1. Introduction
The Makita DX05 Dust Collector Attachment is designed to provide efficient dust extraction when used with compatible Makita 18V LXT® Cordless Brushless Rotary Hammers, specifically the XRH12 model. This attachment features a HEPA filtration system to capture fine dust particles, ensuring a cleaner work environment and compliance with OSHA Table 1 regulations. It is powered by the rotary hammer's motor fan blade to maintain consistent suction performance during drilling operations.
2. Key Features
- Efficient HEPA Filtration: Captures 99.97% of particulates 0.3 microns and larger.
- OSHA Table 1 Compliant: Designed to meet dust extraction requirements for concrete drilling.
- Integrated Power: Powered by the rotary hammer's motor fan blade for consistent suction.
- Automatic Activation: Captures concrete dust during drilling and is activated by the tool for operator convenience, including a 3-second delay to capture remaining dust.
- Two-Stage Extractor Extension: Allows drilling up to 3-1/2 inches deep and up to 11/16 inch diameter holes.
- Depth Stop Adjustment: Features a button for accurate drilling depth control.
- Transparent Dust Container: Provides clear visibility for determining container fullness and features a quick-release mechanism for easy detachment.
- Filter Cleaning Mechanism: On-board mechanism designed to help maintain optimum suction efficiency.
3. Setup
- Compatibility Check: Ensure your rotary hammer is a compatible Makita 18V LXT® model, specifically the XRH12.
- Attachment: Align the DX05 dust collector with the mounting points on your rotary hammer. Slide the attachment onto the tool until it securely locks into place. Refer to your rotary hammer's manual for specific attachment instructions if needed.
- Depth Stop Adjustment: Press the depth stop adjustment button and extend or retract the extractor extension to set the desired drilling depth. Release the button to lock the depth.
- Dust Container Check: Ensure the transparent dust container is securely attached and empty before beginning work.
4. Operating Instructions
- Power On: Once the DX05 is securely attached and the depth stop is set, activate your rotary hammer. The dust extractor will automatically engage with the tool.
- Drilling: Begin drilling into the concrete surface. The DX05 will capture concrete dust as you drill.
- Post-Drilling Suction: After releasing the trigger of the rotary hammer, the dust extractor will continue to operate for approximately 3 seconds to ensure all remaining dust is captured.
- Monitor Dust Container: Periodically check the transparent dust container to monitor its fullness.
5. Maintenance
- Emptying the Dust Container: When the transparent dust container appears full, press the quick-release button to detach it from the main unit. Empty the collected dust into an appropriate waste receptacle.
- Filter Cleaning: The DX05 includes an on-board filter cleaning mechanism. Refer to the specific instructions provided with the product for operating this mechanism to maintain optimum suction efficiency. Regularly clean the HEPA filter to ensure peak performance.
- Reassembly: After emptying and cleaning, securely reattach the dust container to the DX05 unit.
- Storage: Store the DX05 in a clean, dry place away from direct sunlight and extreme temperatures.
6. Troubleshooting
- Reduced Suction: If you experience reduced suction, check the dust container for fullness and empty it if necessary. Ensure the HEPA filter is clean; use the filter cleaning mechanism or manually clean as per instructions. Verify that the attachment is securely connected to the rotary hammer.
- Dust Leakage: Ensure all components, especially the dust container, are properly seated and locked. Check for any cracks or damage to the housing or seals.
- Attachment Not Activating: Confirm that the DX05 is correctly attached to a compatible rotary hammer (XRH12) and that the rotary hammer itself is functioning correctly.
7. Specifications
| Feature | Specification |
|---|---|
| Model Number | DX05 |
| Compatibility | Makita 18V LXT® Cordless Brushless 11/16" Rotary Hammer (XRH12) |
| Filtration Type | HEPA Filter |
| Filtration Efficiency | 99.97% of particulates 0.3 microns and larger |
| Max. Drilling Depth | 3-1/2 inches (88.9 mm) |
| Max. Drilling Diameter | 11/16 inches (17.46 mm) |
| Compliance | OSHA Table 1 |
| Origin | Mainland China |
| Certification | CE, FCC |
| DIY Supplies Category | Electrical |
8. User Tips
- Regular Dust Container Checks: To maintain optimal suction and prevent overflow, frequently check the transparent dust container and empty it before it becomes completely full.
- Filter Maintenance: Utilize the built-in filter cleaning mechanism regularly, especially after heavy use, to ensure the HEPA filter remains effective and prolongs its lifespan.
- Secure Attachment: Always ensure the DX05 is firmly attached to your rotary hammer before starting any drilling task to prevent dislodgement and ensure proper dust collection.
9. Warranty and Support
For warranty information, service, or technical support, please refer to the documentation included with your original purchase or contact Makita customer service directly. Ensure you have your product model number (DX05) and proof of purchase available when seeking support.
