1. Introduction
This manual provides detailed instructions for the proper use, setup, and maintenance of ABBIDOT dog training system accessories. These accessories are designed to complement your existing ABBIDOT T30, T50, or T60 series dog training collars, including remote controls, receivers, and various components like contact points and straps. Please read this manual thoroughly before using any accessory to ensure safe and effective operation.
2. Product Components
Depending on your purchase, your package may include one or more of the following accessories:
- Remote Control: Used to send commands to the receiver collar. Available for T30 and T50 series.
- Receiver Collar: The device worn by your dog that receives commands from the remote. Available for T30, T50, and T60 series.
- Metal Contact Points: Conductive probes that deliver static stimulation. Various lengths are available.
- Silicone Caps: Covers for contact points for added comfort or reduced stimulation.
- Wrench: Tool for installing and removing contact points.
- Collar Strap: Replacement or alternative strap for the receiver.
3. Setup and Installation
3.1 Attaching Contact Points to Receiver
- Select the appropriate length of metal contact points based on your dog's fur length. Longer points are for dogs with thick fur.
- Screw the chosen contact points into the threaded holes on the underside of the receiver. Use the provided wrench to tighten them securely, but do not overtighten.
- (Optional) Place silicone caps over the metal contact points for a softer touch or reduced stimulation intensity.
3.2 Attaching the Collar Strap
- Thread the collar strap through the slots on the receiver unit.
- Adjust the strap to fit snugly around your dog's neck, ensuring the contact points touch the skin. You should be able to fit two fingers comfortably between the strap and your dog's neck.
3.3 Pairing Remote and Receiver (If applicable)
If you have purchased a new remote or receiver, or if your devices are not responding, you may need to pair them. The exact pairing process may vary slightly between T30, T50, and T60 models. Refer to your original full system manual for precise instructions. A general pairing procedure is as follows:
- Ensure both the remote and receiver are fully charged.
- Turn on the receiver. Often, a light will flash.
- Press and hold the power button or a dedicated pairing button on the receiver until the indicator light flashes rapidly or changes color.
- Within a few seconds, press a stimulation button (e.g., static, vibration, or tone) on the remote control.
- The receiver's indicator light should become solid or flash slowly, indicating successful pairing.
4. Operating the Remote Control
The remote control allows you to deliver various commands to the receiver collar. While specific button layouts may differ between T30 and T50 remotes, common functions include:
- Power Button: Turns the remote on/off.
- Mode Selection: Buttons or a dial to switch between static stimulation, vibration, and tone modes.
- Intensity Level Adjustment: A dial (e.g., "PUSH +") or buttons to increase/decrease the intensity level of static or vibration.
- Channel Selection: If your system supports multiple collars, buttons to select which receiver to control.
Always start with the lowest stimulation level and gradually increase it to find the appropriate level for your dog's temperament and training needs.
5. Maintenance
- Cleaning: Regularly clean the receiver and contact points with a damp cloth. Ensure no dirt or debris accumulates around the contact points, as this can affect performance.
- Battery Care:
- Charge the remote and receiver fully before first use and whenever the battery indicator shows low power.
- Avoid overcharging.
- If storing for an extended period, charge the devices to about 50% and store in a cool, dry place. Recharge every few months to prevent deep discharge.
- Contact Point Inspection: Periodically check the contact points for wear or damage. Replace them if they appear bent or corroded to ensure proper function and your dog's comfort.
- Strap Inspection: Check the collar strap for signs of wear, fraying, or damage. Replace if necessary to ensure the receiver remains securely on your dog.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Receiver not responding to remote. | Not paired, low battery, out of range. | Re-pair devices (Section 3.3). Charge both units. Ensure within operational range. |
| No static stimulation or weak effect. | Poor contact with dog's skin, contact points too short, dirty contact points, low battery. | Adjust collar fit. Use longer contact points for thick fur. Clean contact points. Charge receiver. |
| Remote display is blank or unresponsive. | Low battery, remote is off. | Charge remote. Turn remote on. |
| Contact points bend or break easily. | Excessive force during installation or impact during use. | Ensure proper installation without overtightening. Consider using silicone caps for protection during active play. Replace damaged contact points. |
7. Specifications
| Feature | Detail |
|---|---|
| Brand | ABBIDOT |
| Model Compatibility | T30, T50, T60 Series |
| Item Type | Training Collars (Accessories) |
| Target Pet | Dog |
| Material | Plastic (for main units), Metal (for contact points) |
| Battery Included | Yes (for remotes/receivers) |
| Electrical | Yes |
| Smart Device | No |
| Package Weight | 0.2 kg |
| Package Dimensions (approx.) | 12 cm (L) x 5 cm (W) x 4 cm (H) |
8. User Tips
- Contact Point Selection: For dogs with thick fur, ensure you use longer contact points to guarantee proper skin contact. This is crucial for effective stimulation.
- Collar Fit: A snug fit is essential. The contact points must make consistent contact with your dog's skin. Regularly check the fit, especially after grooming or if your dog's weight changes.
- Check Contact Points: Periodically inspect contact points for any bending or damage. Damaged points can be ineffective or cause discomfort. Replace them if they show signs of wear.
- Pairing Confirmation: After pairing a new remote or receiver, always test the functions (tone, vibration, static) at a low level to confirm successful synchronization before using it on your dog.
9. Warranty and Support
For warranty information, technical support, or replacement parts, please contact ABBIDOT customer service directly. Refer to the packaging or the official ABBIDOT website for contact details. Keep your purchase receipt as proof of purchase for warranty claims.