Introduction
Thank you for choosing the XIWANGFIRE 100 LED Solar Wall Lamp. This manual provides essential information for the safe and efficient operation of your new solar light. Designed for outdoor use, this lamp features a 4-sided luminous design, motion sensing capabilities, and IP65 waterproofing, making it ideal for illuminating courtyards, stairs, gardens, patios, and driveways.
Specifications
| Feature | Detail |
|---|---|
| Item Type | Outdoor Solar Light |
| LED Quantity | 100 SMD2835 LEDs |
| Light Color | White Light |
| Body Material | PC+ABS |
| Solar Panel | Polysilicon 5.5V 1.43W |
| Battery | 18650 Lithium Battery (Included) |
| Charging Time | 8 hours in direct sunlight |
| PIR Sensing Angle | 120 degrees |
| PIR Sensing Distance | 3-8 meters |
| Waterproof Level | IP65 |
| Product Size | 13.5 x 9.7 x 5 cm |
| Item Weight | 168g |
| Illumination Angle | 270 degrees |
| Luminous Flux | 700 Lumens (up to 1400 max luminous) |
| Working Temperature | -40°C to 85°C |
| Certification | CCC, CE, FCC, PSE, ROHS |
The product parameters are also visually represented in the image below:
Setup and Installation
- Initial Charge: Before first use, place the solar lamp in direct sunlight for 2-3 days to ensure the battery is fully charged. This is crucial for optimal performance.
- Choose Location: Select an outdoor location that receives ample direct sunlight throughout the day. The lamp has a light control function, meaning it charges during the day and only operates automatically in dark environments. Avoid installing it in shaded areas or places with obstructions that could block sunlight or cause the lamp to activate during daylight hours.
- Mounting: The lamp is designed for wall mounting. Use appropriate screws and anchors (typically included) to securely fasten the lamp to a wall. Ensure the solar panel faces upwards towards the sun.
- Select Mode: In a dark environment or by covering the solar panel, press the power button to cycle through and select your desired lighting mode. It is recommended to set the mode before final installation.
Operating Instructions
The XIWANGFIRE 100 LED Solar Wall Lamp features three intelligent lighting modes, selectable via a button on the device. The lamp automatically charges during the day and operates only in dark conditions.
Selecting Lighting Modes:
To select a mode, cover the solar panel or wait until it's dark, then press the power button to cycle through the options:
- Mode 1: Motion Sensor Mode
The light remains OFF in darkness. When motion is detected within 3-8 meters, the lamp turns on to BRIGHT LIGHT for approximately 20-25 seconds, then turns OFF. - Mode 2: Dim Light + Motion Sensor Mode
The light stays at a DIM LIGHT (approx. 10% brightness) in darkness. When motion is detected, it switches to BRIGHT LIGHT for approximately 20-25 seconds, then returns to DIM LIGHT. - Mode 3: Light Control Mode (Continuous Dim Light)
The light automatically turns on to a continuous DIM LIGHT (approx. 30% brightness) in darkness and stays on until dawn or battery depletion. This mode does not use the motion sensor. - Mode 4: Light-off Mode
Pressing the button again after Mode 3 will turn the light completely OFF.
Maintenance
- Cleaning: Regularly wipe the solar panel with a soft, damp cloth to remove dust, dirt, or debris. A clean solar panel ensures maximum sunlight absorption and efficient charging.
- Optimal Placement: Periodically check that the lamp's location still receives adequate direct sunlight, especially after seasonal changes or new foliage growth.
- Battery Longevity: The integrated 18650 lithium battery is designed for long-term use. Avoid frequent deep discharges if possible, though the solar charging system manages this automatically.
- Weather Resistance: The IP65 rating ensures protection against dust and water jets. While designed to withstand various weather conditions (from -40°C to 85°C), extreme conditions may temporarily affect performance.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on at night. | Insufficient charging; Incorrect mode selected; Solar panel obstructed. | Ensure the lamp receives 8 hours of direct sunlight. Verify the selected mode (e.g., not in 'Light-off Mode'). Clean the solar panel and remove any obstructions. |
| Light is dim or flashes. | Battery is low; Insufficient charging; Dirty solar panel. | Allow the lamp to fully charge in direct sunlight for 2-3 days. Clean the solar panel. Ensure no external light sources are interfering with the light sensor. |
| Motion sensor not working or too sensitive. | Incorrect mode selected; Sensor obstructed; Interference from other light sources. | Ensure Mode 1 or Mode 2 is selected. Check for any physical obstructions blocking the sensor. Avoid placing the lamp near other strong light sources that might interfere with its operation. |
| Lamp turns on during the day. | Solar panel is covered or in a dark area; Faulty light sensor. | Relocate the lamp to an area with consistent direct sunlight. Ensure the solar panel is not covered. |
User Tips
- Optimal Installation Height: For best motion detection and illumination coverage, consider installing the lamp at a height of approximately 2-3 meters (6.5-10 feet) from the ground. This allows the 120-degree sensor to cover a wider area effectively.
- Solar-Powered Only: This device is designed to be entirely solar-powered. It cannot be connected to an electric line for power. Rely on sufficient sunlight for charging.
- Battery Information: The lamp uses an 18650 lithium battery. While the exact mAh capacity is not specified, ensuring full charge before first use and consistent daily sunlight exposure will maximize its performance and lifespan.
- Motion Sensor Control: If you prefer the light to stay on continuously at a dim level without motion activation, select Mode 3 (Light Control Mode). If you wish to turn the light off completely, cycle to Mode 4.
Frequently Asked Questions (FAQ)
- Q: What type of light source does this lamp use?
- A: The lamp uses 100 SMD2835 LED lights, providing bright white illumination.
- Q: Can I connect this solar light to my home's electrical system?
- A: No, this is a purely solar-powered device and cannot be connected to an electrical grid.
- Q: How many lumens does this light produce?
- A: The lamp provides 700 lumens of lighting, with a maximum luminous output of 1400.
- Q: Can the motion sensor be disabled?
- A: Yes, by selecting Mode 3 (Light Control Mode), the lamp will provide continuous dim light without motion sensor activation. You can also select Mode 4 to turn the light off completely.
Warranty and Support
For any issues or questions regarding your XIWANGFIRE 100 LED Solar Wall Lamp, please contact the seller or retailer from whom you purchased the product. Keep your purchase receipt as proof of purchase for any warranty claims.
