS servers or other switches to increase bandwidth and provide redundancy.

14. Warranty and Support

14.1 Warranty Information

This HORACO product comes with a 1-year free warranty from the date of purchase. This warranty covers manufacturing defects and ensures the product meets its specified performance.

14.2 Technical Support

HORACO provides lifetime professional technical support for this product. If you encounter any issues or have questions regarding the setup, configuration, or operation of your switch, please contact HORACO customer support.

14.3 Additional Resources

A detailed user manual in PDF format is available for download. You can reference it for more in-depth information:

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.