1. Introduction
This manual provides essential information for the safe and efficient operation of your KKMOON Solar Charge Controller. This device is designed to manage the power flow from your solar panel to your battery and load, ensuring optimal charging and discharge protection. It features an adjustable LCD display and USB charging ports for convenience.
For detailed product usage precautions and specific instructions, please refer to the manual included in the product package or the content on the product details page. If you have any questions, please contact customer service.
2. Safety & Warnings
Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
- Handle with care to avoid cuts or injuries.
3. Product Overview
The KKMOON Solar Charge Controller is a Pulse Width Modulation (PWM) type controller designed for 12V/24V solar power systems. It automatically detects the system voltage and provides comprehensive protection features.
Key Features:
- Large LCD display for clear status indication and data.
- Convenient mode switching and parameter configuration.
- Automatic 12V/24V system voltage identification.
- Multiple protection functions: short-circuit, open-circuit, reverse polarity, and over-load protection.
- Dual USB outputs (5V/3A) for charging mobile devices.
- Suitable for various applications including solar power systems, street lamps, smart homes, and camping.
- Built-in timer for load control.
Compatibility Note:
This solar regulator is only suitable for lead-acid batteries (OPEN, AGM, GEL). It is NOT compatible with nickel hydride, lithium, Li-ion, or other battery types.
The controller must use a photovoltaic panel as the charging source. Do not use DC power supplies or other power sources for charging.
4. Setup and Installation
Before connecting, ensure all components are in good condition and the system voltage (12V or 24V) matches your battery and solar panel configuration.
Wiring Diagram:
Connection Order:
- Connect the battery to the charge controller first. Ensure correct polarity (+ to + and - to -). The controller will automatically detect 12V or 24V.
- Connect the solar panel to the charge controller. Ensure correct polarity.
- Connect the DC load to the charge controller. Ensure correct polarity.
Important: Always connect the battery first and disconnect the battery last to prevent damage to the controller.
Disconnection Order:
- Disconnect the DC load.
- Disconnect the solar panel.
- Disconnect the battery.
5. Operating Instructions
LCD Display and Buttons:
The controller features a visual dual LED display for various settings and real-time data. The buttons allow for navigation and parameter adjustment.
Button Functions:
- Menu Key: Press to enter or exit the setting menu.
- Page Up (▲): Navigate up through menu options or increase values.
- Page Down / Manual Operation (▼/☀): Navigate down through menu options, decrease values, or manually turn the load on/off when in load control mode.
Parameter Configuration:
To adjust settings such as equalization voltage, float charge voltage, discharge stop voltage, and discharge reconnect voltage:
- Press the Menu key to enter the setting mode.
- Use the Page Up (▲) and Page Down (▼) buttons to navigate through the parameters.
- Press the Menu key again to select a parameter for editing. The value will start blinking.
- Use the Page Up (▲) and Page Down (▼) buttons to adjust the value.
- Press the Menu key to confirm the new value and move to the next parameter, or long-press to save and exit.
Default Adjustable Parameters:
- Equalization: B01 sealed 14.4V, B02 Gel 14.2V, B03 flood 14.6V
- Float charge: 13.7V (adjustable)
- Discharge stop: 10.7V (adjustable)
- Discharge reconnect: 12.6V (adjustable)
Operation Demonstration Video:
6. Maintenance
- Keep the controller in a dry, well-ventilated area, away from direct sunlight and moisture.
- Regularly check all wire connections to ensure they are tight and secure.
- Inspect the controller and wiring for any signs of damage or corrosion.
- Clean the terminals periodically to prevent poor connections.
- Ensure proper ventilation around the controller to prevent overheating.
7. Troubleshooting
Common Issues:
- No display or unresponsive: Check battery connections and ensure the battery has sufficient charge.
- Battery not charging: Verify solar panel connections and ensure adequate sunlight. Check for any shading on the solar panel.
- Load not working: Check load connections and ensure the battery voltage is above the discharge stop voltage. Verify load control settings.
- Incorrect voltage readings: Ensure proper calibration if applicable (though this model is generally auto-calibrating). Check for loose connections.
If problems persist, refer to the full user manual (PDF) or contact customer support.
8. Specifications
| Parameter | Value |
|---|---|
| Battery Voltage | 12V/24V Auto |
| Charge Current | 10A - 100A (model dependent) |
| Discharge Current | 10A - 100A (model dependent) |
| Equalization (Sealed) | 14.4V |
| Equalization (Gel) | 14.2V |
| Equalization (Flood) | 14.6V |
| Float Charge | 13.7V (default, adjustable) |
| Discharge Stop | 10.7V (default, adjustable) |
| Discharge Reconnect | 12.6V (default, adjustable) |
| USB Output | 5V/3A |
| Self-Consume | <10mA |
| Operating Temperature | -35°C to +60°C |
| Weight | 150g |
| Dimensions (L*W*H) | 13.3 x 7 x 3.5 cm |
9. User Tips
- PWM Technology: This controller utilizes Pulse Width Modulation (PWM) technology for battery charging. While effective, it is different from Maximum Power Point Tracking (MPPT) controllers. Ensure this matches your system requirements.
- Battery Type Selection: Always ensure the correct battery type (Sealed, Gel, or Flood) is selected in the controller settings to prevent overcharging or undercharging.
- Initial Setup: Pay close attention to the connection order (Battery first, then Solar, then Load) during initial setup to avoid damaging the controller.
- Monitoring: Regularly check the LCD display for battery voltage and charging status to ensure optimal system performance.
10. Warranty & Support
For warranty information, technical support, or any product-related inquiries, please contact the store customer service staff where you purchased this product. They will be able to assist you with specific details regarding your purchase.
A detailed user manual in PDF format is also available for download: View User Manual (PDF)