1. Introduction
The FD 868MHz Wireless Handheld Transmitter is a versatile remote control designed for operating garage doors, barriers, and gates. It utilizes a rolling code encoding method for enhanced security and is compatible with a range of specific models. This manual will guide you through the setup, programming, and maintenance of your new remote control.
2. Specifications
| Feature | Detail |
|---|---|
| Brand Name | FD |
| Frequency | 868MHz |
| Encoding Method | Rolling code |
| Certification | CE |
| Origin | Mainland China |
| High-concerned chemical | None |
Package Dimensions and Weight:
- Length: 13 cm
- Width: 8 cm
- Height: 2 cm
- Weight: 0.052 kg
3. Compatible Models
This remote control is compatible with the following models. Please ensure your original remote control's model number is listed below for proper functionality. The model number can typically be found on the back of your original remote control.
- HSP 4 BS
- HSD 2 BS
- HSS 4 BS
- HSP4-868-BS
- HSD2-868-BS
- HSS4-868-BS
- HS 1 BS / HS 4 BS / HS 5 BS
- HSE 1 BS / HSE 2 BS / HSE 4 BS
- HSE1-868-BS / HSE2-868-BS / HSE4-868-BS
4. How to Program (Learning Process)
Follow these steps to program your new remote control to copy the code from your original remote:
- Prepare the New Remote: Press and hold the button on the new remote where you want to store the code. While holding it, press any other button 3 times until the LED red light is on for 10 seconds. Release all buttons.
- Position Remotes: Place your original remote control on the left side of the new remote control, ensuring they are as close as possible.
- Copy the Code: Press the button on the original remote control that you wish to copy. Continue pressing until the LED on the new remote flashes red and blue alternately. Verify that the LED of the new remote is flashing blue. If not, adjust the proximity of the remotes and try again.
- Complete Learning: When the blue light of the new remote control flashes quickly, the learning process for that button is complete. Release all buttons.
- Repeat for Other Buttons: Perform the same procedure for any remaining buttons you wish to program.
5. Reset Method
To assign new radio codes to each button of your remote control, follow these steps:
- Remove Battery: Remove the battery from the remote control for 10 seconds.
- Press and Hold Button: Press and hold one button of the remote control.
- Insert Battery: While still holding the button, insert the battery. The LED will slowly flash blue for 4 seconds, then quickly flash blue for 2 seconds, and finally illuminate blue for a long time.
- Release Button: Release the button. All radio codes are now newly assigned.
Note: If the button of the remote is released prematurely, no new radio codes will be assigned.
6. User Tips
- Decorative Button: For some models, such as the black flip-style remote, one button (often labeled '1') is for decoration only and does not have any functional purpose. Refer to Figure 5 for clarification.
- Verify Compatibility: Always double-check that your existing garage door or gate opener system is compatible with the listed models before attempting to program the new remote.
- Optimal Proximity: During the programming process, ensure the new and original remotes are placed as close as possible to each other to facilitate successful code learning.
7. Troubleshooting
- Remote Not Responding: If the remote control does not respond after programming, ensure that the original remote was placed as close as possible during the learning process. Check the battery level of both remotes.
- Programming Failure: If programming fails, try the reset method (Section 5) and then attempt the programming steps again. Ensure the LED indicators behave as described in the programming instructions.
- Intermittent Operation: Weak battery or interference can cause intermittent operation. Replace the battery with a fresh one and ensure there are no strong radio frequency sources nearby.
8. Maintenance
- Cleaning: Keep the remote control clean and dry. Use a soft, dry cloth to wipe the surface. Avoid using harsh chemicals or abrasive cleaners.
- Storage: Store the remote control in a cool, dry place away from direct sunlight and extreme temperatures.
- Battery Replacement: Replace the battery when the LED indicator becomes dim or the remote becomes unresponsive. Refer to the reset method (Section 5) if a full reset is needed after battery replacement.
9. Warranty and Support
This product typically comes with a 1-year warranty from the date of purchase. For any technical support, troubleshooting assistance, or warranty claims, please contact the seller directly through your purchase platform. Ensure you have your order details ready when contacting support.
